110211 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
washer would not spin on wash cycle
3 of 3 people
found this instruction helpful.
-
Kim from MOUNT UNION, PA
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
My daughter is the handy one in the family. She followed Steve's video installation steps and in an hour i was washing clothes.
Was this helpful?
Thank you for voting!
nut loosened from pully, belt cut into shield and came off
3 of 3 people
found this instruction helpful.
-
Roland from SPRINGTOWN, TX
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
removed shield and pully nut and replaced shifter pulley and belt.
rolled it around several times to see how it stayed on or not, it stayed
. I replaced the new shield put the washer upright and tested fine.
rolled it around several times to see how it stayed on or not, it stayed
. I replaced the new shield put the washer upright and tested fine.
Other Parts Used:
Was this helpful?
Thank you for voting!
Washer was making an awful screeching noise when agitating
3 of 3 people
found this instruction helpful.
-
Kristy from Lebanon, NJ
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
I turned off and disconnected the water lines (have a bucket ready) and tipped the washer on its back. I followed along with the provided video that was super helpful. Disconnecting, moving the washer, and reconnecting everything took longer than the repair. Very satisfied with this repair!
Was this helpful?
Thank you for voting!
Actuator clicking not going into spin mode
3 of 3 people
found this instruction helpful.
-
Courtney from Hollis, NH
- Easy
- 30 - 60 mins
-
Pliers, Socket set
I laid the washer on its front side to access underneath. I removed the original washer pulley system and actuator very easily to replace them with the new parts. The new/updated model actuator for my machine was a little bit challenging to maneuver around existing parts to make work, but I eventually got it installed. The plug was angled
... Read more
very differently than the original plug on the actuator, but it was a tight fit. There was no issue installing the washer pulley system. Hooked washer back up to power, water lines, drain line, and the washer has been working perfectly since.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Washer -Maytag Centennial- would NOT agitate. It would run through all cycles as indicated by the lights and even spin at the end, but never agitated. It also did not appeared to go into "sensing" mode at the start. Took a long time to move from "sensing" light to "wash" light. Did not hear or see a
3 of 3 people
found this instruction helpful.
-
Maxwell from RINGWOOD, NJ
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
There are a number of videos showing how to do this repair:
>Disconnect power and water - cold, hot and drain.
>Put washer on its side on a stand (low platform) to get to the bottom.
Better than than just laying front of washer on floor.
>Used a drop light to help see bottom.
>Removed Pulley Cover using nut dri ... Read more ver - has 2 screws with nut
heads.
>Removed and replaced the Shift Actuator (part provided) using a
Phillips screw driver - 2 green screws. Unplugged electrical
connector which should be reconnected before new unit is screwed
back down.
Replacement part is not the same as the original. From what I read.
this part has been a problem with these washers.
>Put Pulley Cover back on.
>Reset washer upright.
>Reconnected water and power.
>Ran "CALIBRATION". In Diagnostic Test Mode, turned to "rinse"
light on and pushed "start" button.
>Ran "AUTOMATIC TEST". In Diagnostic Test Mode, turned to "spin"
light on and pushed "staet" button. Washer agitated in first cycle
- "sensing" and in "wash".
.
Washer has been working as it should and I a very happy with the results.
I must say that PartSelect Identified the bad part as the Shift Actuator right off from the symptoms I provided.
>Disconnect power and water - cold, hot and drain.
>Put washer on its side on a stand (low platform) to get to the bottom.
Better than than just laying front of washer on floor.
>Used a drop light to help see bottom.
>Removed Pulley Cover using nut dri ... Read more ver - has 2 screws with nut
heads.
>Removed and replaced the Shift Actuator (part provided) using a
Phillips screw driver - 2 green screws. Unplugged electrical
connector which should be reconnected before new unit is screwed
back down.
Replacement part is not the same as the original. From what I read.
this part has been a problem with these washers.
>Put Pulley Cover back on.
>Reset washer upright.
>Reconnected water and power.
>Ran "CALIBRATION". In Diagnostic Test Mode, turned to "rinse"
light on and pushed "start" button.
>Ran "AUTOMATIC TEST". In Diagnostic Test Mode, turned to "spin"
light on and pushed "staet" button. Washer agitated in first cycle
- "sensing" and in "wash".
.
Washer has been working as it should and I a very happy with the results.
I must say that PartSelect Identified the bad part as the Shift Actuator right off from the symptoms I provided.
Read less
Was this helpful?
Thank you for voting!
water inlet valve stopped working
3 of 3 people
found this instruction helpful.
-
Zoran from ROCKVILLE, MD
- Really Easy
- 1- 2 hours
-
Pliers, Screw drivers, Wrench (Adjustable)
used the Parts.com video. I am not mechanical at all, but removed the old part and installed the new part without a hitch. Very happy.
Was this helpful?
Thank you for voting!
Top section of agitator was slipping.
3 of 4 people
found this instruction helpful.
-
Stephen from Hot Springs, AR
- Really Easy
- 15 - 30 mins
-
Nutdriver
I ordered the new cogs but didn't want to wait the few days for them to arrive. So I decided to try and temporarily repair the old ones. After looking at the picture of the new ones on this site I realized that the teeth were just worn down. I took all four of them out and used a grinding disc to carve the teeth down deeper. They were not
... Read more
perfect. (I would recommend holding the teeth with a vise.) However, after reinstalling the cogs the machine worked perfect and that was two weeks ago. I'm not going to install the new ones until I have to.
Read less
Was this helpful?
Thank you for voting!
Door strike broke.
3 of 4 people
found this instruction helpful.
-
Derrick from WILSON, NC
- Very Easy
- Less than 15 mins
It easily installed with a twist lock removal and installation. 2 minute fix.
Was this helpful?
Thank you for voting!
Needed to extend drain hose to reach drain
3 of 4 people
found this instruction helpful.
-
Emmett from WEATHERFORD, TX
- A Bit Difficult
- More than 2 hours
-
Socket set
Ordered drain hose extender. It uses a rubber flange with hose clip to attach to washer's plastic hose. When tightened, the hose clip crushes the plastic hose and crimps it, causing a leak. My solution was to find a copper pipe flange that was the same diameter as the interior of the plastic hose to act as a bushing for the plastic hose.
... Read more
The hose clip could then be tightened without deforming the hose. Worked great with no leaks.
Read less
Was this helpful?
Thank you for voting!
Agitator not moving
2 of 2 people
found this instruction helpful.
-
Kevin from ALBUQUERQUE, NM
- Very Easy
- Less than 15 mins
-
Socket set
Half inch extension. Removed plastic set piece. Remove agitator cap. Remove ring remove worn cogs. Replaced new cogs Replace lock ring, back together. 10 minutes
Was this helpful?
Thank you for voting!
Agitator cogs all broken
2 of 2 people
found this instruction helpful.
-
Kelly from AMARILLO, TX
- Very Easy
- Less than 15 mins
-
Socket set
Removed Softner dispenser and cap. With a 3/8" socket wrench and extension And 7/16" socket I took out the screw holding the agitator and removed top section of agitator. Turned upside down and removed the rubber grommet that holds the cogs in place. Replaced cogs and reinstalled grommet. Aligned top part of agitator with 2 tabs and put b
... Read more
ack in place and secured with 7/16" screw. Replaced cap And dispenser. Good to go. Works perfectly. Very easy repair.
Read less
Was this helpful?
Thank you for voting!
Washer not agitating
2 of 2 people
found this instruction helpful.
-
Dianne from WALES, MI
- Very Easy
- Less than 15 mins
-
Socket set
Washer was not agitating. My husband did not have a clue what to look for, but he took it apart and noticed two of the four directional cogs were stripped. Did an internet search and found the part on your website and thought we would give it a try since the part/shipping was under $20. The parts came in three days and my washer lives
... Read more
on. Was ready to get a new one since it is 18 years old, but I will not wait. Excellent website with all instructions and parts breakdown of the washer.
Read less
Was this helpful?
Thank you for voting!
Washer would not adgitate
2 of 2 people
found this instruction helpful.
-
Joe from SAN JOSE, CA
- Very Easy
- Less than 15 mins
-
Nutdriver
I ordered a lid switch because the washer wouldn't agitate. Most reviews indicated that was the problem. While waiting for the part to arrive, I discovered the transmission to be of fault.I let parts select know that I no longer needed the part. Parts Select gave me an immediate refund no questions asked and before I returned the part to
... Read more
them. That is customer service!! I will use Parts Select for all my future purchases. I can trust a company that trusts its customers.
Joe M. San Jose
Joe M. San Jose
Read less
Was this helpful?
Thank you for voting!
Would not Agitate
2 of 2 people
found this instruction helpful.
-
Scott from HILBERT, WI
- Very Easy
- Less than 15 mins
-
Screw drivers
Tip the washer on its back remove the agitator install new one under 15 minutes
Was this helpful?
Thank you for voting!
Agitator seperated from inside of wash drum
2 of 2 people
found this instruction helpful.
-
Larry from Brandon, FL
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
I had to find a point of reference first since item came apart in wash cycle and internal pieces fell out - thank goodness for YOUTUBE. Another guy was thoughtful enough to do a video on how the assembly came apart / went back together - a huge help for sure. Actual repair was less than a half hour after obtaining new part and seeing vi
... Read more
deo. The 12 year old washer works like brand new - saving me close to 1,000 dollar replacement charges.
Read less
Was this helpful?
Thank you for voting!