110211 Kenmore Washer - Instructions

All Instructions for the 110211
76 - 90 of 522

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washer gets stuck on Rinse and not complete the cycle.
6 of 6 people found this instruction helpful.
  • Charles from SEALY, TX
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Found common diagnosis and instructions on internet. It is not difficult to replace.
Unfortunately, this new latch assembly did not fix the problem.
Was this helpful?
Thank you for voting!
Washer would not agitate
6 of 6 people found this instruction helpful.
  • Lee from FORT WORTH, TX
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
When to PartSelect Web site, used their trouble shooting guide, Used their advice, which was to replace the actuator. bought and installed the actuator which took around 20 minutes or so. washer started working fine after replacing. Thanks to the website I save a lot of money. Thanks PartSelect
Was this helpful?
Thank you for voting!
Rotation cogs (4) worn out and the upper part of the agitator wouldn't turn with the lower agitator.
6 of 6 people found this instruction helpful.
  • David from LOVELAND, CO
  • Really Easy
  • 15 - 30 mins
  • Socket set
Popped the cap off the agitator (pocket Knife) Look down in the center of the agitator. I saw I needed a 7/16 socket, 6" extention and ratchet. I used 1/4" drive. I took the retaining bolt out and lifted the upper portion of the agitator off of the iower portion and out of the tub. Set the part I took out on the dryer. I pulled the cone s haped part that houses the 4 cogs pieces out of the center of the upper agitator part. Once the coned shaped part was out, turned it upside down and placed it on the closed washing machine lid, then again used my pocket knife to lift the plastic retaining ring that securely holds the 4 cogs in place upward on the cone as to remove and replace the 4 worn out cogs with the new ones purchased in a repair kit. Pay close attention the direction the old cogs are facing, so the new ones go back in the same facing direction. It can be extremely easy to install the new ones backwards. I have to say at this point, I was quite disappointed with the retrofit repair kit I purchased. The new cone part the holds the cogs and goes down into the center of the upper agitator wouldn't allow the bolt that locks the whole agitator to the shaft to line up straight and wanted the bolt to "cross" thread into the main shaft. I took it all apart again and reused the original coned shaped part that came with the machine. I should have purchased just the 4 cogs for considerably less money. Reassembled the cone part and put it back together. Reinstalled the upper agitator in reverse order of removing it. Turned on the washer and it works like it's supposed to once again. Hope this helps the next person.
Was this helpful?
Thank you for voting!
The wash cycle made a loud grinding noise when it went from filling to wash.
6 of 6 people found this instruction helpful.
  • Angelo from PORTLAND, ME
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set, Wrench (Adjustable)
I put the dial to drain and and pressed the pause button for 3 seconds and it drained.
Unplugged the washer from the electrical outlet .
Shut the hot and cold water off. Disconnected and drained them.
Placed the washer on a soft mat on front side exposing the back and bottom of the machine.
Unscrew the metal cover wi th Philips head screw driver.
Disconnect the drain hose to a bucket or small dish tub .
Remove the belt cover with 5/8 ratchet or wrench.
Using a ratchet or wrench remove the one bolt holding the clutch in place .
Remove the two Philips head screws from the shift mechanism ( looks like clock timer,my memory is failing me right now sorry! ) .
Pull down on bottom gear after removing nut.
Push in and pull down with a flat head screwdriver on the tabs holding the collar in place above the top gear .The collar and gear and spring should come apart.
Install new parts in the same order . Reassemble make sure to use Locktite 242 on the bottom nut holding the gear.
Install belt , belt guard , cover drain hose . Stand machine back up , reconnect all hoses tightly plug machine into electrical outlet and start. Put a smile on your face because you did a great job and saved yourself some money!
Was this helpful?
Thank you for voting!
Suspension rods were worn; washer is 10+ years old
7 of 9 people found this instruction helpful.
  • William from NAPERVILLE, IL
  • Easy
  • More than 2 hours
  • Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Replaced the suspension rods, suspension rod supports, main drive belt, tub centering springs, water supply hoes, and washer drain hose. Taped new front suspension rods to side of tub to ensure that they did not slide down when raising the washer off its back from the floor. Had a helper lift the tub, which made attaching the new suspensi on rods easy. The tub is extremely heavy so by a helper lifting it up it made attaching the new suspension rods much easier. IMPORTANT: According to the technician's manual, which was taped to the inside of the washer, it is absolutely necessary to recalibrate the washer after replacing any suspension parts. We did this by following the instructions in the tech manual. Failure to recalibrate a washer could result in poor performance. The procedure is different for each brand or model of washer, but again is absolutely essential after replacing suspension parts of any kind. For some unknown reason, our washer did not have the tub centering springs. Our model should have had the springs.Facing the washer, we attached one to the front left tub housing and one to right rear of the tub housing. Recommend that anyone watch the installation videos for the suspension rods, center springs, and main drive belt before attempting the repairs.
Was this helpful?
Thank you for voting!
Lid lock/latch stuck closed
6 of 7 people found this instruction helpful.
  • David from BELMONT, MI
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
Watched a video
Was this helpful?
Thank you for voting!
Dripping water inlet valve
6 of 7 people found this instruction helpful.
  • Bokus, from Normal, IL
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Prepare:
Before you start turn off the hot and cold water supply. Then remove the supply lines from the back of the washer. You may want a bucket to catch any remaining water in the supply lines.

Replace water inlet valve:
First, remove screws from upper back plate to release the control panel and the washer top. ... Read more />
Second, slide washer top to the front of the washer about 1/2 - 1 inch. This will allow you to raise the washer top.

Third, from underneath the washer top release the control panel by disengaging the locking clips near the back of the control panel.

Fourth, lay the top back in to the forward position and hinge the control panel from back to front. This will release the control panel.

Fifth, Disengage the wire harness for the control non. And remove the control panel completely.

Sixth, remove the wiring harness from the water inlet valve located on the left hand side, the. Remove the screws holding the valve in place.

Seventh, Install new valve, reconnect all of the wiring harnesses, reconnect the control Bob wire harness, and reinstall the control panel. It should click into place just as it came out.

Eighth, Slide the washer top back into place. Reinstall the back plate and screws.

Finish:
Finally reinstall the supply lines and turn on the water.
Was this helpful?
Thank you for voting!
Gear stripped on main spline
6 of 7 people found this instruction helpful.
  • Bernard from ARIZONA CITY, AZ
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Followed detailed instructions which were supplied with the parts. It was easy and my machine is working great with no issues. Also I just didn’t get the main drive pulley, all new parts came for the bottom end, great service and excellent parts.
Was this helpful?
Thank you for voting!
Noise, grinding
7 of 10 people found this instruction helpful.
  • Craig from MURFREESBORO, AR
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set, Wrench set
Following what the video shows how that they send with your part email, confirmation or receipt!! Easy Peasy!!
Was this helpful?
Thank you for voting!
I cross threaded the cold water hook up to the washer
9 of 16 people found this instruction helpful.
  • Steven from Fall City, WA
  • A Bit Difficult
  • 1- 2 hours
  • Wrench set
If you take the back off the machine, it's a lot easier to detach the control bridge. Saved a lot of time and did not need to stretch your fingers
Was this helpful?
Thank you for voting!
Washer won’t go into spin cycle! Tries too but then stops
5 of 5 people found this instruction helpful.
  • Dawn from TOWANDA, PA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Replaced the drive belt and shift actuator but that did not fix the problem! So I ordered a transmission and this still did not fix it! I give up! Time to get a new washer!
Was this helpful?
Thank you for voting!
Water inlet valve leaking
5 of 5 people found this instruction helpful.
  • Shaun from Cardiff by the Sea, CA
  • Very Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Turn off water and remove inlet hoses
Remove of control Tower
Remove control tower and unplug from rest of washer
Remove water inlet valve and install new valve
Reverse operations
Was this helpful?
Thank you for voting!
Washer wasn't agitating.
5 of 5 people found this instruction helpful.
  • Darryl from Danville, PA
  • Very Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
First, this is the second time the transmission actuator went bad. The first-time washer was still under warrenty and I watched the tech replace it. This time warranty has expired and I'm mechanically inclined, so I ordered the part. Replacing was easy, unplug, tip washer up so you can get under it, remove plastic guard (two hex nuts) and remove actuator by removing two screws. Reverse procedure to install new actuator. The only caution I will say is when tipping washer if you have a wall to lean it against, perfect, just put something under it for saftey so it can't fall on you.
Was this helpful?
Thank you for voting!
washing machine stuck on drain cycle
17 of 41 people found this instruction helpful.
  • Matthew from Wauwatosa, WI
  • Easy
  • 15 - 30 mins
  • Screw drivers
Siphon break kit keeps washing machine from continuing to siphon after rinse/cycle -- like emptying a pool with a hose. Fixed the problem of the tub never filling due to siphon draining out water as it's being put in.
Was this helpful?
Thank you for voting!
water would drip into tub between uses
5 of 5 people found this instruction helpful.
  • Dale from MANDAN, ND
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Unplugged washer, turn off water to washer, removed water lines from washer, pull washer away from wall, removed about 5 screws from top access panel and remove, used putty knife to release clips from both sides of front control panel and lay forward, removed three screws from valve, disconnect hose from valve. Reassemble in reverse order . Not a bad idea to run a little water into bucket from both supply line to remove any foreign material that may have let lose from shut off valve before reconnecting to washer.
Was this helpful?
Thank you for voting!
All Instructions for the 110211
76 - 90 of 522