Ask our experts a question about this part and we'll get back to you as soon as possible!
18 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
George
March 28, 2018
Unit will run all cycles, drain completely, and heat to dry but later i can hear a pump run and it will refill the unit with water from the bottom even with the door open. Suggestions?
For model number SHE3AR56UC/07
Hi George,
Thank you for your question. I would suggest maybe taking a look at your water inlet valve, your float switch, and your door switch first. You can test those parts with a multi meter to be sure that they are working. If they are all fine, it might be your control board that is causing your machine to start filling up again even when the door is open. I hope that helps. Good luck with your repair.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Steve
May 28, 2019
The dishwasher runs for a few minutes and then stops and the "clean" light comes on. Internet sites i have looked at say it needs a new control unit.
For model number SHX3AR52UC/13
Hello Steve, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number PS8737027. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Jackie
June 18, 2019
Is this the correct control unit for my dw
For model number SHE3AR72UC/22
Hello Jackie, thank you for writing. This part is not shown as compatible to your model. For your model the replacement is part PS11732428.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Terry
July 10, 2019
Only the "refill rinse aid" light flashes. No main display at all. Worked fine up to today.
For model number SHE3AR72UC/21
Hello,
Sounds like your control panel may need to be replaced. The part you need is PS8735100.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Mark
December 18, 2017
The dishwasher is dead (nothing lights, etc.) there is no fuse or reset, etc. Not the door latch either. So before i buy one or the other... how do i know if the problem is the control board in the door, or the control board in the base.
For model number SHE3AR75UC
Hello Mark, Thank you for your inquiry. You can test both control units with a multimeter. If you are unfamiliar with how a multimeter functions, there are YouTube videos available to assist you.Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Jerry
January 2, 2018
It starts but does not have water going to it cause it shuts off rite away and shows that cycle is done
For model number SHE3AR52UC/08
Hi Jerry, Thank you for the question. If the appliance is not filling I suggest testing the Water Valve, PartSelect Number PS8728724 with a multi meter to check for proper resistance. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Joe
September 4, 2019
The dishwasher went completely out after a power surge and still does not come on (no lights or other signs of power). Which part or parts might need to be replaced?Thanks!
For model number SHE3ARF2UC/12
Hello Joe, Thank you for the question. Sounds like the surge may have burnt out the Control Unit, PartSelect Number PS8736196 and it will need to be replaced. Hope this helps!
My dishwasher will not complete the full cycle, it will run about an hour and then i get the e25 error. I have replaced the drain pump and cleared out the drain lines, then it will run again about an hour (or less) through the cycle. I do observe it successfully draining but it eventually stops. Can you advise if this model has a drain solenoid or a timer or do i need to replace the whole controller?
For model number SHE3AR75UC/08
Hello and thank you for writing.
Error e25 indicates drain pump problems or the drain pipe blockage. As you already checked for blockage this would point in the direction of a malfunctioning drain pump PS8727352, as you also have replaced this part it certainly sounds like it could be a faulty switch PS8727333 and/or malfunctioning control unit PS8736195 you should check the part(s) for signs of damage or test with a multimeter, and replace the part(s) as needed, there is no solenoid and the timer is connected to the switch and board and would be only rarely the cause for this. We hope this helps. Please contact us anytime if you require further assistance.
Bosch dishwasher seems loud but runs more of less ok... consistently get E:02 error near end of cycle.. any suggestions?
For model number she3ar75uc/22
Hi Steve, thank you for contacting us. Based on our research, a low buzzing sound from your dishwasher can be normal as the dishwasher grinds or buzzes when it forces water down the drain. However, the e02 error happens because the dishwasher is not able to heat the water due to a faulty control module or heating element. This usually means that there is a connection or wiring problem with components like the control module or the heating element. You may need to check the control unit, part number PS11732428, to fix the error code. Good luck with your repair!
Hello,
The dishwasher won't fill. A new Bosch inlet valve was installed, but no water flows. I verified 115 vac at the connector (when disconnected) and 0.1 v when connected (indicates current is flowing through the coil). Coil resistance is 965 ohms. I made a patch cord to connect the coil to a wall outlet. When plugged in, the valve opens, water flows, and the dishwasher operates normally. It appears the controller isn't capable of supplying enough current to actuate the valve. Short of replacing the controller, is there something else i should check / replace? A new float switch was also installed after i broke one of the connector retaining tabs while checking its continuity.Thank you!
nathan
For model number Bosch SHE3AR55UC/07
Hi Nathan,
Thank you for your question. If you have checked the water inlet valve and the dishwasher is still not filling with water, there are some other parts that you will need to check to see which one is causing the issue. You will also need to check the float, the float switch and the door switch. We hope this helps. Thank you and have a great day.
Was this helpful?
Thank you for voting!
< Prev
1
2
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
