110C71182011 Kenmore Dryer - Instructions

Had to completely dismantle the dryer including the motor and grind off the.bolt holding the fan blade on. I did not realize it was threaded on with a left hand thread.Then reassembled.

I followed disassembly directions found on youtube and replaced th two-piece ring bearing that was identified by a parts diagra fron PartSelect. The repair was easy. Fix time was about thirty mionutes.

After removing the exhaust pipe and clamp, I unscrewed the back panel with a 1/4 inch drive socket set. That exposed the wires and the wiring skematic. I used a multimeter to track the power to the element and found that no power was reaching the element. I then unplogged the unit removing all power and tested the resistance on each therm ... Read more al fuse. The lower fuse had no resistance and the upper fuse did. I then disconnected the upper fuse, used a jumper wire the connect both wires together to bi-passed the fuse. I reconnected the power and turned on the dryer. The dryer element worked, confirming my suspicions of the bad fuse. Once I ordered the fuse and only paid for regular delivery I had the fuse with 24 hours and dryer back together within very little time. It took me more time to clean up the lint dust then it did to fix the problem.

Replaced roller. Very simple. Dryer is the easiest appliance to repair. Only a few parts keep a dryer working

after i got the replacement filter, it fit perfectly. the filter is white & my dryer is beige but i don't care...i'm just happy i have a good lint filter again, for my at least 30 year old dryer....thanks part select!

After watching the U Tube video to replace flywheel, I had a appliance repairman come to my home to install flywheel. There was no way I would have been able to put the dryer back together without some help.
I want to say "Thank You" to the sales representative who assisted me when purchasing my items, she was very patient while run ... Read more ning around the house looking for the model number of the dryer.

unplugged power, slide unit away from wall, removed bottom front cover, rear sheetmetal cover, tilted front of unit to remove roller outboard support (sheetmetal screw from bottom of dryer). Removed shaft bolt from rear of dryer which released roller assembly. Remove speed nut from old roller assembly to remove outboard support arm, mount ... Read more ed new roller to new shaft placed triangle clips (one each side of roller), mounted outboard support to front of new shaft and completed re-assembly (reverse order of disaasembly).

lifted top section of dryer
removed front dryer panel
removed drum belt and tensioner
removed both drum rollers
cleaned both roller axles
installed new rollers
reassembled remainder of dryer
if you are at all mechanically inclined, it is a simple job

Removed the drum then removed the old parts and installed the new ones. Dryer now runs very quite and heats good. You have very fast service my mother ordered the parts on the net one day and I received the parts next day and did the repair that night and dried clothes. Thanks,

Your great service is very hard to find.

I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.

Read this site and saw many fixed the problem with a new thermostat. Ordered one and it was simple to replace. Just removed the back panel of the dryer and the thermostat is right there. Two screws to remove it, swap the four wiring plugs onto the new one, reinstall it. Unfortunately that didn't fix it so went back online and ordered the ... Read more coil kit, another common solution. Removed front of dryer by removing the two screws the hold the lint trap onto the top and the two hinge plate screws on back of dryer to tilt the top up ward and backward. Removed two mounting screws on inside of dryer front and slip front panel upward to remove. The coils are right in the front down at the bottom left of dryer.Used an offset screwdriver to remove the two screws holding them in place. They slide right out, one has two prongs, one has three. Replace them with the new coils and put them back in place. Reassembled and everything works now. Grand total of eight screws removed and replaced, pretty simple. I'd recommend buying two or three parts if you see several parts as possibilities for a repair. Easier than doing it the dummy way like I did!

I replaced a bad thermostat

just remove 4 screws removed the drum and put the affected part and that's it

Followed the video and stopped at each part not one issue very easy repair most difficult was separating the electric from from panel a little tricky to get apart.

Unplugged dryer, removed back panel, checked thermostats & heating coil with ohm meter, found one stat with broken terminal and one that was bad. Ordered them from this site. Received them in record time, did the installation and was back in business drying clothes. Thanks for video & great service.