- Home
- SCA1001KSS02
- Instructions
SCA1001KSS02 General Electric Microwave - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Door latch assembly
1 of 2 people
found this instruction helpful.
-
Garry from HILTON HEAD, SC
- Easy
- 30 - 60 mins
-
Screw drivers
Read other folks on your site on how they did it and I followed their directions. About 30 minutes and it was done. Figured I saved lots of money. Thanks
Was this helpful?
Thank you for voting!
bulb and reflector assembly replacement
1 of 2 people
found this instruction helpful.
-
Joseph M from Northville, MI
- Easy
- 30 - 60 mins
-
Screw drivers
When trying to replace the light bulb for the underneath night light, I damaged the female receptor plug by not inserting it gently and straight on, and thus couldn't insert the bulb. So, I had to replace the receptor which is part of a the reflector assembly with the small attached plug cord. Once I was able to unscrew the glass cover
... Read more
and move the existing reflector panel aside to see how it fit together, it went well and is now working fine. One hint in replacing bulbs is to order the correct one, since there is another bulb for the interior light for the microwave which uses a different bulb. Be sure to order the correct one. Also, push them in gently but firmly right on center.
Read less
Was this helpful?
Thank you for voting!
installed new kitchen cabinets
1 of 2 people
found this instruction helpful.
-
andrew from HOMOSASSA, FL
- Easy
- 15 - 30 mins
the problem was the mounting bracket that was installed when the house was built ,was not the bracket that came with the microwave. It was used to step the microwave out 3" in front of the other cabinets for the style that they were using then. so when I was installing the new cabinets I didn't want that style, so I ordered the original m
... Read more
ounting bracket. It was a perfect fit and the install went great
Read less
Was this helpful?
Thank you for voting!
Glass turntable broke when being washed.
1 of 2 people
found this instruction helpful.
-
Lee from Spartanburg, SC
- Really Easy
- Less than 15 mins
Ordered the part on Monday, it was delivered on Wednesday, only paid for standard shipping. All I had to do was put it in, right part, back to new!
Was this helpful?
Thank you for voting!
Thermostat quit.
1 of 2 people
found this instruction helpful.
-
Tony from ITHACA, MI
- Easy
- Less than 15 mins
-
Screw drivers
Checked all sensors with a multi-meter, found the thermostat to be the problem, no continuity.
Was this helpful?
Thank you for voting!
cover fell apart
0 of 1 people
found this instruction helpful.
-
Esther from Brooklyn, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
removed screw from inside wall. removed leftover board & replaced with new board & screw. good as new!!!
Was this helpful?
Thank you for voting!
Replacement of Magnetron
0 of 1 people
found this instruction helpful.
-
Benjamin from Anchorage, AK
- Really Easy
- 15 - 30 mins
-
Screw drivers
I UNPLUGGED the microwave and removed the cover, using a phillips and a Torx screwdriver for the machine screws. I set these screws aside, so as not to confuse them with the later encountered screws. I photographed the magnetron to assure proper placement of the 6 phillips machine screws involved in reassembly (marking the the locations
... Read more
on the old magnetron would do as well. I marked the old magnetron "old", to avoid later confusion. I removed the two screws holding the shields to the magnetron. I removed 3 of the 4 screws holding the magnetron to the microwave, leaving one of the top screws. I held the magnetron securely and removed the last screw, pulling out a the part of the magnetron that penetrated the microwave. I installed the new magnetron in reverse order. One problem I encountered was locating one of the six screws, which had been pulled into the old magnetron by magnetism.
Read less
Was this helpful?
Thank you for voting!
No heat
0 of 1 people
found this instruction helpful.
-
Edwin from New York, NY
- Really Easy
- 15 - 30 mins
-
Screw drivers
Replace the fuses
Was this helpful?
Thank you for voting!
No heat.
0 of 1 people
found this instruction helpful.
-
Mack from Jacksonville, FL
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Replaced the fuse. Result; did not fix the problem.
Was this helpful?
Thank you for voting!
no heat
0 of 1 people
found this instruction helpful.
-
Nelia from Streamwood, IL
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
unplug the unit then pull down , lot of screws are on top. open the cover . you could see the parts that need to replace on the right hand side (heavy side). disconnect wires then test the parts that need to replace by a tester to make sure that it's really broke .then unscrew part and replace .
Was this helpful?
Thank you for voting!
install new latch and spring in door
3 of 10 people
found this instruction helpful.
-
Clifford from Springfield, VA
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers
removed key pad then removed latch assembly and replaced it with new latch assembly.
Other Parts Used:
Was this helpful?
Thank you for voting!
Problem door latch
-
Ron from Southampton, PA
- Easy
- 15 - 30 mins
-
Screw drivers
Snap the plastic trim piece from the inside of the door off.took broken latch out and put the new one in.PS your part came really fast.Thanks
Was this helpful?
Thank you for voting!
Bottom door latch was broken. Microwave was dead.
-
James from Severn, MD
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
Read instructions and viewed video. Project would have been very difficult without the instructions and video. Step 1 removed vent grill at top to microwave, by removing two scres. Step 2 removed microwave door by lifting. Step 3 used a one inch plaster knife to separate the plastic interior cover of the door. The video was most help
... Read more
ful. Use the thin blade of the plaster knife to locate snap locations of the plastic cover. Step 4 removed broken latch by applying slight pressure to the outside. Observed the attachment of the 'spring'. Step 5 installed new latch and spring. Step 6 reinstalled interior plastic cover. Step 7 install door. Step 8 install vent cover with two screws. Step 9 test unit.
Read less
Was this helpful?
Thank you for voting!
microwave just stopped working
-
James from Fall Branch, TN
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
First unplugged the microwave, took top grill off, took control panel off, took wires off and used color coded tape to make sure they went back in right places, took fuse out and replaced it and put every thing back and it all worked fine and to top it off my wife did it all. So it was pretty easy.
Was this helpful?
Thank you for voting!
Could not be turned on
-
Remer from Dothan, AL
- Really Easy
- 1- 2 hours
-
Screw drivers
Removed outer cover and then replaced the T. C. O. located on the left upper side if the unit. Replaced outer cover, tested oven. Oven operates normally.
Was this helpful?
Thank you for voting!