This ceramic microwave fuse is just over an inch in length. It is white in the center, and metal on both ends. This is a 20-amp fuse, and is used to power your microwave. If the touch pad on the micro...
This is the replacement monitor switch for your microwave. It is black in color and measures approximately 1 inch by ¾ of an inch. This switch monitors the door latch position of your microwave and co...
There are two different couplers (also known as a turntable shaft) that can be used for this tray - a male D-shaped shaft and a female D-shaped shaft. The couplers are sold separately.
This filter is a genuine replacement filter for a microwave. It is metallic in color and measures about 7.7 inches wide and 5 inches tall. It features a finger tab for easy removal and installation. T...
Ask our experts a question about this model and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Sarah
January 16, 2020
Where can i find instructions on replacing the latch assembly for this microwave?
For model number SCA1001KSS02
Hello Sarah, Before you begin any repair please unplug the appliance from the electrical outlet. You will need to remove the plastic lining around the inside of the door. There are retainer clips holding the liner in place and you will need to use a putty knife to remove it. Depending on the type of microwave you have, you may have to come in from the bottom or from the top to remove the lining. Gently slide the putty knife in between the lining and the frame and go around the frame and gently pry it loose. On the hinge side you will need to come in from the backside to pry the lining off. The door latch is held in place by tension. There is a spring that is usually attached to the latch and to one of the fins on the door to provide it. With the inner lining removed you can now remove the old latch. Install the new latch by slipping it into the slots in the door and attach the spring to the bottom fin to allow for tension in the latch. Reinstall the lining and close the door. Plug the microwave back in. I hope this helps. Thank you and have a great day!
Do you have an online manuel. This is a GE profile, advantium, july, 2007
For model number SCA1001KSS02
Hello Joyce, Thank you for the question. Here is a link for the Owner manual. Hope this helps!
https://partselectcom.azureedge.net/assets/manuals/DB966DA17DC627931F3CCE439A2274F58ADCDC4E.pdf
Was this helpful?
Thank you for voting!
Gary
January 13, 2020
Microwave still operates but led display is out.
For model number SCA1001KSS02
Hello Gary and thank you for writing.
It certainly sounds like it could be a faulty control panel PS952666, you should check for signs of damage, and replace if necessary. We hope this helps. Please contact us anytime if you require further assistance.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Turned out the issue was easily solved by replacing a single, inexpensive fuse.
First off, UNPLUG THE MICROWAVE.
The fuse is located under the plastic grill at the top of the microwave. It's held on by two screws. Once you've removed the screws and taken off the plastic grill, you go to the right side of the microwave and remove another screw that holds a small metal grill in place. Removing the small metal grill is probably the toughest part of this repair. You kind of have to rock it back and forth a bit to get it to release. Once that's off, you can get to the fuse. I removed the burnt out one with a pair of needle nose pliers. I also put a small piece of cardboard under the fuse when I did this so I didn't accidentally drop it into the innards of the microwave. I did the same thing when I replaced the new fuse. I then plugged the appliance back in and made sure it worked. Once that was confirmed, I replaced both grills.
I have a GE Advantium/micorwave oven. It is the model that has the hinges on the side, NOT the bottom. First, removing the door is necessary. The grill has to be removed first, then the door lifts right out. Next the plastic backing on the door has to be very carfully taken off to expose where the new latch has to be placed. Use a flat screw driver or putty knife to go around the permiter releasing the internal, unseen, plastic catches that hold it on. This should be done carefully, to avoid breaking the catches that you can't see. After the plastic is mostly removed putting in the spring is not too difficult, but a second set of hands is almost manditory.
Easy as pie! 1. Remove the 2 outer screws holding the top vent in place and remove the vent (it helps to have the door open) 2. Lift the door up, pull the top of the door away from the hinge and then list it up a little more to clear the bottom hinge. 3. Lay the door on the counter and with a putty knife, work your way around the perimeter of the door between the door and the inside bezel. The bezel is held in place with little tabs spaced evenly around the perimeter. 4. Once the bezel is off, the catch assembly is accessible. List it up against the spring pressure, and push it towards the outside of the door to release it from the frame. 5. Reverse procedure to install.
