110211 Kenmore Washer - Instructions

All Instructions for the 110211
61 - 75 of 522

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Top section of the agitator would not work properly
12 of 20 people found this instruction helpful.
  • James from Crownsville, MD
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Removed the top cap, unbolted the agitator, lifted off the top section, removed old "dogs" and replaced new "dogs", reinstalled agitator and tested.
Was this helpful?
Thank you for voting!
With full load, clothes were not agitating correctly - very little action or movement of the upper agitator section.
8 of 8 people found this instruction helpful.
  • Douglas from Lancaster, CA
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Took off softener dispenser, pried off top of agitator, removed bolt from top of agitator.

Then pulled out the agitator assembly for easier access.

Used screwdriver to brake small plastic keepers holding secondary agitator ratchet clutch to the secondary agitator.

Assembled and inserted new ratchet mechan ism in the top of the agitator, making sure 4 small square pegs protruding from the end of the new assembly fully entered into mating holes on the secondary agitator.

Placed the agitator back on the agitator post and installed and secured bolt. Replaced cap and installed softener dispenser.
Was this helpful?
Thank you for voting!
replaced drain hose that was missing
12 of 20 people found this instruction helpful.
  • Delmar from EAST TROY, WI
  • Really Easy
  • 30 - 60 mins
  • Pliers
slipped the new drain hose on and with locking plyers slipped the wire clap in place after three trys
Was this helpful?
Thank you for voting!
Never recieved
8 of 9 people found this instruction helpful.
  • Nick from LUTHER, OK
  • Very Difficult
  • Less than 15 mins
Ordered this part 3 times over a period of several months and never received it. Only would get emails saying it was out of stock and would be sent soon. Eventually had to but a whole new washer. Will never recomend this company or another Maytag product.
Was this helpful?
Thank you for voting!
washer is unbalanced during a spin cycle
7 of 7 people found this instruction helpful.
  • Tiffany from NORTH OLMSTED, OH
  • Really Easy
  • Less than 15 mins
I watched a video on you tube before making the repair, there was only one bad rod support, location right rear, I recommend watching a video on you tube first, it is very simple to change, however the replacement of the part was not the solution to the unbalanced load during the spin cycle, so I guess I have some research to do.
Was this helpful?
Thank you for voting!
Washer was stuck on rinse cycle
8 of 10 people found this instruction helpful.
  • Michael from HARWICH PORT, MA
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Research showed it was the transmission and the actuator . Parts were super easy to install and it solved the issue 100%

PS - I put some light lithium grease on the transmission and it’s quieter than it was when new
Was this helpful?
Thank you for voting!
Would not start to spin on spin cycle.It would just make a clicking sound
7 of 7 people found this instruction helpful.
  • Anthony from LYLE, MN
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Tipped washer on its back & tookold Washer pulley assembly off & put new one on.
Was this helpful?
Thank you for voting!
Shaking extreme
7 of 7 people found this instruction helpful.
  • Barbara from RICHMOND, IN
  • Really Easy
  • 15 - 30 mins
  • Socket set
Per instruction sent with purchase
Was this helpful?
Thank you for voting!
washer wasn't spinning after rinsing but the motor was running
8 of 10 people found this instruction helpful.
  • Terry from HANCOCK, MD
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
I had taken the time to watch videos of this repair so when the switch arrived I knew what I had to do. Removing the screws to get the back cover off was simple as was installing the switch. No tricks here just watch the videos and your all set to do the job
Was this helpful?
Thank you for voting!
I followed the video guide, which was excellent
7 of 7 people found this instruction helpful.
  • Richard from NAPLES, FL
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver
I followed the instructions, however I did not have a spot to hold the bar temporarily, so I drilled a hole in the corner frame to hook them in at the front of the machine. All else was easy and according to the video.

Machine works great now.
Was this helpful?
Thank you for voting!
When washer would go into spin cycle it would shake violently. This also prevented the spin cycle from completing leaving clothes soaked
7 of 8 people found this instruction helpful.
  • Jonathan from NEW BRAUNFELS, TX
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Followed videos sent with the repair items. It was very easy and solved my issue. My washer did not have the centering springs to begin with so I was unsure if I even needed them. But after replacing all the suspension rods and adding the pack of centering springs this has solved my issues
Was this helpful?
Thank you for voting!
The light set assembly was down to one light. So we needed to order one
7 of 8 people found this instruction helpful.
  • Suzanne from SPRING HILL, FL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
The repair went really well. And it was the right part and now we can have light in our fridge.
Thank you!
Your help and fast shipping really made a difference. I will always shop for my parts with you guys. Thank you for having things no store has. It saves alit of money all around.
Thank you again.
Was this helpful?
Thank you for voting!
top agitator would not operate
8 of 11 people found this instruction helpful.
  • Larry from Edgewood, TX
  • Really Easy
  • Less than 15 mins
  • Socket set
unscrewed a bolt, pulled top agitator out and replaced parts and reinstalled.
Was this helpful?
Thank you for voting!
Making noise when spinning tub hit side of washer.
7 of 8 people found this instruction helpful.
  • Ernestine from CARRIERE, MS
  • Really Easy
  • 30 - 60 mins
  • Socket set
Remove top of washer suspension
Rod goes on side of tub .
Was this helpful?
Thank you for voting!
washer wasn't spinning on final spin
7 of 8 people found this instruction helpful.
  • Terry from HANCOCK, MD
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
First I found and reviewed videos on line to do the repair for my machine and when I actually did it the videos made it simple to do. Always look for videos of the installation for your machine or appliance and the job will go easy
Was this helpful?
Thank you for voting!
All Instructions for the 110211
61 - 75 of 522