DE180 Maytag Dryer - Instructions

Safety first, so unplug the dryer. Next remove the two phillips head screws @ lower left and right front corners and take the front panel off. You will have to disconnect the door switch sensor wires which are yellow and white, marking the sensor so you can replace correctly. Next remove the front tumbler assembly with 4 screws, two on each side. Be sure to remove the automatic dry sensor wires. Then remove the belt by either reaching un under the tumbler and releasing the tension or taking the back access panel off w/ 4 screws and releasing the tension. Then once the belt is loose you can remove the tumbler. Then remove 2 screws and take the thermostat cover off. I removed the multi-temp thermostat w/ 2 screws rather than unhooking the wires and I did the same with the thermal fuse. Next remove 1 screw out of the blower housing cover and the 2 screws from the motor support. Once loose you can pull the motor out a little and unhook the wiring. Once out you will need to remove the pulley, blower housing and fan, and replace on new motor and put the new motor on the motor housing. Replace in reverse order and you should be done.

Just placed the new filter in place. Fit fine and works well.

1 Disconnect dryer from electrical outlet
2 remove vent pipe
3 Tilt dryer backwards and remove front cover bottom 2 philips screws.
4 remove lint assembly and then the fan blower housing with nut driver.
5 with pliers remove retainer clip from fan
6 remove snap ring with pliers or a flat blade screw driver will also work.
7 remove fan
at the same time I replaced the front glides if you do not want to do this then reinstall in reverse order and job is complete.

for glide replacement
1 remove the 4 screws holding the outer ring to the frame of the dryer.
2 drill out old rivits from the back side and then knock out. be careful to only drill rivit and not into metal frame
3 install new new glides makesure you install in correct direction.
4 install pop rivets with stud end on top side of glide. pushing rivet through glide and into the frame ring.
5 pop rivits and make sure they are secure.
6 reinstall ring making sure seal is around ring correctly
7 reintal 4 screws.
8 follow reassembly of blower and lint housing if you changed the fan. if not then just the lint assembly.

good luck the job is really easy and you will save yourself some money

The repair itself was pretty easy. Though I had figured out what needed to be done on my own while I waited for the belt to arrive via Fed Ex, the belt arrived with instructions that described the plan I had already figured and if I hadn't known what I was doing, the instructions would have been a great help.

STEP ONE, UNPLUG THE UNIT (and/or shut off the gas supply), CAREFULLY. Then, I took the front of the unit off by removing the 2 screws on the front panel near the bottom of the unit and disconnected the wiring that shuts the unit off when the door is opened. Set the front door panel aside. Then I removed the front of the tumbler retainer along with the exhaust duct and lint screen assembly by removing 4 screws that affixed the reatiner frame to the rest of the outer cabinet. Set this aside as well. Remove the entire tumbler unit. Set aside. Remove 4 screws on the back of the unit that hold the tensioner and motor access panel and remove it. Set it aside. At this point, I vacuumed every bit of lint and debris from the snapped belt out of the enitre unit, lubricated/greased all moving parts, cleaned off the friction bearing surfaces, and collected loose change ($1.35).

When the belt arrived, I unwrapped it, and placed the smooth side to the tumbler and rubber banded the slack off to the bottom right side (sort of the 4:30 position as you put the tumbler back into the unit). I carefully jimmied the tumbler back into the unit BEING CAREFUL not to pinch the groved belt between the tumbler and any other parts inside the cabinet. I replaced the tumbler retainer and screwed the 4 bolts back into place. I spun the tumbler over near the tensioner assembly (so I could see the slack through the access panel hole in the back) and removed the rubber band. I threaded the belt through the tensioner and over the drive pulley and rotated the tumbler clockwise to align the drive train of the belt. I plugged the 2 wires back into the switch on the inside of the door panel and then I replaced it on the front of the unit and screwed the 2 screws back in at the bottom front of the panel. I plugged the unit back in and tested opperation. It worked great! I unplugged the unit again (I'm not finished yet). I then replaced the access panel on the back of the unit and screwed the 4 screws back in. I moved the unit back against the wall and plugged it back in. Done! The dryer is less noisey now and more efficient most likely b/c I cleaned all the lint out of the thing! Thanks for the prompt shipment of the belt!! I'll get a few more years out of this dryer before spending $700 on a new one!!! Thanks again!

First I unplugged the dryer! Then unscrewed the two screws at the bottom of the front door. To remove the front door, swing the bottom up about 30 degrees until the two triangular hooks at the top of the door release. Then release the two wires going to the door switch from their harness so as to gain more slack to move the door out of the way. The switch was secured by 2 hex head sheet metal screws1/4inch in diameter. I used a small right angle socket wrench to get these loose. I only had to remove the front screw completely to be able to take the switch out for exchange purposes. Once this was done, reverse the process and plug it in! (BTW, the electrical schematic for this dryer is up under the top console)

replaced high limit thermostat-303396 and cycling thermostat-306056 approx $48.00. Remove dryer door with 2 screws in hinges and 2 screws on other side.Remove front panel-pull out from top-swing down to unhinge from bottom hooks to expose parts lower front. Small socket for high limit thermostat bolts@heating element housing and same socket for cycling thermostat@blower
exhaust air housing-both easily accessible in front lower area.Unplug power before working inside.

Removed front of Dryer, using screw driver and putty knife to push in the top clips. Front drops down. Disconnected wires to heating element. Then removed whole heating element chamber. Removed old heating element from chamber. Then installed new heating element insude of old chamber. Reinstalled chamber in dryer. Hooked up all wiring. Note! Dryer "must be unpluged" before starting any work! Last step reinstall front of dryer. Repair complete!

Removed the screws and took the door off then took the front panel off and popped up the top. Then pulled the drum out. Took snap ring pliers and removed rollers and replaced with new rollers then vacuumed all lint from machine and reversed operation to put everything back together. Operation was a total success!

Repair was simple after I found out how to get access (via 4 screws on the top edge). The plastic plug at the dial center was pried out & screws securing timer dial removed. The screws securing the timer were behind the dial plate. With the old timer out the wires were carefully swapped and the system reassembled.

Followed the instructions on the video, and saved 500 hundred dollars. I was already shopping for a new dryer. Thanks so much!

Took off back cover, thermostat was easily identified because of photos I've seen on website. Took 2 connectors off, removed 2 screws and removed old thermostat. That was pretty much it!

NOTE: Replacement thermostat 694674 has an adjustable temperature range setting that MUST be manually set prior to installing! You need to use the enclosed chart to find your original part# and make sure the setting is matched. My original part# 341146 had a "D" setting so I had to change but very easy to do.

First I unplugged the machine. I removed the two screws in the front panel and tilted the bottom of the panel out unclipping it at the top. I removed the lint duct whichis held in place with several 1/4" hex head screws. Then I removed the blower cover, also held on wth 1/4" hex head screws, exposing the blower wheel. Using snap ring pliers I removed the snap ring at the end of the motor shaft. Using needle nose liers I removed the spring clamp around the center hub of the old blower wheel and pull the blower wheel off the motor shaft. After cleaning as much lint out as I could I put the new blower wheel on the motor, secured with spring clamp and snap ring. Then I put the blower cover and lint duct back on and put front panel back on.

Unplugged the dryer!!!! Removed two screws from lower front panel. Pulled bottom of front panel forward which allowed clips holding top of panel to release. Unlcipped wires attached to door switch on front panel. Set aside front panel. Removed 4 screws(2 on left & 2 on right) from the drum retainer ring. Set aside retainer ring. Removed thin metal cover protecting blower wires. Removed several screws holding blower cover. Note blower is located on lower left below the lint screen. Used snap ring pliers to remove snap ring securing old blower wheel(an external snap ring). Removed old blower wheel from motor shaft. Inserted new blower wheel on motor shaft. Replaced snap ring. Replaced blower cover. Replaced thin metal wiring cover. Replaced drum retainer ring. Reconnected door switch wiring. Replaced front panel. Done. A hint on the maytag dryer. If your drum wiggles out too far the belt on the drum might not stay aligned. There is a groove on the drum...the belt should NOT sit in this groove...it should ride on the drum about an inch in front of the groove!!!

popped out old female clasp on dryer itself with screwdriver, undid 2 screws on dryer door and door handle with phillips screwdriver, popped in new male clasp part, put door knob back on and put the two screws back in door and it was all set to go. Less than 15 minutes to do. Better than new and wife is happy. No more duct tape holding door closed now.

Using the instructions accompanying the belt I bought from you,I removed the casing an front support for the drum. I then tried to follow the instructions to install the new belt from the front and found it to be absolutely impossible.I saw that there is a removeable plate on the lower right corner of the back that,if removed, would expose the motor and idler pulleys that are the object of the installation so I removed it and,without much difficulty, installed the belt. One problem in doing so involved the belt's tendency to slide into the groove in the drum when manipulating it onto the pulley set so I enlisted the aid of my wife to hold it in place from the front while I successfully and rather easily did so.