11020022013 Kenmore Washer - Instructions

Removed the top on the agitator. Then removed the screw with a wrench. then I removed the cam and replaced each Directional cog the way they came out. Then I replaced the cam. Tightened the screw on the agitator and replaced the top. Turned the machine on and It started agitating like it was suppose to.

The repair was very easy, I took the top cap off the agitator and removed the recess bolt and pulled the agitator out of the washing machine,put the agitator on the floor and put my feet on the sides of the agitator and pulled the top haft apart,replaced the agitator directional cogs put back together work great

Remove the adgitator cap, remove a 7/16 bolt inside the agitator, lift out the top half the agitator and replace the guts with the new one. then insert and replace the bolt and snap the cap back on. The whole process didnt take 5 minnutes. it took longer to drive to the peoples house than it did to do the repair ! damn shame i couldnt charge by the minnute instead of by the hour. I cant believe kenmore got away with putting such junk on the market ! I' m sure many of these kits are being sold to those who do heavy loads od laundry!

I popped the liquid detergent cap off of the top of the Agitator. I then removed the seal cap to expose the Agitator dog assembly and bolt. I removed the entire Agitator dog assembly and Agitator by removing the single 7/16? bolt. I pulled the old dogs out, put the new dogs in and reassembled the Agitator Assembly.

Works like new!!

Removed top portion of agitator to expose the nut which held it to the shaft and removed the nut with a socket and ratchet. Removed the entire agitator and carefully took apart the plastic part which held the old directional agitator cogs (4 of them) and removed them and replaced with the new ones which I had ordered. I then reassembled the agitator and dropped it in place and fastened & tightened the one nut which I had removed earlier. The entire process probably took about 10 minutes and we immediately tried the washing machine and observed that the top portion of the agitator was turning exactly as it was supposed to and I am extremely pleased that I was able to make the repairs myself. This was a very pleasant process and I would highly recommend your business to my friends and relatives. Thank you very much for your efficient help.

Sincerely,

Ken Lancaster

I removed the center cap from the agitator, which then exposed an inner cap with rubber seal. These were both easily removed with no tools... just a slight pull. Then the center screw was exposed. I removed that "one" screw and pulled the upper agitator assembly off. The old dog ears literally fell right out. I simply ensured that I placed the new dog ears in the same direction as the old, which is not hard to remember because the little housing piece that holds them is molded in the angle of the ears. Putting it back in took the most time because the new ears can easily fall out. In order to overcome this I had to assemble the pieces that had been removed and carefully put them back in place. At that point I had to manage to get the screw back into position and tighten it up. I put the inner cap with seal back in place and then the agitator cap... Done! It's an old machine but works great with a simple repair. The dog ears were so inexpensive that I purchased two sets. Great site!

Took the cap off the agitator, loosened the nut with a wrench, and pulled the agitator out. The agitator pulled apart easily, revealing the piece containing the dog ears, which were clearly worn out. Simply replaced the dog ears and reinstalled the agitator. Piece of cake!

Very easy repair. Popped off the top cap on the agitator with a flat head screwdriver. Then took a half inch drive socket set with the extender and removed the assembly where the cogs were housed. Inserted new cogs, put it all back together and the thing agitates like new. Simple. Saved huge dollars.

I just took the bolt out of the top of the agitator which allowed me to pull the agitator straight up. Then I turned it over so the sleeve that the cogs go into could fall out. I took the old cogs out, put the new cogs in, held it upside down and lowered the agitator down onto as to not move the cogs. When it was all situated correctly I held it by the bolt as I turned it upright. Then I just lowered it back down in place inside the drum and tightened the bolt back down. Done.
The washer works just like new.

First I removed the pop off cap at the top of the spiral shaped top agitator. Then reach down inside and pry off another pop off water tight cap exposing a 7/16 or 1/2 inch nut. A deep socket would probably be easiest but I didn't have one so a nut driver and luck got it unthreaded- it was pretty tight and yoiu have to hold the agitator from spinning while you unthread. Then the upper agitator asslembly lifts out and the cog assembly falls apart but it's only like 3 or four housing pieces and it only goes together one way to hold the four new cogs in place. reassemble and the machine works great again

With screwdriver removed the agitator top cap. Then with a 3/8 drive socket set removed the bolt holding the agitator assy. to the driveshaft. Removed the drive dog assy. Installed the agitator repair kit and put the complete agitator back together in reverse order. That was it! Works great

I took out the fabric softener dispenser, then pulled of the plastic plate. There is 1 big bolt that has to be unscrewed in there. After that gets unscrewed, the whole agitator will pull out of the washer. I put the agitator on the ground, stepped gently with both feet on th bottom (mostly flat part). then I pulled on the top cylinder part, and the 2 parts separated. There is a little disk in the cylinder part that pops out. remove the top and replace the cogs. then put the disk back together. Push the two big main parts of the agitator back together...snap the disk back in and put the whole agaitator back in your washer. pop it back into place and screw in the bolt.....DONE! I have to replace these cogs about 1ce a year...it costs me about $5 and 15 minutes...but it keeps my waher running great!

one bolt in middle of the agitator. everything pulls straight out. spacer is on top of the other agitator. the top agitator if you turn upside down the clogs are under it. there is a black spacer that holds the clogs in place. the clogs will only work one way. put black spacer back on. put top agitatar back on top of bottom agitator. screw bolt back on and your done. turn washer on and see if everything is working well.

disassembled two halves, cogs just sitting there, replaced, re-assembled

We took off softner cap and then took off the agitator with a nutdriver and then pulled the top off and the central agitator that the cogs were in pulled it out took the cogs out and replaced them with the new ones . Then we put the agitator back on and tightened the nut and replaced the softner cap and we were all done.