My Orders
57481DCWW General Electric Washer - Overview
Diagrams for 57481DCWW
See every part. Know exactly what you need.
Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".
Search filter:
Clear Filter
Your search term must have 3 or more characters.
No Longer Available
DAMPENING STRAP 2PACK
Part #WH01X39337
The tub dampening straps support the wash tub and reduce vibration by keeping the tub at the center of the cabinet. If your washer shakes and moves, or is making a loud banging noise during the wash cycle, the washing machine tub could be off-balance, meaning one or more of these straps may be loose, or broken. Other symptoms include: the...Read more washer leaking, not agitating, or pumping but not spinning. These straps are sold individually. However, we recommend that you replace all 4 straps at the same time. It is also recommended that you check the tub for cracks where these straps mount.
Read less
No Longer Available
$27.58
Special Order
Tub Seal
Part #WH02X10383
The main tub seal is located between the transmission and the outer tub. It's the primary water seal in the outer tub for the transmission-shaft. This seal is difficult to replace and should probably be installed by a qualified technician.
$142.92
Special Order
Dual Action Agitator
Part #WH43X10034
This does not come with the fabric dispenser - must order separately or use original part.
$47.16
Special Order
Tub Bearing
Part #WH2X1198
This tub bearing goes in your washing machine. You will find it on the bottom of the outer tub, where the transmission goes through the tub. If you hear metal on metal when the washer is spinning, you may need to replace the tub bearing. This bearing is made of metal, and is approximately 3 inches wide and 2 inches tall.
$13.95
Special Order
Tub Bearing Washer
Part #WH2X1197
$29.12
Special Order
Hub Nut
Part #WH2X1193
This part is the hub nut, or lock down nut for your washing machine. It is designed to hold the inner tub on to the transmission. If your hub nut is stripped or damaged, it may need to be replaced. This hub nut is approximately 1.5 inches in diameter. This is an OEM part sourced directly from the manufacturer. You will need a hub nut wrench and some WD40 to loosen the nut and remove it from the agitator shaft.
No Longer Available
$79.66
Special Order
Drain Hose
Part #WH41X10096
This drain hose is a replacement part for your top-loading washer. The hose measures 57 inches in length.
$137.13
Special Order
Drain Pump and Motor Assembly
Part #WH23X10030
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.
$49.38
Special Order
6-Rib Drive Belt
Part #WH01X10302
This drive belt is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear.
$92.82
Special Order
Agitator Coupling
Part #WH43X10032
Bolt not included. This part connects the transmission drive shaft to the agitator base.
Common Symptoms of the 57481DCWW
How this model fails, and the parts that fix it.
Leaking
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Will not agitate
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
No hot or cold water
Fixed by
these parts
these parts
Show All
Marks left on clothes
Fixed by
these parts
these parts
Show All
Shaking and Moving
Fixed by
these parts
these parts
Show All
Spinning Issues
Fixed by
these parts
these parts
Show All
Spins slowly
Fixed by
these parts
these parts
Show All
Does not dispense fabric softener or detergent
Fixed by
these parts
these parts
Show All
Burning smell
Fixed by
these parts
these parts
Show All
Noisy and Marks Left on Clothes
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Touchpad does not respond
Fixed by
these parts
these parts
Show All
Water Filling Issues
Fixed by
these parts
these parts
Show All
Draining Issues
Fixed by
these parts
these parts
Show All
Watch our pros, then fix it yourself.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!
View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washing Machine was not draining water from tub.
304 of 334 people
found this instruction helpful.
1. Drained the wash tub by taking the drain hose from the back of the washing machine and dropping it below the tub - water flowed out of hose a lot easier than trying to suck water out of tub using a pump (tried this on the first time I tried to fix washer). (Washing machine on 2nd floor of house and didn't want water running on floor)<
... Read more
br />2. Removed the 2 bolts holding the Pump/Motor assembly to the machine.
3. Removed both hose clamps on the Pump/Motor assembly and removed Pump.
4. Attached the new drain inlet hose to the pump and then to the tub with the original hose clamps.
5. Attached the drain hose to the pump and then plugged in the 2 wires for the pump.
6. Plugged in the washing machine and everything worked.
NOTES:
1. Hardest part was working with hose clamps (spring type clamps) in the tight space under the machine.
2. Easier to fix since I pulled machine apart a few days before - removing the clog in the pump/motor assembly only to get everything back together to find out that the motor was dead. Still well worth the time and effort due to not having to go out and buy a new Machine...
3. Removed both hose clamps on the Pump/Motor assembly and removed Pump.
4. Attached the new drain inlet hose to the pump and then to the tub with the original hose clamps.
5. Attached the drain hose to the pump and then plugged in the 2 wires for the pump.
6. Plugged in the washing machine and everything worked.
NOTES:
1. Hardest part was working with hose clamps (spring type clamps) in the tight space under the machine.
2. Easier to fix since I pulled machine apart a few days before - removing the clog in the pump/motor assembly only to get everything back together to find out that the motor was dead. Still well worth the time and effort due to not having to go out and buy a new Machine...
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Old Hose Had A Leak
129 of 146 people
found this instruction helpful.
First I removed the screws that held the hose drain hose clip in place. Removed the damaged hose. Placed the new drain hose clip at the end of the new drain hose. Re-inserted back in hole, pushed in hose to necessary depth then tighted screws, Very easy and painless.
Other Parts Used:
Was this helpful?
Thank you for voting!
The Hub Under the Spinner basket broken/ Deteriorated
114 of 135 people
found this instruction helpful.
Removed front cover, Control panel, top Cover, slasher unit, all very smiple stuff. the hub was broken and the spinner basket came right out. One half Hub attached to Spinner, Other half attached to Hub drive shaft. removing the Hub nut was the hard part. tried impack & socket, No luck. in removal. Had to usr Hammer & Chise
... Read more
l and bust Old Alum. Nut off. Clean up and replace parts. OK. Had to remove water pump and clear debree that went in pump when spinner Hub broke off . the spinner also bursted a crack in the outer poly tube when it cam apart.. Sanded the dmage area and Patched with a good coat of JB Weld. machine is working Like new. The parts all worked Great. the break down Chart was a great Help to get the right parts needed. Thanks
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!