F31C747CS0 Frigidaire Dryer - Instructions

I contacted a company to come out and diagnose the problem. They informed me that the thermal limiter is bad and needed to be replaced for $15 for the part and $85 labor. I found the part on this site for about $10, and did the repair myself. The dryer was mostly dismantled so I pulled the drum back, and replaced the part. The tricky ... Read more part was the pulley system was, so make sure you see it before hand or find a diagram online. Once that was figured out, I set the drum back up, greased and tightened the pulley, reattached the front of the washer with connections, and closed the lid.

I don't think it would take others as long as it took me.
I had to take the drum out to get to the limiter. And my dryer is in a builtin housing with limited space in front of the dryer - so lots of manuevers to get access.

The limiter was very easy to find, thanks to diagrams on this site. The space between drum and li ... Read more miter made it impossible to get to the limiter screws without removing drum. Found very helpful drum removal instructions on PartSelect here:

http://www.partselect.com/PS1148434-Frigidaire-134503600-Dryer-Drum-Belt.htm?SourceCode=13&ModelNum=FSE748GFS0

Great site - thank you.

Removed 2 screws and replaced part--very easy.
I was very happy to find this part for a 1988 dryer

Unscrewed old frame, removed it and put in the new one. Now I have a brand new dryer. Thanks!

While changing power cable from 3 prong to 4 prong connection on a recently purchased used dryer I found the terminal block partially melted due to improper connectors which overheated. The bracket and cover were also missing which presented a shock hazard for anyone touching the exposed connections and there was no way to connect the str ... Read more ain relief. I disconnected the old 3 prong cable, removed the old terminal block, installed the new terminal block (required opening the dryer top for access), threaded power cable through bracket and fastened with strain relief leaving loose, attached the neutral/ground wires to middle terminal connection point, red to red wire in terminal block and black to black wire also in terminal block and tightened bracket and added cover.

I removed the gate in the back and found the belt had snapped. I continued to dismanlte the entire dryer to see what else was damaged. I pulled the drum out and ran the unit to make sure the motor didn't burn out and that the heater coil worked, which both did (I had no idea, this unit came with the house I purchased. They told me is was ... Read more broken.) So after finding the belt broken I saw that the top felt guide was rubbed down so far that the plastic guides where in paper thin, craked pieces.

I used the manuel that came with the felt guide to glue the new one on. If you do not replace the lower felt guide as well, make sure you mash the top felt down so that it's level with the lower felt. after I got my unit assembled the top guide pulled away because I didn't do this.
Installing the belt is timely, but easy. remove the drum then lay the belt around the visible line that the old one creates. Use this site's diagram to affix it to the pull and motor and that's that. Rotate the drum with your hand to even the belt out all around the drum to prevent it wobbling. I did this installation by myself, but it would have been much much easier if I had a set of hands on the other side of the unit.
Parts all fit together by either sheet screws or clips. Just keep track of which screw goes where. some are different sizes.

Used nut driver to remove screw and cover from dryer cord terminal block, used screw driver to remove two screws securing old terminal block, cut dammaged wire and stripped wire back and crimped on new terminal connecter, replaced old terminal block with new one, replaced two screws, installed new cord, and replaced cover plate and screw.

followed video and replaced part( cleaned and vacuumed dryer while I had it apart),relatively easy repair

Based on all of the other posts, their explanations were right on, so I won't repeat it here. You could probably do this repair on your own, but it helps having someone to hold the drum while reattaching the screws. I replace the rear drum bearing assembly and the belt. I would recommend replacing the belt. I almost didn't, but I'm gla ... Read more d I did. Once I had it off, I could see the cracks in it.

When installing the new bearing, make sure that you pack it with the supplied grease. Be liberal with it. I used what left over grease I had to grease the idler puller bearings too.

The dryer works perfectly now, with no squealing. My experience with Parts Select was flawless. The shipping was extremely fast, and the parts were as described. Finding the correct parts was a snap thanks to their easy to use web site.

Dryer door would not close, part had broke and fallen in. Once part was received it took less than an minute to put the new one in and I was back in business.

thanks for making it easy to find the part needed. and the delivery was fast!

bonnie J.

Rear plastic drum support bearing got worn making the shaft come in contact with the metal bearing bracket. That contact created a groove overtime and eventually snapped the shaft tip off.

Cut power off. Remove all the screws from the front panel. (where the controls are) working from the bottom to the top. Insert putty knife b ... Read more etween the dryer and the control panel and push down to release. Carefully disconnect the wire harness.
You will find 2 screws at the bottom and 4 on top holding the dryer door. Remove and expose the drum.
Remove the drive belt
Remove the drum.
You need a 5/16 nut drive to remove the bearing bracket and an extra set of hands to hold the support from the back.
Re-install the parts. I used bearing grease to make it run smoother
Attach the new shaft to the drum and reinstall the drum (its best done with help)

Re install everything back again. And you are done

I noticed for sometime that my dryer had been sqeeking...but I had thought nothing of it. It got alot louder as time went on and then one day the drum stopped spinning. Not to mention I had my son's 5th birthday party in 3 days. So I went online and found parts select. They sent me the whole assembly and I got it the day before the bir ... Read more thday, and it only took me 30 mins to replace it. Thank you, Parts Select for the prompt response and saving me for the embarrasment of having clothes all over the floor.

Basically, i followed instructions on 1 video i seen, but was able to shorten repair by not removing drum, and was still able to access the thermal limiter switch to remove old one and install new one. Worked like a charm. Thanks Dan

removed the old selector knob just pulled it out gently and lined up the new selector knob and gently pushed it into correct alignment. what a breeze.
reasonable prices. saved me $ on a service call, part, and labor. Thank you M



I just feel the postage is way too much for an item that weighs under 1 oz.

only needed to attach knob with one hand.