- Home
- 11020022013
- Instructions
11020022013 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Agitator stopped turning
1 person
found this instruction helpful.
-
William from Canandaigua, NY
- Easy
- 15 - 30 mins
-
Socket set
I took a socket and removed the agitator bolt and cover which exposed the cogs. I cold see the cogs were stripped. I changed them and everything works fine.
Was this helpful?
Thank you for voting!
Worn out Cogs
1 person
found this instruction helpful.
-
Leo from Yorba Linda, CA
- Easy
- 15 - 30 mins
-
Socket set
I unscrewed the top cap by hand and used a socket wrench to remove the main center unit.
the rest was very straight forward.
the rest was very straight forward.
Was this helpful?
Thank you for voting!
The top of the agitator no longer would engage, the little ears were stripped
1 person
found this instruction helpful.
-
Charles from Mechanicsville, MD
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
I pulled the top off ( the fabric softner dispenser) unscrewed the nut pulled up on the agitator replaced the ears put it back together. . It works just as good as a $75.00 an hour repairman could have done. And the wife wanted a new washer? Ha
Was this helpful?
Thank you for voting!
The washer quit agitating
1 person
found this instruction helpful.
-
Jeff from Michigan City, IN
- Really Easy
- 15 - 30 mins
-
Socket set
I noticed the agitator didn't "lock up" in one direction to properly agitate the load (which in turn "agitated" my girlfriend. I took the agitator apart to find the dog ears were worn. I ordered some new ones at a cost of about $12 delivered fed-ex and had the new dog ears installed in about 15 minutes saving me a bag of money from the re
... Read more
pair man.
Read less
Was this helpful?
Thank you for voting!
agitator weak, hardly turning
1 person
found this instruction helpful.
-
paul from mount Juliet, TN
- Really Easy
- 15 - 30 mins
-
Socket set
took the cover off the top of agitator, removed 3/8" bolt that went through cam and secured agitator. removed agitator and replaced the 4 agitator dogs and cam.
replaced agitator, tightened bolt, replaced cover. the washer works like new again? thankyou for your help and the correct parts.
replaced agitator, tightened bolt, replaced cover. the washer works like new again? thankyou for your help and the correct parts.
Was this helpful?
Thank you for voting!
The little dogs in the top agitator were worn out.
1 person
found this instruction helpful.
-
Debra from Salem, WV
- Easy
- 15 - 30 mins
-
Socket set
Easy. I took the fabric dispenser off, popped the cap off the top of the agitator and my husband removed the big screw down in the hole. We pulled the thing apart, took the old part out, put the new part it, put it back together. The hardest part was getting the big screw loose. (That's where my husband came in.) My $75 washer I bou
... Read more
ght at auction works like a new one!!
Read less
Was this helpful?
Thank you for voting!
Dogs worn on agitator
1 person
found this instruction helpful.
-
Kenneth from Muncie, IN
- Really Easy
- 15 - 30 mins
-
Socket set
Removed top of agitator, then removed the nut holding the agitator in place, pulled up the second piece of the agitator, replaced dogs and put the agitator back together
Was this helpful?
Thank you for voting!
worn our Agit-dogs, agitator wouldn't pull clothes down
2 of 4 people
found this instruction helpful.
-
Douglas from Wetumpka, AL
- Really Easy
- 15 - 30 mins
-
Socket set
FIRST I printed the directions from an online DIY stie, then removed a single bolt from the center of the agitator. I dismantled the agitator, replaced the dogs, and used to printed page to help me reassemble the agitator. I then replaced the bolt. It's VERY easy, but you need the pictures to be sure you've put everything back in the c
... Read more
orrect place.
Read less
Was this helpful?
Thank you for voting!
Agitator wasn't turning
1 person
found this instruction helpful.
-
Walter from Brandon, MS
- Really Easy
- 15 - 30 mins
-
Socket set
After reading on line how others did it, it was simple. I lifted out the softener dispenser. Under that there was a plastic cap. You just lift it out - theres no fasteners holding it. It just fits snugly in place by means of an o-ring. Under that there is one bolt holding the agitator to the spindle. Loosen that and remove the whole agit
... Read more
ator. The agitator then comes apart in the middle. Just pull the two halves apart. The only tool you will need is one socket with a long extention and a ratchet. Once apart you will see the 4 plastic cogs that spin the agitator. The teeth were worn off of mine. I simply replaced the four cogs that come as a set. None of the other parts were worn to the point of needing replacement. I now have a fully functioning washing machine that was repaired for less than thirteen dollars!
Read less
Was this helpful?
Thank you for voting!
Top Agitator not turning
1 person
found this instruction helpful.
-
John from Asbury, IA
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Removed top agitator cover. Removed bolt and pulled out the cam holding the dogs. Assembled new cam w/dogs put in place and installed bolt plus agitator cap and was ready to wash.. Very Simple
Was this helpful?
Thank you for voting!
Top of Agitator would not rotate
1 person
found this instruction helpful.
-
Depeturie from Madison, AL
- Really Easy
- 15 - 30 mins
-
Socket set
1. Lift the softener dispenser up and out
2. Lift up the plastic cap underneath
3. See bolt...use ratchet with extension to loosen and remove bolt
4. Remove whole agitator by simply lifting it up
5. Place agitator on floor and separate top from bottom agitator by simply pulling apart
6. See 4 plastic cogs that spi ... Read more n the agitator. Like mine they are probably completely worn/stripped.
7. Replace old 4-cog set with a new 4-cog set. They are small and inexpensive parts! I did this and our machine is working just great!
This also gave me a chance to clean the agitator thoroughly!
2. Lift up the plastic cap underneath
3. See bolt...use ratchet with extension to loosen and remove bolt
4. Remove whole agitator by simply lifting it up
5. Place agitator on floor and separate top from bottom agitator by simply pulling apart
6. See 4 plastic cogs that spi ... Read more n the agitator. Like mine they are probably completely worn/stripped.
7. Replace old 4-cog set with a new 4-cog set. They are small and inexpensive parts! I did this and our machine is working just great!
This also gave me a chance to clean the agitator thoroughly!
Read less
Was this helpful?
Thank you for voting!
Agitator would not agitate properly
1 person
found this instruction helpful.
-
Dawn from Little Rock, AR
- Easy
- 15 - 30 mins
-
Socket set
I also ordered a new agitator repair kit which had almost everything. I noticed that I the kit had shorted 3 of the 4 cogs. Once the missing parts were received I removed the agitator bolt from the middle of the agitiator with a rachet and socket. Amazingly, I read the instructions and followed them accordingly. I pulled removed the a
... Read more
gitator and removed the dogs/cogs and placed the new one in the new dogs *Making "dog gone" (pun intended) sure they were facing the correct way, by comparing them to the instructions. I carefully seated them as per the illustrations on the instructions and replaced the center bolt in. placed the cap on top and started the washer. Then I had my cup of coffee. By the way..I'm a grandmother, so if I can do it.............!
Read less
Was this helpful?
Thank you for voting!
the "dogs"did not work anymore sothe agitator wasn't turning
1 person
found this instruction helpful.
-
joaquin from camarillo, CA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
only took a nut out got parts out replace the "dogs" and that was it,put parts back in place and done.Something I want to point out is that it would be much better if part select use the post office better than fed ex is faster and cheaper.
Was this helpful?
Thank you for voting!
Top partion of agitator turned in both directions by hand and was not driven by the motor.
1 person
found this instruction helpful.
-
Charles from Lindenhurst, NY
- Easy
- 15 - 30 mins
-
Socket set
Using the IPB I removed the upper assembly to gain access to the cogs. Turned the assembly over and incerted the new parts and reassembled the pieces in reverse order.
Was this helpful?
Thank you for voting!
I happened to have the lid open when agitation began. I heard grinding, and the top of the agitator wasn't moving much.
1 person
found this instruction helpful.
-
Stephen from GROVER, NC
- Really Easy
- 30 - 60 mins
-
Socket set
I shut the machine off and came to the site . I got the impression that it could have been several things. I made the wash and rinse very brief to minimize further damage. My clothes didn't get clean. I just had to pop the hubcap and remove a 7/16 hex head screw to see there was no damage but broken dogs. I hadn't needed to abort the was
... Read more
h. I think they've been broken 15 years but didn't happen to make noise before. if the top piece of the agitator were called the circulator, I would have figured it out years ago. On full loads, clothes didn't circulate very well and tended to come out with deposits of lint. I think friction from a coating of soap scum kept the circulator moving enough to fool me, but it wasn't doing its job. I heated baking soda in water on the stove to make washing soda. I soaked the parts to remove soap scum, paying special attention to the ring of cogs that the dogs would engage. I replaced the thrust spacer because it was cracked. I didn't feel any grease or see any wear, so I think the only function for grease would be to prevent squeaks. Now, with a full load, clothes and water circulate better than I remember.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!