110C71182011 Kenmore Dryer - Instructions

All Instructions for the 110C71182011
76 - 90 of 366

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Needed a new lint filter
3 of 3 people found this instruction helpful.
  • Evelyn from JACKSONVILLE, FL
  • Very Easy
  • Less than 15 mins
Took the old one out, replaced it with new one.
Was this helpful?
Thank you for voting!
timer control would get stuck
3 of 3 people found this instruction helpful.
  • Joseph from LINCOLN, RI
  • Very Easy
  • 15 - 30 mins
  • Nutdriver
Bought the part and removed 10 screws unplugged the wiring and applied it to the new part. Reassembled, done.
Super easy, works great!
Was this helpful?
Thank you for voting!
dryer would not work .
3 of 3 people found this instruction helpful.
  • Tom from MEARS, MI
  • Really Easy
  • 15 - 30 mins
  • Socket set
Took the old parts out and installed the new parts in , everything that you sent fit perfect!!!!!
Was this helpful?
Thank you for voting!
The drum made a lot of noise while turning. The dryer shook
3 of 3 people found this instruction helpful.
  • Craig from VASS, NC
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers, Socket set
Used the video to remove the top and front. Removed the drum. Removed the spindle through the whole next to the spindle. Vacuumed a ton of lint in the dryer and vent pipe. Reassembled in reverse order. Easy repair and a good time to clean the lint.
Was this helpful?
Thank you for voting!
No heat
4 of 7 people found this instruction helpful.
  • James from Randsburg, CA
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
I had two dryers, one was gas and the other was electric. The electric stopped heating. So I rolled out the gas dryer, but it was setup for natural gas and at this location, I only have propane. So I changed the jets to work with propane, in the process I broke the igniter, so I replaced that and that made the propane one work. Armed with the knowledge from that job, I took the electric dryer apart located the thermostat and replaced that and low and behold I have two working dryers. One for now and one for an emergency. I only have four screws left over!!!! Jim Cooke
Was this helpful?
Thank you for voting!
no heat
3 of 4 people found this instruction helpful.
  • DAVID from DANVILLE, VA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
unplug the dryer used nut drive to take the back off unhook the hose from dryer . disconnect the wires. remove the 2 screws from thermal cut -off . install the new parts
Was this helpful?
Thank you for voting!
gas flame would shut off after + or - two minutes
3 of 4 people found this instruction helpful.
  • RICHARD E from UNALASKA, AK
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers
the igniter worked so replaced the two coils on the burner, did not help, read the diagram that came with the machine and replace the high limit cut out. that did it, however the mounting bracket needed to be modified by grinding a tab off, so that the cut off switch would fit in to the bracket.
Was this helpful?
Thank you for voting!
Bulb worked for a couple days and has now burned out, filaments dangling
3 of 4 people found this instruction helpful.
  • Amy from JUNCTION, TX
  • Easy
  • Less than 15 mins
  • Screw drivers
To replace the light bulb, I removed the screw and the cover, unscrewed the old bulb, replaced with the new bulb and replaced the cover, securing it with the small screw. It worked appropriately with normal use for a few days and then I noticed the light was not coming on when I opened the door.

I removed the cover and pulled out the bulb to find that the filaments inside are dangling and burned through. I need them replaced, please.
Was this helpful?
Thank you for voting!
Thermal Cut-off was bad
3 of 4 people found this instruction helpful.
  • Timothy from Fort Payne, AL
  • Really Easy
  • Less than 15 mins
  • Nutdriver
The repair was no problem. Just taking off the hex screws removing the crimp wire and replace the parts in the kit and the old dryer came back to life again.

Thanks
Was this helpful?
Thank you for voting!
Terrible noise coming from the rotation of drum
3 of 4 people found this instruction helpful.
  • Leo from MERIDIAN, ID
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Took apart front of cabinet, set aside. Undid the belt drive. Removed the drum. Noticed rear seal was with large gap where it wore away, causing the lint to leak onto the interior of cabinet. Ordered a new seal, removed old seal, prepped for new seal. Used spring clamp to hold new one on place. Applied the glue to hold seal in place waite d 24 hrs to dry. Reinstalled drum, put cabinet back together. Plugged in ran whisper guiet.
Was this helpful?
Thank you for voting!
Dryer heating up but clothes not drying
3 of 4 people found this instruction helpful.
  • Donald from Knoxville, TN
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
Removed back and then removed lint slide.
Vacuumed all of the cabinet and and washed lint chute.
Blower seal and lint seals were crumbling since dryer is 24
years old. Part Select diagrams and repair videos are extremely helpful in showing the process. Dryer now working like new.
Was this helpful?
Thank you for voting!
the lower drum support roller had been chewed to bits.
3 of 4 people found this instruction helpful.
  • Rodney from Mt. Jackson, VA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers
I pried open the top of the dryer, removed the 2 scrws holding the front cover of the dryer, un hooked the dryer drum buide belt, removed the dryer drum - all this just to get to the drum support roller. The bottom roller - the rubber on the wheel had been "chewed of". I can only guess because too much weight was placed in the dryer with wet clothes.
I removed the triangle shaped retaining clip, using the mini flat head screw-driver, slid the damaged roller off, replaced the new roller, and installed the new retaining clip. To install the new clip, I used a 1/2inch nut driver. I did the same to replace the upper drum support roller. The actual repair took less than 5 minutes, However, the prep time in dismanteling the dryer in order to get to the drumm rollers and puting the dryer back to gether consumed the bulk of my time.
Was this helpful?
Thank you for voting!
The sound was like a cement mixer
3 of 4 people found this instruction helpful.
  • Russell from Apache Junction, AZ
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
When i finally got sick and tired of hearing it when she used the dryer. I popped the top flipped it up unscrewed the 2 screws holding the front panel of the body on, picked up on it and pulled it off the drum. I then reached back to the rear right corner and stretched the tentioner and pulled the belt off the motor pulley.Then I picked u p the belt and the drum and pulled it out of the dryer body. After seeing the drum support roller that is mounted on the base, and back of the left side I decided to go online and find this sight that had the drum support rollers as a set with the keepers and the push nut for the brace as a set for a really fair price. If your unit has a warranty "do not" take anything apart and do not order any pats until you check with your dealer. You do not want to void your warranty. I then pulled off the push nut and then i took the screw that held on the brace in front of the worn out drum roller, then pryed off the keeper and pull off the drum roller, took off the back keeper;inspect the shaft if it is not damaged ,(this one was not),then you wait until the parts arrive, yes your dryer will set in parts for about a week, but believe me in todays economy its worth "not having to buy a new dryer" at least for this small repair. When the parts arrive everything is pretty much in reverse of how you took it apart dont forget your cell phone is also a camera that can be a "memory enhancer" for when you get this far. Also be nice to your wife your going to need a little help putting it back together. Of course if she wants her dryer back she needs to help anyways. patience is a virtue and if you dont take your time and do this right it will be tested the drum and belt need to be fitted right and held up to get both the belt on the pulley and around the tentioner and get the front panel lined up on the front of the drum good luck and pass your knowledge on its getting to be a lost art.
Was this helpful?
Thank you for voting!
First taking too long to dry, then no heat at all.
3 of 4 people found this instruction helpful.
  • Shelly from Flagstaff, AZ
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Socket set
Unplug the machine. Take off back panel and remove heater assembly. Since I was already into the heating system, I replaced the heating element as well ($30). I replaced the old thermal cut off and overtemp, put the wires back on the connectors, reassembled, and the dryer works like it did when brand new! Within 30 minutes the repair was completed. Still saving for a new front loader washer/dryer, so the repair will hold us until we have enough to buy new. Alos, helped us to need to dry clothes on a clothes rack in the house. Good practice and lesson for the entire family!
Was this helpful?
Thank you for voting!
one of my rollers fell to pieces
2 of 2 people found this instruction helpful.
  • james from Fredericksburg, VA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
just like the guy in the video. It was easy to folow his instructions, and the best thing of all i could stop the video if I had a question and then resume!
Was this helpful?
Thank you for voting!
All Instructions for the 110C71182011
76 - 90 of 366