SCA1001KSS02 General Electric Microwave - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Timer operated normally, but the microwave did not heat water or cook food.
Our GE Profile Advantium 120 Series Over-the-Range Microwave stopped working. We called GE Service. The first available appointment was two weeks after our call. The technician charged $99, gave us a form stating that the Magnetron and Diode Cable as defective and quoting an additional price of $362 to furnish and install these parts. He said that it would be another two weeks before he could do the work. Instead I ordered the parts from you and had them within two days. The parts you furnished were identical to the original parts in our unit. They arrived within two days. I installed the parts without removing the microwave from the wall. The most difficult part was inserting the magnetron mounting screws into openings in the rather tight space available. I was able to do this by using plastic pacaging tape to hold the screws onto the end of a short Phillip screw, Prior to iserting each screw I pushed it through the sticky side of a piece of packaging tape. I then folded the sticky surface over the shank of the screw. Once a screw was seated, but before it was fully tightened, I used needle nose pliers to pull off the tape. The unit now functions perfectly.
Parts Used:
-
Peter from Severna Park, MD
-
Difficulty Level:Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
When trying to run, intermittently, the light would come on but the tray wouldn't rotate or cook. When the door was open, the tray would intermittently rotate.
I pulled out the unit and found 2 interlock switches that are depressed when the door closes. After cycling the door open/closed I found that one of the switches occasionally would stay depressed. The repair was easy (after I took off the panels so I could get to the switch) I simply removed 2 screws that attached the interlock switch assemblies to the main unit. Then I popped out the defective switch and popped in the new one. This did indeed fix my problem.
Parts Used:
-
Sam from Chandler, AZ
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Glass rotating tray cracked and broke when cooking
This is the tray the glass cooking tray rest on and rotates the glass during cooking. The metal tray was installed upside down. The rotating glass tray was not properly installed. The oven was at a very high temp. and the weight of the utensil on the glass was not supported correctly. Result, big " pop " and broken glass tray. Note this is the second glass repaced. The first one dropped while removing it from the oven. It stuck to the bottom of the cooking dish and then fell to the floor. Pop, big breakage. Maybe you can learn from my mistakes.
Parts Used:
-
paul g. from westlake village, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Broken Glass Cooking Tray: need replacement part
Took item from sealed box and removed protective bubble wrap. Placed tray in microwave, aligning tray with turntable sprockets. Perfect fit, perfect match! And the part arrived in three days and was very competitively priced. What more is there to stay? Will use PartSelect for other replacement parts. No brainer!
Parts Used:
-
Steven D from Seminole, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
I broke the glass tray
I'm writing because I have never in my life had such an easy time finding a part, ordering it, and receiving it! Your service is truly unbelievable. I still don't believe it and I experienced it. Nothing went wrong and it could not have been easier. Please don't go away.
Parts Used:
-
Kimberly from San Tan Valley, AZ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Broken microwave glass tray
-
Frank from Arlington, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Change a burnt out bulb
Opened the lid over the bulb by removing one screw. Removed old bulb; a bayonet type with delicate prongs. Inserted new bulb. Best to turn off circuit breaker toi the micro for safety reasons.
Parts Used:
-
George from Fort Myers, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Replaced door to micro wave/convection
Removed vent above door. Opened old door all the way and lifted up. Door came off. Reversed proceed and I was done.
Parts Used:
-
Bruce from Winthrop, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!
Problem door latch
Snap the plastic trim piece from the inside of the door off.took broken latch out and put the new one in.PS your part came really fast.Thanks
Parts Used:
-
Ron from Southampton, PA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Just recently fixed and my son broke it a week later...
My son said order it. It came a day later. Very cool. He took the door off and up to his room. No idea what tools except most likely a screwdriver. I asked him how did it go. He said it's good. Nice...
Parts Used:
-
Amy from Hillburn, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
bulb burned out
opened the access door. It took some tugging to get the old bulb out, and is was awkward getting the prongs on the replacement bulb lined up and pushed in, but it was accomplished in about 10 minutes. You had exactly the right information on a change in the part number that was made by GE, and you shipped the correct bulb the same day I ordered it.Good job. N R Brown
Parts Used:
-
n from victor, NY
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
microwave won't heat
bought a fuse but that didn't solve the problem. Guess I need a new microwave
Parts Used:
-
Stephanie from Kernersville, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
broken door latch
I held the door open while the repair man took the black facing off and replaced the latch and reinstalled the facing I was worn out
Parts Used:
-
Mark from Meridian, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
replace plate
-
ed from virginia beach, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Had preheated the convection/microwave oven to bake 2 frenchbread pizzas for 25 minutes. Placed aluminum tray on top of glass plate with pizzas. 20 minutes into baking the plate cracked in half. Why? Don't know. Never had before.
Unpacked glass plate from cardboard box and placed atop rotating spindle inside oven - done.
Parts Used:
-
Pines, from Middletown, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!