110211 Kenmore Washer - Instructions

All Instructions for the 110211
91 - 105 of 522

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
heavy loads did not spin dry properly
6 of 8 people found this instruction helpful.
  • Chet from CLEARWATER, FL
  • Very Easy
  • Less than 15 mins
  • Screw drivers, Socket set, Wrench (Adjustable)
I followed the instructions provided by the video which I thought were spot on. Even to the size of the phillips screw driver.
Was this helpful?
Thank you for voting!
The original snapped due to it being plastic
5 of 5 people found this instruction helpful.
  • Davian from Pelion, SC
  • Very Easy
  • Less than 15 mins
Untwisted it and slipped the new one in quick and easily in less than a minute
Was this helpful?
Thank you for voting!
When the washer goes into a spin cycle, I would hear an intermittent loud clattering noise. I think the clutch teeth above (the cup part that is spring loaded) and the belted pulley's teeth below are not fully seating on each other during the spin cycle.
8 of 14 people found this instruction helpful.
  • TERRY from WAUKEE, IA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Socket set
W10721967 Splutch Cam Kit

Assuming the pulley nut was properly tightened at the factory. I think this problem occurs because of ever-so-slight rounding of the splutch cam teeth from the actuator engaging and disengaging over whatever time frame there is before a clattering noise develops.

When I took off the 13mm nut using the adjustable strap tool, it felt tight to me...Was it put on as tight as it should have been at the factory? Who knows. I don't have the torque specification of this nut on that plastic pulley.

Watch the videos to remove and replace the belt cover and belt, actuator and splutch cam kit.

Pay particular attention to tightening up the nut. I put the pulley on and hand-tightened the nut. I used the adjustable strap tool and before I tightened everything, I pushed up on the pulley to press against the spring pressure in order to mesh the teeth together. After the nut was tight, I repositioned the strap tool and gave it another go, further tightening it. You see earlier that day, I only tightened it up once because I thought it was good and tight. I put everything back and within a half-hour it was clattering again and I could loosen the nut I thought was tight by hand! I fooled myself. That's why I did it twice, and don't be afraid to give it a good second tightening effort. Two weeks now and the wife is currently very happy.
Was this helpful?
Thank you for voting!
Washer was out of balance on spin cycle
5 of 5 people found this instruction helpful.
  • Charles from Grizzly Flats, CA
  • Easy
  • 1- 2 hours
  • Pliers
I do not know much about washer repair and after watching how to replace the suspension rods I decided it was not as difficult as I thought. I replaced the suspension rods and springs and that fixed the problem. The price for parts was reasonable and I received my parts in 2 days.
Was this helpful?
Thank you for voting!
Loose pulley
7 of 11 people found this instruction helpful.
  • Joseph from BAKER, FL
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Tightened up the pulley as the video showed me that might be the issue.
Was this helpful?
Thank you for voting!
The washer stopped draining.All the pump motor did was hum.
5 of 6 people found this instruction helpful.
  • Michael from Staten Island, NY
  • Easy
  • 1- 2 hours
  • Pliers, Socket set
I drained the machine and pulled it away from the wall.Then I disconnected the drain hose and removed the back panel.Next,I removed the three screws holding the pump in place and disconnected the power plug from the motor.I then removed the short drain hose from the pump.Installation was the opposite of the removal sequence,and the machin e worked fine right after I was done.The new part was identical the the old one,and the job was a snap.
Was this helpful?
Thank you for voting!
Making a loud noise for a while then stopped spinning
4 of 4 people found this instruction helpful.
  • Lucas from ARKANSAS CITY, KS
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Wrench set
Removed two screws to remove guard. Two screws to remove another part with wires. Pulley nut was already missing. Component was twist locking tabs.
Was this helpful?
Thank you for voting!
The washer was vibrating very bad on large loads
4 of 4 people found this instruction helpful.
  • Mark from SAINT CLOUD, FL
  • Very Easy
  • 30 - 60 mins
  • Screw drivers
Using the parts I ordered and following the instructions provided in the video from partselect.com made the repair very easy and solved the problem
Was this helpful?
Thank you for voting!
Lid wouldn't lock
4 of 4 people found this instruction helpful.
  • James from INDIAN LAKE, NY
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Removed 5 screws on back, released 2 retention clips on front, lifted top of washer to expose lock assembly, removed 2 screws holding lock assembly in place followed electrical line back to plug behind control panel plugged new lock in, and reassembled in reverse order. Done!
Was this helpful?
Thank you for voting!
Water would not stop running over filled the washer
4 of 4 people found this instruction helpful.
  • Mary from GROVER HILL, OH
  • Very Easy
  • 30 - 60 mins
  • Socket set
Unplugged the washer turned off the water disconnected the water lines then took the cover off and disconnected the wires and took 2 screws out and took the old part out and put the new 1 in
Was this helpful?
Thank you for voting!
tub motor shot
5 of 7 people found this instruction helpful.
  • melanie from GREENFIELD, IN
  • Really Easy
  • 30 - 60 mins
Please check the order was refused so I would not have to pay to ship back. The lady I spoke to on the phone said to do it this way. I have been TRYING to call for 2 weeks but no one is answering the phone due to CV19!!
The order is back at your warehouse. Please give me my refund!! Plus I have emailed your CS dept. numerous times wi th NO answer, only automated.
Was this helpful?
Thank you for voting!
Wouldn't agitate
4 of 4 people found this instruction helpful.
  • HOWARD from MIMBRES, NM
  • Really Easy
  • 30 - 60 mins
  • Socket set
Removed lid panel changed lid lock switch. Took cap off removed 7/16 bolt changed out thrust spacer and agitater repair kit. Took about an hour.
Was this helpful?
Thank you for voting!
making noise when starting spin cycle
4 of 5 people found this instruction helpful.
  • JERRY W. from CARROLLTON, GA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Watch video on the site and the insulation will be easy and take about 30 min.
Was this helpful?
Thank you for voting!
The washer would walk across the floor
4 of 5 people found this instruction helpful.
  • William from BROOKFIELD, WI
  • Very Easy
  • 30 - 60 mins
  • Socket set
Watched the video. It was by far the easiest repair I've ever done. The washer is happy and stays in it place
Was this helpful?
Thank you for voting!
screeching noise at times,Wouldn't spin out
4 of 5 people found this instruction helpful.
  • Jerry from LENGBY, MN
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Tip washer on its front removed belt guard and belt. Removed shift actuator. Put new actuator on, put belt and guard back on, put back panels on and it was fixed.
Was this helpful?
Thank you for voting!
All Instructions for the 110211
91 - 105 of 522