11025 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
My washer lid lock light kept blinking and the washer would not start
17 of 18 people
found this instruction helpful.
-
Janice from GREENVILLE, NC
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
I followed the online video, removed the old part and replaced it with the new part. My washer is working perfectly. It took about an hour to reset.
Was this helpful?
Thank you for voting!
Making loud noises.
21 of 30 people
found this instruction helpful.
-
Roy from BROOKLYN, NY
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
The video you sent me was very helpful told me the exact tools I needed and how to do it.
Thank you
Thank you
Was this helpful?
Thank you for voting!
Would not spin
24 of 40 people
found this instruction helpful.
-
floyd from Slidell, LA
- Easy
- 1- 2 hours
-
Pliers, Screw drivers, Socket set
Remove the nut from the top of the motor shift inside of wsher. then remove the wire harness plug. Take out three bolts side the shaft and motor out. Replace clutch and install in reverse order.
Was this helpful?
Thank you for voting!
Washing Machine not draining
17 of 19 people
found this instruction helpful.
-
Kay from Houston, TX
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
1. Watch the partselect.com repair videos for either of the following parts: Part # 3363394 (White Direct Drive Water Pump - two ports) or Part # 285753A (Direct Drive Coupling).
2. After disconnecting the washing machine from the wall, these videos will show you how to disconnect the frame off the washing drum from the front. Disco ... Read more nnecting the top panel is a little different: pull/pop the two end pieces off, and unscrew the screws.
3. Upon removal of the front frame (per videos), disconnect the electrical device from underneath the lid, using a phillips screwdriver and a nutdriver and/or wrench. Use a flathead screw driver for the clips to remove/replace the electrical wires. No need to splice/cut any wiring.
4. Put everything back together.
2. After disconnecting the washing machine from the wall, these videos will show you how to disconnect the frame off the washing drum from the front. Disco ... Read more nnecting the top panel is a little different: pull/pop the two end pieces off, and unscrew the screws.
3. Upon removal of the front frame (per videos), disconnect the electrical device from underneath the lid, using a phillips screwdriver and a nutdriver and/or wrench. Use a flathead screw driver for the clips to remove/replace the electrical wires. No need to splice/cut any wiring.
4. Put everything back together.
Read less
Was this helpful?
Thank you for voting!
The washer did not spin fast enough during the rinse cycle to adequately dry the load of clothes
17 of 19 people
found this instruction helpful.
-
Richard from EL SEGUNDO, CA
- A Bit Difficult
- More than 2 hours
-
Socket set
I repaired my Kenmore washing machine replacing the clutch, Motor coupling and cogs. All of the parts came quickly and with good instructions. Best of all there were links to youtube repair walkthroughs. With out these step by step instructions this project would have taken much longer. Now the washer is like new! WATCH THE YOUTUBE PAUSE
... Read more
DO THE STEP AND REPEAT
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
The movers broke both water intakes off flush with the back of the machine
16 of 17 people
found this instruction helpful.
-
Dennis from Oak Island, NC
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
took off two screws that held the top part on took the screws that held the back on 4 screws removed the one screw that held the replacement valve put the black mounting plate on the machine replaced screws very simple.
Was this helpful?
Thank you for voting!
Top section of agitator not turning
17 of 20 people
found this instruction helpful.
-
John from Stone Mountain, GA
- Really Easy
- 15 - 30 mins
-
Socket set
Found directional gogs broken. Searched washer model # on PS.com and easily found schematic drawing. Received parts in a couple of days. Removed agitator with one nut, and other parts just pulled apart. Replaced the cogs and other parts which were not really broken....just worn. Everything went back together easily, and I was done!
... Read more
Parts Select saved me a LOT of time, and especially money, than if I had called a repair co. THANKS!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
The Agitator in my washing machine wasn't spinning, and was loose.
15 of 15 people
found this instruction helpful.
-
Anton from BRONX, NY
- Really Easy
- 30 - 60 mins
-
Socket set
After researching and learning from the university of YouTube, I ordered new agitator 'dogs' from PartSelect - the rubbery dogs which look like gummy bears, were worn out in my machine and needed to be replaced. These dogs secure the inner part of the agitator. After watching several videos on YouTube, I knew precisely what to do and what
... Read more
I needed. I researched and found PartSelect on-line and they were very helpful and sending me the dogs. It was a very simple fix, and my washing machine now is working like brand new. Thanks PartSelect for all your help and will reach out again for any future self-fix projects!!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Somehow or another, the plastic cup inside vanished.
17 of 21 people
found this instruction helpful.
-
Warren from Lakewood, CO
- Really Easy
- Less than 15 mins
This was a really easy replacement job. All I had to do was twist the old Fabric Softener Dispenser to the left to unlock it, pull it off, and put the replacement on.
Was this helpful?
Thank you for voting!
Water was leaking at the pump
17 of 21 people
found this instruction helpful.
-
Paul from Painesville, OH
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Actually this is kinda funny. I ordered the part and it arrived when I was out of town on business. My 20 year old daughter tipped the washer up on its end, and replaced the pump herself in less than 30 minutes. Her only complaint was that no one told her to block the washer up as it almost fell on her.
Was this helpful?
Thank you for voting!
Cold water flow was slow
22 of 36 people
found this instruction helpful.
-
Garry from Palm Bay, FL
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
Removed old part; exchanged rubber plungers between the hot and cold. Symptoms still the same - so eliminated the need for new rubber plungers (even though they still needed to be replaced). The only item left were the magnetic switches opening and closing the flows. The syphon was replaced due to broken plastic mountings causing the syph
... Read more
on to hang into the drum. Repair was a snap and finding the parts on your site was very easy and parts were there within 2 days at standard shipping. Thank you.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Noise, all the lubricant had leaked from the gearcase.
15 of 15 people
found this instruction helpful.
-
larry from SOD, WV
- Very Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
DO NOT do this repair from the top. The only thing needed to be removed from the top of the machine is the agitator and retaining clip. After removing these items, lay the machine on its front, on a table if you have a friend who will help. Remove the back cover. Simply disconnect the wiring, remove the water pump, the tub locking mec
... Read more
hanism, the belt, and motor. Remove the four bolts holding the gearcase. It should come out with little effort. Remove the old tub seal. There should be a new one on the replacement. Lubricate the new seal. Dishwashing liquid worked great. Move the drive wheel from the old gearcase to the replacement part. All the parts originally removed will only fit one way. Reverse all the removal steps and you be should be ready to go. My only problem with the replacement was there was no groove in the new part spline for the tub retaining clip. Seemed to be no problem since the agitator is bolted on so the tub is going nowhere.
Read less
Was this helpful?
Thank you for voting!
Washing machine leaking water
16 of 19 people
found this instruction helpful.
-
John from Oklahoma City, OK
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
First, I'm glad I found PartSelect. The previous posts for this repair told me exactly how to replace the pump: I unplugged the washer and moved it out away from the wall (did not need to disconnect water hoses). Then I tilted the washer back and propped it up so I could get underneath. Using pliers, slid hose clamps back and disconne
... Read more
cted hoses from pump. Using a screwdriver, popped off two clips, top and bottom, that hold the pump in place. Pump then slides right off the shaft. Installation is the reverse. Make sure you align the shaft with the pump. Delivery of my part was FAST - ordered it and got it the next day!
Read less
Was this helpful?
Thank you for voting!
Leaking drain hose
16 of 19 people
found this instruction helpful.
-
Steve from Cypress, CA
- Really Easy
- Less than 15 mins
-
Pliers
First I removed hose from drain, next I loosened the clamp at the drain hose connection at the washer. Removed hose. Have rags/towels as there is some residual water that will spill out of the washer. Reinstall in reverse.
Was this helpful?
Thank you for voting!
hoses had holes in them
18 of 25 people
found this instruction helpful.
-
Sharon from Dallas, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
Put clamps on hose end and then used some dishsoap on the inside of the hose to make pushing them into place easier once in place I placed the clamp in correct spot and used a screwdriver to tighten the clamps.
Other Parts Used:
Was this helpful?
Thank you for voting!