11025 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Waher would not spin and made noise
25 of 29 people
found this instruction helpful.
-
Andrew from SYLVANIA, OH
- Very Easy
- Less than 15 mins
-
Screw drivers, Wrench (Adjustable)
Removed center cap, loosened center nut, pry lightly up on center plate and tap center nut. Center plate comes loose, remove nut, remove center plate. Pry lock clip out and remove, remove screw with electric impact (screw drive will work, but slower), remove drive hub. Install new drive hub (be sure to check screw hole alignment), install
... Read more
and tighten screws (be sure to follow a skip pattern and bring it down even), install lock clip, install center plate, install and tighten nut, replace center cap. Done!
Read less
Was this helpful?
Thank you for voting!
The spin gear was striped.
25 of 31 people
found this instruction helpful.
-
Aaron from Lake Mills, WI
- A Bit Difficult
- 1- 2 hours
-
Pliers, Socket set
I had to take the motor and transmission out. They are one piece. Removed the clutch, take off trans. cover, remove a snap ring, take the striped gear off, and put the new one on. Then put put everything back on the way it came off.
Was this helpful?
Thank you for voting!
Washer lid switch worked sometime, sometime not
23 of 25 people
found this instruction helpful.
-
Jill from Alexandria, LA
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
First, I'm so excited that this site exists because I knew that the problem was minor and I didn't want to pay the outrageous housecall price of a repairman. I read other customers' experiences on how they fixed the problem and that made it sooo easy! Basically unscrewed the screws on the far left and right on the top panel, folded it dow
... Read more
n toward front, unscrewed and unplugged the ground wire and replaced the part. Someone else had warned that the lid should be open to remove it and that was a huge time-saver. Thanks so much! The part was broken because of very poor design. The part actually worked fine, but the piece of thin plastic that held the part in place broke. Back to the drawing board Whirlpool.
Read less
Was this helpful?
Thank you for voting!
washer wouldnt agitate or spinn but would drain?
22 of 22 people
found this instruction helpful.
-
lester from Belleville, WI
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
So i replaced the above parts pulled gearbox put new oil in all looked good but when i tryed it filled started spinning for a few sec.then quit again?was makeing a clicking sound so i layed on the floor and the drive coupling was spinning so i took the water pump off and it started agitating and spinning. found about a 6 in.thin piece of
... Read more
wire in it, dont know where it came from but installed a new pump and it works like a new one !!!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Agitator was locked up
24 of 28 people
found this instruction helpful.
-
Roger from Palmyra, IN
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
I had a little difficulty at first, trying to remove the back of the unit. I then figured out that the repair was to be made by leaning the washer back and removing it from underneath. That became really easy as the bottom is open.I had to remove one nut and then the agitator from inside, then tilt the machine back, disconnect the two ho
... Read more
ses from the pump, remove three bolts and lower the motor/ transmission assembly. Then I had to disconnect the motor from the pump ( with two snap on clips) and remove the broken plastic coupling. The new coupling had a metal insert that seems to make it stronger than the original piece.I then just reversed the procedure to put it together again and it worked fine. The part was shipped immediately and I got it sooner than I expected so I greatly appreciate that. Overall it went well, and by the way, it was my daughters washer and she was happy as well.Thanks, Roger
Read less
Was this helpful?
Thank you for voting!
My washer stopped mid-cycle and acted completely dead
22 of 23 people
found this instruction helpful.
-
Jeff from Ventura, CA
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
I thought the click of the lid switch sounded different so I pulled the top console and tested it for continuity in both positions and found none. When I by-passed the switch the washer started up, so I knew what the problem was. There are four screws involved to remove the console which reveals the lid switch to the left side. There's
... Read more
a single screw for a ground wire but the switch itself is simply snapped in place after disconnecting the wire harness plug (must be done with the lid open btw).
I was lucky to diagnose the problem accurately so that the first thing I suspected turned out to be the problem!
I was lucky to diagnose the problem accurately so that the first thing I suspected turned out to be the problem!
Read less
Was this helpful?
Thank you for voting!
washer not agitating
22 of 23 people
found this instruction helpful.
-
David from EAST AMHERST, NY
- Easy
- 15 - 30 mins
-
Socket set
This was a learning experience but it appears to have worked out in the end. Our 3 1/2 year old washer was not agitating much and I attributed that to a loose bolt. I would tighten the bolt and it would work ok for a load or two and then stop agitating. I would find that the bolt was loose again. I took a number of steps to try to get
... Read more
the bolt to stay on tight - threadlock, a new bolt, more threadlock, and applying progressively more force on the bolt, with no better results. Yet the repair guys on you tube were saying the bolt only needs to be snug, not super tight - something was amiss. I even went so far as to secure the basket with a rope so I could use two hands on the socket wrench (please don't do this). But when I tried the washer again there was no agitation at all! I observed the agitation output in manual test mode and the bolt was turning in lock step with the shaft but the agitator wasn't turning at all. That's when I suspected that the problem was actually a worn lower agitator. Trouble was that now I couldn't seem to get the bolt off. Turning the wrench caused the shaft itself to rotate so I couldn't loosen the bolt from the shaft. I thought I broke the washer. Then I considered that maybe the shaft was rotating because the washer was in an agitation mode when I turned it off. I went back into manual test mode, made the washer spin, then turned it off. Fortunately, this worked. The shaft was again stationary and, albeit with great difficulty, I got the bolt off.
I removed the agitator, and as a pro would have figured out long before, the ridges inside the top of the lower agitator were almost completely worn down. I realized then that the contact between these ridges and the splines on the shaft is what is supposed to cause the lower agitator to move with the shaft. The purpose of the bolt is just to keep the agitator in the correct position and from coming off the shaft. I had been trying to compensate for the worn agitator ridges by over-tightening the bolt, creating some contact at the top of the shaft. This would work for a little while, then the agitator would start slipping, and the slipping agitator was acting just like a wrench loosening the bolt (until my stupid rope trick, that is.)
So I ordered a new agitator (only the lower agitator was bad, but the price of an entire agitator isn't a lot more than just the lower part and I was reading that the upper agitator parts will wear over time) and another new bolt (because my repeated attempts to over-tighten the first one I ordered had split the rubber gasket apart and worn the bolt head).
The new agitator fit snugly on the splines of the shaft so I sensed no need to use excessive force on the bolt. Just an easy one-handed snug tightening with the socket wrench, using the other hand to hold the lower agitator. The washer is now working again.
I removed the agitator, and as a pro would have figured out long before, the ridges inside the top of the lower agitator were almost completely worn down. I realized then that the contact between these ridges and the splines on the shaft is what is supposed to cause the lower agitator to move with the shaft. The purpose of the bolt is just to keep the agitator in the correct position and from coming off the shaft. I had been trying to compensate for the worn agitator ridges by over-tightening the bolt, creating some contact at the top of the shaft. This would work for a little while, then the agitator would start slipping, and the slipping agitator was acting just like a wrench loosening the bolt (until my stupid rope trick, that is.)
So I ordered a new agitator (only the lower agitator was bad, but the price of an entire agitator isn't a lot more than just the lower part and I was reading that the upper agitator parts will wear over time) and another new bolt (because my repeated attempts to over-tighten the first one I ordered had split the rubber gasket apart and worn the bolt head).
The new agitator fit snugly on the splines of the shaft so I sensed no need to use excessive force on the bolt. Just an easy one-handed snug tightening with the socket wrench, using the other hand to hold the lower agitator. The washer is now working again.
Read less
Was this helpful?
Thank you for voting!
Water control would only fill to Medium load then stopped altogether
25 of 33 people
found this instruction helpful.
-
Wayne from University City, MO
- Really Easy
- Less than 15 mins
-
Screw drivers
I removed the screws holding the control board in place. Removed the knob on the front of the panel and then disconected the wires to the control. Then I took the old control off the board and inserted the new control. I attached the wire connectors to the new control and put the control panel back in place and fastened it with the scr
... Read more
ews. Last task was to replace the knob. The new control worked wonderfully with the first load of laundry. Piece of cake. Done in 5 minutes or less.
Read less
Was this helpful?
Thank you for voting!
In the spin cycle, drum would'nt spin unless assisted
22 of 24 people
found this instruction helpful.
-
ANTHONY from NY, NY
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
First off unplug the machine then turned off H/C water supply and removed hoses, laid the machine on its side, removed 3 motor supp. bolts, loosened drum pulled out shaft and clutch assembly was right there. Also replaced coupling while it was apart. And to think, a svce company wanted 179.00 just to walk in my door and diagnose the pblm.
... Read more
Then, parts and labor were extra. Thanks for the help/advice, piece of cake!!!!!!!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Cog stripped causing agitator to not turn
22 of 25 people
found this instruction helpful.
-
Vicki from Houston, TX
- Easy
- Less than 15 mins
-
Screw drivers, Wrench set
Removed top cap on agitator w/ flathead screwdriver. Removed protective cap over bolt and cog housing shaft. Used 7/16 deep socket w/ extension to remove bolt. Removed housing where stripped cogs were located. Cogs seated loosely in shaft housing no tools required to remove cogs. Replaced cogs in housing, made sure everything was lined co
... Read more
rrectly. re-inserted housing into shaft. ,screwed bolt, replaced caps and works like new.
Read less
Was this helpful?
Thank you for voting!
Top half of the agitator was not turning.
24 of 31 people
found this instruction helpful.
-
Dennis from Avon, NY
- Really Easy
- Less than 15 mins
-
Socket set
I just took the cap of the agitator off and the 3/8" nut was right there. I took it off with a socket, removed the top agitator, slid the assembled kit in , replaced the agitator and cap...that was it !!. These parts priced thrrough Sears were $77.00 plus S&H. Your price for the entire kit- less than $12.00 !! If you don't think that you
... Read more
can do this yourself, have your 7 year old child do it. Took me about 5 minutes. Great price and fast shipping. Thanks
Read less
Was this helpful?
Thank you for voting!
no cold water, Just hot
23 of 28 people
found this instruction helpful.
-
Jerry from Camarillo, CA
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers
I first removed the top panel,disconnected all the wire clips(four)and then removed the back panel
which is held in plsce by two bolts on the bottom and one plastic clip.After that i removed the solnoid
wires after marking them (hot and cold) the removed the hose clamp then removed the valve it self.Attached the new valve reconn ... Read more ected the hose and re attached the panels and now it works great.
which is held in plsce by two bolts on the bottom and one plastic clip.After that i removed the solnoid
wires after marking them (hot and cold) the removed the hose clamp then removed the valve it self.Attached the new valve reconn ... Read more ected the hose and re attached the panels and now it works great.
Read less
Was this helpful?
Thank you for voting!
latch switch was not working
28 of 43 people
found this instruction helpful.
-
John from BEAVER DAMS, NY
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
unfasten top from back, slide top forward and lift up, remove switch and cable (one piece), in stall new switch and cable, put top down and slide back, reinstall screws.
Was this helpful?
Thank you for voting!
Tub did not center and seal was hanging out of tub
22 of 25 people
found this instruction helpful.
-
James from Nelsonville, OH
- Easy
- 1- 2 hours
-
Pliers, Socket set
Laid washer on front side and removed top spring, then lifted the tub assembly to replace the right side spring, the one behind the motor was the hardest, I lifted the tub then removed the spring bracket at the tub with pliers and a socket. The top seal all I had to do was take the 4 screws that hold the top on (it takes a long extension)
... Read more
then sit it bak up and I lifted the top up to give me enough room to unsnap the top piece of the tub, cleaned it up put seal in. The parts fit perfitlt and real fast shipping, I bookmarked the site and will buy from again. JIM
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
The upper bearing in the gearcase became rusty & very noisy due to shaft seal leakage.
22 of 26 people
found this instruction helpful.
-
Craig from ANAHEIM, CA
- Really Easy
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set
Changing the gear case is a basic R and R operation since the gear case is a complete assembly riveted together. It is a bit challenging though getting to it because you have to totally disassemble the entire washer nearly every nut, bolt and screw. Fortunately the washer is fairly easy to work on and I am very mechanically inclined, but
... Read more
I did cheat a bit by watching some U-tube videos first. I couldn't find the same exact model washer as mine on U-tube but there were enough similar units to obtain the basic procedure. A thing I do when disassembling things is to take pictures of the way it's put together before removing stuff. It goes without saying that you first have to disconnect the power, the water hoses and it helps to get the washer out away from the wall so you can work around it. You have to remove the top, back panels, and the inner and outer tubs first. After removing the inner and outer tubs I turned the washer upside down in order to gain access to the gear case so I wouldn't have to stand on my head or lay down. Remove everything attached to the gear case (take picture) and use a strap wrench (or a strong friend) to hold the large pulley while removing the retaining nut. To remove the condenser (large round thing in black plastic retainer) rotate it counter clockwise and lift out, it doesn't snap out. I was very happy to see that the new gear case came with the shaft seal already installed so with a small amount of liquid dish soap around the outside of the rubber it allowed a nice slip fit back into the outer tub. All the parts that were removed pretty much will only fit one way so you don't have to worry too much about how everything goes back together. After reassembly and hooking up the washer again be sure to perform the calibration procedure before you turn on the water. Instructions came in the box with the gear case. Here is a side bar: I am 76, my grandson and I replaced the gear case in just a few hours, It's no big deal. Now for the interesting part, when I ordered the replacement gear case by the old part number I was told it had been superseded by a new number so when the new unit arrived I discovered that the shaft and seal looked different so hopefully the water leaking into bearing won't happen again. I was going to drill the old gear case apart and replace the bad bearing so I am glad I didn't because the shaft and seal would continue to leak and ruin the bearing again so don't try that. One thing I would like to mention about this company from which I ordered the part was the amazing delivery, only 36 hours. I ordered the part Sunday evening late and Tuesday morning early it arrived. Wow, blew me away, also I live in California and apparently the company is in Nova Scotia, no sales tax, Woo Hoo.
Read less
Was this helpful?
Thank you for voting!