110211 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Banging all the time during rinse as if its out of balance
14 of 18 people
found this instruction helpful.
-
christine from SWANSEA, MA
- Really Easy
- 30 - 60 mins
-
Screw drivers
Followed the video, no need to add. Worked perfectly!
Other Parts Used:
Was this helpful?
Thank you for voting!
lid would not lock, washer would not run...
12 of 13 people
found this instruction helpful.
-
John from Hale Center, Texas, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed old striker ( 2 Phillips head screws ) replaced with new striker with the 2 screws and was done, easy fix...
Was this helpful?
Thank you for voting!
Water inlet nozzle was stripped and leak
24 of 50 people
found this instruction helpful.
-
Armand from WESTPORT, MA
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Remove the front panel and back panel unplug the part unscrewed the part and replace it with the new one
Was this helpful?
Thank you for voting!
door striker prongs snapped off
11 of 12 people
found this instruction helpful.
-
robert from NASHUA, NH
- Very Easy
- Less than 15 mins
-
Screw drivers
The door strike part was very simple to remove. 15 seconds at most...Part ordered and delivered a day early. Install of new part was again about 15 seconds and Wala....job completed. Thanks for the great service....will call again when needed....
Was this helpful?
Thank you for voting!
Scratches in Surface
83 of 228 people
found this instruction helpful.
-
Michelle from Richardson, TX
- Really Easy
- Less than 15 mins
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this helpful?
Thank you for voting!
Darn thing hadn't "Agitated" for about 10 years!
11 of 13 people
found this instruction helpful.
-
Stephen from Cornwall, NY
- Easy
- Less than 15 mins
-
Pliers
After removing the bolt (7/16" head), and using a pair of pliers to remove the 3-4 in deep "cup", it was immediately obvious how to assemble the new cup and pawls (ratchets).
Orienting the black "bearing" was not so obvious, but on closer inspection of the illustration, it became clear. The four "ears" of the bearing go clos ... Read more est to the pawls. The little tabs that are co-planar to the ears fit into the four grooves of the new cup.
And here's the trick (besides making REALLY, REALLY SURE how the pawls orient)--Soak the black bearing piece in hot water to soften it up, and let it slide over the cup better. If you don't, you risk breaking it. If you do, it slides over and "clicjs" into place, with the ears resting right against the bottom lip of the cup, capturing the pawls.
Installation back into the washer is obvious.
The thing works like a charm! It hasn't worked this well for a decade!
Orienting the black "bearing" was not so obvious, but on closer inspection of the illustration, it became clear. The four "ears" of the bearing go clos ... Read more est to the pawls. The little tabs that are co-planar to the ears fit into the four grooves of the new cup.
And here's the trick (besides making REALLY, REALLY SURE how the pawls orient)--Soak the black bearing piece in hot water to soften it up, and let it slide over the cup better. If you don't, you risk breaking it. If you do, it slides over and "clicjs" into place, with the ears resting right against the bottom lip of the cup, capturing the pawls.
Installation back into the washer is obvious.
The thing works like a charm! It hasn't worked this well for a decade!
Read less
Was this helpful?
Thank you for voting!
squeal and chirping while in risne / spin mode
10 of 10 people
found this instruction helpful.
-
Thomas from GRAIN VALLEY, MO
- Really Easy
- 30 - 60 mins
-
Nutdriver
Removed belt cover from bottom of the transmission , remove old belt, clean the pulleys ,and re install new belt. The new belt fits tighter so it did a few time to get the belt fully seated. Re install belt cover.
Was this helpful?
Thank you for voting!
Top half of agitator wasn't moving
10 of 11 people
found this instruction helpful.
-
Debra from Orange, CA
- Really Easy
- Less than 15 mins
-
Socket set
First, I wrestled off the top cap of the agitator. Then, I unscrewed the bolt and took out the cam. I noticed that the agitator dogs were worn smooth. I replaced them, put it all back together and VOILA! I bought the whole agitator kit, not knowing what I was going to find, because I wasn't a Magtag repair woman. It ended up that the cam
... Read more
that came in the kit was too big for my washer anyway. Luckily, all I needed was 4 plastic dogs. The price of the whole kit was so inexpensive anyway, it was no big deal. Especially because, I was looking to buy a new washer or a big repair bill. This website is great! Thank you.
Read less
Was this helpful?
Thank you for voting!
Hot water valve would barely open - take 35 mins to fill washer
10 of 11 people
found this instruction helpful.
-
Kevin from ARLINGTON, TX
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
Pull the washer out from wall
Unplug the Washer
Close the supply line valves
Unscrew the supply lines, use bucket to catch line water
Remove 1 cover plate for elec lines (1 screw)
Remove 2 screws on edge of back plate for control panel
Slide long blade under front of control panel corners, pop the lock clips< ... Read more br />Lay control panel forward - controls down
Compare new and old part - looks the same, wires, etc
Remove center screw on back plate cover to remove it
Unplug the elec wires connecting the valves and the control panel
Remove 2 screws holding the water valve outlet
swap out the old values for new valves
Reverse the process - step backwards and reassemble
Took me 36 minutes.
Tested the washer for Hot fill and later cold - both work
Unplug the Washer
Close the supply line valves
Unscrew the supply lines, use bucket to catch line water
Remove 1 cover plate for elec lines (1 screw)
Remove 2 screws on edge of back plate for control panel
Slide long blade under front of control panel corners, pop the lock clips< ... Read more br />Lay control panel forward - controls down
Compare new and old part - looks the same, wires, etc
Remove center screw on back plate cover to remove it
Unplug the elec wires connecting the valves and the control panel
Remove 2 screws holding the water valve outlet
swap out the old values for new valves
Reverse the process - step backwards and reassemble
Took me 36 minutes.
Tested the washer for Hot fill and later cold - both work
Read less
Was this helpful?
Thank you for voting!
Washer wouldn't start - Flashing Lid Light
13 of 20 people
found this instruction helpful.
-
Marc from HOPE MILLS, NC
- Easy
- 30 - 60 mins
-
Screw drivers
I checked out the reviews and the recommendation of these "professionals", replaced the part easy enough when it came in. However, it didn't solve the problem. Got an actual professional to come in and see what the problem was, and they determined that gear oil was being leaked and it wasn't worth replacing.
Tried to get a re ... Read more fund and return the part. Was told absolutely not. The money back guarantee is a lie.
Tried to get a re ... Read more fund and return the part. Was told absolutely not. The money back guarantee is a lie.
Read less
Was this helpful?
Thank you for voting!
washer would not fill, all 4 valve solenoid checked good.
12 of 17 people
found this instruction helpful.
-
Dewey from BURKBURNETT, TX
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
The valve is a 4 solenoid valve, which has Temp. sensor molded into the valve body mixer center outlet. No mention of it in the troubleshooting. it has a 2 pin plug. it was shorted zero ohms.
New one measure open infinity. I also purchased the control module as the troubleshooting said to if solenoid checked good which all 4 rea ... Read more d 1310 ohms , i purchased and replaced control module, no help. the guide is outdated for these new high tech washers. If this happens again. I will just unplug the 2 pin plug on bottom of valve assembly. By the way the 2 clips that hold the washer top in place are very difficult to remove and re install.
New one measure open infinity. I also purchased the control module as the troubleshooting said to if solenoid checked good which all 4 rea ... Read more d 1310 ohms , i purchased and replaced control module, no help. the guide is outdated for these new high tech washers. If this happens again. I will just unplug the 2 pin plug on bottom of valve assembly. By the way the 2 clips that hold the washer top in place are very difficult to remove and re install.
Read less
Was this helpful?
Thank you for voting!
Error that Door was not closed
10 of 12 people
found this instruction helpful.
-
Don from BROWNSBORO, TX
- Very Easy
- Less than 15 mins
-
Pliers
Using a pair of pliers turn counter clockwise to remove broken part. Install the new part by turning clockwise. Soooo easy with install time of less than a minute.
Was this helpful?
Thank you for voting!
The main knob insert snapped.
11 of 16 people
found this instruction helpful.
-
Larry from HICKORY, NC
- Very Easy
- Less than 15 mins
Nothing to it. Just remember to put the insert in the knob, NOT on the selector stem. Line up the flat part of the insert with the flat part of the stem and push the knob in place.
Don NOT ram it on the selector stem. When it's seated, don't push any more. That's all there is to it. It works. If the pointer on the knob indicat ... Read more es the selector is lined up correctly, but it isn't, the problem is the selector, not the knob.
Don NOT ram it on the selector stem. When it's seated, don't push any more. That's all there is to it. It works. If the pointer on the knob indicat ... Read more es the selector is lined up correctly, but it isn't, the problem is the selector, not the knob.
Read less
Was this helpful?
Thank you for voting!
wash machine walked
9 of 10 people
found this instruction helpful.
-
Elzoria from FROSTPROOF, FL
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers
watch utube instruction.easy repair
Was this helpful?
Thank you for voting!
Wouldn’t drain pump made loud noise
10 of 13 people
found this instruction helpful.
-
REED from BUCHANAN, NY
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Wrench (Adjustable)
Removed old drain pump and found a sock in the inlet - must have burned out pump because after removing it pump was still defective. Installed new pump in about 30 minutes and off to the races no more issues
Was this helpful?
Thank you for voting!