Part Location Diagram of WH01X10302 GE 6-Rib Drive Belt
See part 603 in the diagram
Replacing your General Electric Washer 6-Rib Drive Belt
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

customerservice@partselect.ca

6-Rib Drive Belt

 Fits your HSWP1000M4WW!
★★★★★
★★★★★
2 Reviews
$45.99
  Special Order
 Fits your HSWP1000M4WW!
PartSelect Number PS1482278
Manufacturer Part Number WH01X10302
Manufactured by GE
Product Description

6-Rib Drive Belt Specifications

This drive belt is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Part Videos

Replacing your General Electric Washer 6-Rib Drive Belt

Replacing your General Electric Washer 6-Rib Drive Belt
Troubleshooting
This part fixes the following symptoms:
Will not agitate | Spins slowly | Will not drain | Burning smell
This part works with the following products:
Washer.
This part works with the following products:
General Electric, Hotpoint.
Part# WH01X10302 replaces these:
AP3968432, 1264395, WH01X10353
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
2 Reviews
3.5
Filter By Rating:
  • 5 Stars
    1
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    1
  • 1 Star
    0
  • 1
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
Customer Repair Stories
 Average Repair Rating: 2.9 / 5.0, 25 reviews. What's this?
  • 1
  • 2
  • 3
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
broken drive belt
To diagnose, first I unhooked the washer: power, water supply, and drain pipe. I then slid the washer out, laying it on its front. With nutdriver, I unscrewed two screws that held the other end of the drain tube and removed it completely. Then, again with the nutdriver removed 4 screws from the back near the legs, two in between the legs in the middle, and approx. 4 to 6 on the bottom. This let me pull the bottom off partially to access the motor area. (I did did not take the bottom completely off, only about 2/3 off and let it bend over, as it was flexible tin) The belt was broken. After receiving the new belt, I positioned it between the pulley and the motor and between the drum and the big pulley. Then I rotated the big pulley, pulling the belt onto it as I rotated. At the same time, as I rotated, I pulled the other end of the belt on to the little pulley. Once it was on, I would put pressure on it as I turned the pulley, to jump the belt to the appropriate grooves on the little pulley. Note: the replacement belt had been modified, so it had one less groove than the pulley. I would have known this if I had read the insert that came with the belt first! Anyway, this was not a problem, only a design change. Also it was important to start the belt on the inside, so if it slipped, you didnt loose your bite. Total diagnostic, repair, and reassembly time: 30 minutes plus or minus. I had read other online forums that said you had to loosen the motor, etc. And I do know some type of a belt installation tool was offered on line, but I got along fine with my installation method. An extra set of hands would have been helpful, but not necessary.
Other Parts Used:
  • jon from barry, IL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
92 of 111 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken belt.
Used 1" puddy knife to depress spring loaded retainer tabs. Front panel is removed by prying the top of the front panel away from the machine. Lift front panel to release bottom from machine. Set panel aside. New belt is installed by placing it on the drive pulley and then rolling belt onto the motor pulley. Rotate the motor by hand while moving belt so it is properly seated on pulley.
Other Parts Used:
  • Mike from Meridian, ID
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
33 of 37 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer drum would not spin, broken belt
I used a butter knife to pop plastic clips that hold the front panel to the top panel, one clip on each side of front cover. I never thought the new belt was going to fit, it barely fit on the big pulley, much less around the small pulley too. It needs to be stretched a lot to get it on.. but it will fit :)
Other Parts Used:
  • Eric from Bel air, MD
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
20 of 22 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
belt fits too tightly toget on easily
took two people to get this belt on
Other Parts Used:
  • Travis from Hagaman, NY
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers, Wrench (Adjustable)
18 of 24 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Would not agitate or spin dry
After confirming what I thought was the problem and reading other posts it was fairly easy to replace the belt. After taking the bottom cover loose to gain access to the large and small pulley I found out that the belt was very tight to get on as a previous customer had mentioned. I also used visegrips to hold the belt in place on the large pulley while guideing the belt on the small motor pulley with one hand and turning the drum pulley with the other hand. It helped that I had read the other post first. Next time will be a snap.
Other Parts Used:
  • Ron from Mount Vernon, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
15 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Drive Belt
Removed bottom washer plate. Placed belt on small, grooved pulley. Started belt on larger pulley. Clamped lock pliers to larger pulley to prevent belt from slipping off. Turned belt onto larger pulley by turning and pressing the belt close to the smaller pulley. Adjusted belt and replaced bottom plate.
Other Parts Used:
  • Dirk from Anamosa, IA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers
15 of 18 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Very Noisy In Spin
When disassembling I could not remove the 1 3/4" tub nut with in house tools and had to order the spanner wrench. Almost mandatory unless you have a socket wrench.
Other Parts Used:
Tub Bearing Tub Bearing Washer Tub Dampening Strap
  • Robert from HOLLAND, MI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
14 of 19 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Clutch drive wore out and was making a clunking noise during operation.
I removed the front cover and the top cover. Then I unplugged all the,wires and removed the hangers. Then removed tub and drum together out the front. After beating on the tub nut for 2 hours and drenching it in liquid wrench I realized that the,tub nut was not going to release. Yes I was turning it clockwise. I bring out my chisel and hammer. After removing the,center shaft I chisel the,tube inward till I could get to the nut. Then I chisel the,tub nut into 3 pieces. It then appeared why it wasn't coming loose,earlier the powders,had gotten below the nut and had it cemenred on. So those youtube videos,are helpful to an extent.
Other Parts Used:
Tub Seal DRIVE PULLEY Hub Nut
  • howard from LA FAYETTE, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set, Wrench (Adjustable)
9 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Very loud noise during the spin cycle
The first attempt to fix the problem did not turn out so well. I replaced the tub bearing, split ring, tub bearing washer and the hub washer. After reassembly and testing, the loud airplane noise was still present during the spin cycle
Then I ordered and replaced the mode shifter shaft assembly and, since I was going to disassemble again, also ordered a new 6-rib belt. Once reassembled and tested, it was quieter than when it was when brand new, according to my wife.
Parts came in very quickly and the tutorials/youtubes were spot on.
Other Parts Used:
Shaft and Mode Shifter Assembly
  • Walter from IRVING, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
7 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Very large noise during spin cycle
Tub seal was found completely broken. Replaced it.
Then replaced tub bearing, tub bearing washer, shaft & mode shifter assembly and 6-rib drive belt.
Reassembled and tried, more quieter and like new machine.

Loosening tub nut was a challenge as it was bit corroded, use of WD40 was a great help.
Knowledge from you tube was a great help.
Other Parts Used:
Tub Seal Shaft and Mode Shifter Assembly Tub Bearing Tub Bearing Washer
  • Ashok from CUPERTINO, CA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Socket set
6 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
  • 2
  • 3
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

13 questions answered by our experts.
  • 1
  • 2
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Gilbert
September 24, 2017
Hello, we just purchased a 6- rib drive belt, a drain pump assembly, and agitator coupling to rectify my washer spin problem. I installed all these parts but regrettable these parts did not fix the spinning problem i am back to square one. It spins slowly and never picks up momentum to spin dry the clothes. Therefore, the spin cycle leaves the clothes wet to where they need to be wrung out due to the amount of water that is still left in the clothes. What do you recommend i do to fix the problem. I'am at the end of my rope. Any advice would be greatly appreciated.
For model number WCRE6270G0CC
PartSelect logo
Hi Gilbert, Thank you for your question. I would suggest testing your door switch. If your door switch is malfunctioning, it will not allow your machine to go into the spin cycle because that would be a safety hazard as the machine thinks that the door is open. I would also suggest testing your drain pump as well. If both of those parts are fine, you may have to look into checking your motor. Good luck with your repair.

6 people found this helpful.

Was this helpful?
Thank you for voting!
Norma
March 14, 2018
Hello, we purchased the belt, replaced it and it worked. However, within the last few days, the washer will do 2-3 loads no problem, then it doesn't work again, all day. Then in the evening bam! It spins again. Please advise. Thank you.
For model number GLWN2800D1WS
PartSelect logo
Hello Norma, thank you for your question. I would recommend checking the lid switch assembly first. If the switch is functioning intermittently, the unit might work for a few loads then stop, then work again. That is the part Lid Switch with Wire Harness PartSelect Number: PS1482372. If that part is tested and is functioning properly, you will want to check the Shaft & Drive Tube Assembly Part Number: PS3652839 as well as the Drive Motor and Inverter Assembly PartSelect Number: PS8746234. I hope this helps!

4 people found this helpful.

Was this helpful?
Thank you for voting!
Keith
May 28, 2019
How can you tell if the motor has gone out on the washer? It won't spend or agitate. And the belt is good.
For model number Wlsr3000g1ww
PartSelect logo
Hello Keith, Thank you for the question. With a defective motor you can at times smell a burning or hear a hum noise coming from the motor. You can also test it with a multi meter to check continuity. Hope this helps!

4 people found this helpful.

Was this helpful?
Thank you for voting!
Jerry
September 22, 2017
It spins but when it come to the 4 minute faster speed it slows down for that last cycle instead of speeding up. I sprayed some belt dressing on the belt but it didn't help. I tried the 6 minute drain and spin and when it got to the 4 minute it slowed down just the same.
For model number wpre6150k2wt
PartSelect logo
Hi Jerry, Thank you for your inquiry. If you are having an issue with the washer not spinning correctly there are a few parts you will need to check. You will need to check the drain pump, the tub dampening strap, the split ring,the hub washer, the tub seal, the tub bearing, the shaft and mode shifter assembly and the tub bearing. I hope this helps. Thank you and have a great day!

3 people found this helpful.

Was this helpful?
Thank you for voting!
Brad
May 3, 2019
Washer won’t agitate or spin. Sometimes it will try to agitate but it barely moves. It did spin for me once yesterday, but stopped again altogether. It fills and drains just fine. What part should i get?
For model number WJRE5500G1WW
PartSelect logo
Hello Brad, Thank you for the question. I suggest checking the Belt, PartSelect Number PS1482278 to see if it is wore out and slipping or is lose. You can also check the Agitator Coupling, PartSelect Number PS1482517 for damage or wear. Hope this helps, good luck with this repair!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Handy
March 8, 2024
everything works fine, but noticing very slight petro? type smell best we can tell during spin cycle. it does go away. clothes smell fine. opened cabinet no leaks. it is not a burnt smell any thoughts??
For model number WLRR5000G0WW
PartSelect logo
Hi Handy, thank you for contacting us. Washing machines have various moving parts that require lubrication to function smoothly. If there is a slight smell of petroleum, it is possible that some lubricant has leaked onto a hot surface, such as the motor or a spinning component, causing it to emit an odor. Check for any signs of oil or lubricant leakage around the shaft and mode shifter assembly, part number PS2354082. We hope this is helpful!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Ian
March 20, 2024
Not spinning all the water out. I have removed all the hoses from the pump to check for clogs but have not found anything. Any suggestions? Thanks
For model number GTAN2800D1WW
PartSelect logo
Hi Ian, thank you for getting in touch. Based on the description that you have provided, we would recommend replacing the drain pump, part number PS3654194, to fix the issue. It removes water from the washer during the drain portion of the cycle. Glad to be of help!

Was this helpful?
Thank you for voting!
Related Parts:
Pam
November 23, 2019
I don't have model # only serial #...175d2750g335. is this the correct belt?
PartSelect logo
Hi Pam, sadly we do need the model number, the serial number does not allows us to find compatibility. Thank you for your question and good luck with your repair!

Was this helpful?
Thank you for voting!
Steven
September 18, 2021
Belt replacement tool
For model number GTWn4250d0ws
PartSelect logo
Hi Steven, Thank you for your question. The part number listed under your model number for the belt installation tool is PS10065458. If you would like to place an order for it, you may order it either online or by calling our customer service line and anyone will be happy to assist you. We hope this helps! If you have any questions, please let us know.

Was this helpful?
Thank you for voting!
Mary
February 2, 2022
I am needing a belt for a 4 year old hot point washer. Model # HSNP1000M4WW
For model number HSWP1000M4WW
PartSelect logo
Hello Mary, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is PartSelect Number PS1482278. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!

Was this helpful?
Thank you for voting!
  • 1
  • 2
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS1482278
Manufacturer Part Number: WH01X10302
Brand
Model Number
Description
General Electric
57431DCWW
General Electric
57441DCWW
Washer
General Electric
57481DCWW
Washer
General Electric
57751H0WW
Washer
General Electric
57751H1WW
General Electric
57751H2WW
General Electric
57751H3WW
Washer
General Electric
58971K0WW
General Electric
58971K2WW
Washer
General Electric
58971K3WW
Washer
General Electric
EJRR4170E6WW
General Electric
EWA4500DCWW
General Electric
EWA5600G0WW
Washer
General Electric
EWA5600G1WW
Washer
General Electric
EWA5600G2WW
Washer
General Electric
EWA5600G3WW
Washer
General Electric
EWA5600K0WW
Washer
General Electric
EWA5600K1WW
Washer
General Electric
EWA5600K2WW
Washer
General Electric
EWA5600K3WW
Washer
General Electric
EWA6500DCWW
General Electric
GBAN2800F0WW
Washer - WASHER
General Electric
GBSR3140H1WW
Washer
General Electric
GBSR3140H2WW
Washer
General Electric
GBSR3140H3WW
Washer
General Electric
GBSR3140H4WW
Washer
General Electric
GBSR3140H5WW
Washer
General Electric
GBSR3140H6WW
Washer
General Electric
GBSR3140H7WW
Washer
General Electric
GBSR3140H8WW
Washer
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

Contact Customer Service