110C71182011 Kenmore Dryer - Instructions

All Instructions for the 110C71182011
46 - 60 of 366

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer was taking twice as long to dry as it used to.
6 of 6 people found this instruction helpful.
  • Glenn from East Brunswick, NJ
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Took of the back cover, and removed the vent connecting the blower motor to the drum. It was completly full of lint, so cleaned it out completly, and tried the dryer again. The heater element was still cutting off early, and the clothes were not getting very warm, but better than before. Decided to change the thermal cut-off switches. Ordered the parts on Sun, they came in on Tuesday. Dryer was up and running Tuesday night. Just 2 screws per switch, took less than 1/2 hour. The dryer now runs like brand new, and my wife was ready to fork over $800 for a new one!
Was this helpful?
Thank you for voting!
Dryer would run, but no heat.
7 of 9 people found this instruction helpful.
  • William from Galion, OH
  • Really Easy
  • 15 - 30 mins
  • Socket set
First I did a search on dryer repair. Found a website that described easy things to check with an ohm-meter. I then performed the continuity checks on the items and found the high-limit one was open, in other words, no good. It works similar to a fuse. All this was done after removing the back panel, just a few screws. The reason it exce eded the high limit, possibly because I never opened the back up and cleaned it. Found out it should be done every couple years. My vent line had a hole in it and was letting lint get drawn into the heating element, could have been a fire.
Was this helpful?
Thank you for voting!
Lens melted because paper got behind the lens and was heated by the lamp.
6 of 6 people found this instruction helpful.
  • Chris from Valley Stream, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
1 screw to replace.
Was this helpful?
Thank you for voting!
Dryer would stop after a very short time when cold, wouldn't keep running at all when hot
6 of 6 people found this instruction helpful.
  • Paul from ANTIOCH, TN
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
At first I was advised to replace the temperature overload sensors, which I did but didn't fix the problem. After adding the additional information that the dryer would run to full cycle as long as the Start switch was held in I was advised to replace the Start switch.

It wasn't obvious from the wiring diagram, but if you remo ve the Start switch and look at the side it shows it contains a solenoid holding circuit that keeps the switch in the "on" mode as long as there is a feedback signal from the temperature overload switches. So if the dryer will run to completion if the switch is held in, replace the Start switch. If it still stops mid-cycle, replace the temperature overload switches.

The replacement videos were spot on as far as clear and easy to follow instructions for the repair, and all ordered parts were delivered very quickly.

Thanks for your help PartsSelect!
Was this helpful?
Thank you for voting!
dryer had no heat
6 of 6 people found this instruction helpful.
  • gary from newcomerstown, OH
  • Really Easy
  • Less than 15 mins
  • Nutdriver
My Whirlpool dryer had no heat. I removed the back panel and within minutes diagnosed the problem to a blown thermal cut-off fuse. I ordered a thermal cut-off kit on a Sunday night and had the parts at 7:30am Wednesday morning. Total time for diagnosing and repair was no more than 15 minutes. PartSelect saved me a ton of money and aggrava tion!!! AWESOME!!!!

Gary
Was this helpful?
Thank you for voting!
No Heat
7 of 9 people found this instruction helpful.
  • Ken from Bixby, OK
  • Easy
  • More than 2 hours
  • Nutdriver, Screw drivers, Socket set
Thermal fuse was blown so I replaced it. Still no heat. Hi-Limit thermostat and Cycling Thermo. had continuity as did flame sensor. Igniter tested 66ohms. I placed a wire jumper across the Hi-Limit and the igniter glowed, solenoids opened and gas came on. I orderd the Hi-Limit and since both "overheating" limiters were defective I de cided to order the cycling thermo just in case. The Hi-Limit was received in 2 days but the Cycling Thermo was backordered. In the meantime my wife got antsy so I went ahead and installed the Hi-Limit and put her back in service... ...for one load. I wasn't certain if I had fried the "limiters" again but since they had continuity and I could measure continuity all the way to the Igniter I decided that it HAD to be the cause. I ignored the flame sensor since it never came into play without the igniter glowing... The igniter arrived and measured 56ohms. Hmmm... After installing the problem was solved. Word of advice: If the thermal fuse is blown and even if all else in the circuit SEEMS ok, go ahead and order the Fuse, Hi-Limit and Cycling Thermos, and the Igniter. It will take you about 30 minutes to install and you'll reduce your out-of-service time! Good luck!
Was this helpful?
Thank you for voting!
Dryer got hot then heat would shut off
6 of 7 people found this instruction helpful.
  • Douglas from Fernley, NV
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Socket set
Sensor is in the front lower left. Gas off, electicity off. Removed two screws for the filter, pry/lifted the top up and taped it too the overhead cabinet, removed two screws inside top of front panel, lifted pandel with door closed staight off. Two screws to remove the flame sensor braket. unplug the old sensor install the new one and r everse everything. With others suggestions I purchased temperature switches etc. but the radiant flame sensor was the problem. I now have some spare switches for future. Excellent company and very quick service. Oh, Sears wanted 200.00 just for the service call, I live rural.
Was this helpful?
Thank you for voting!
Dryer not Heating
6 of 7 people found this instruction helpful.
  • Brigitte from Westerville, OH
  • Easy
  • 15 - 30 mins
  • Nutdriver
Was not sure what was wrong but the Part Select site allowed us to view other repair issues and solutions. We ordered the kit, it arrived the next day (how is that possible) and easily put the parts in and chaching...money saved and dryer works better than ever. THANKS PartSelect, we give you an eleven and we will recommend you to everyon e.
Was this helpful?
Thank you for voting!
not heat
7 of 10 people found this instruction helpful.
  • Sarah from Merrimac, MA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
For the Ignitor - As involved as taking the dryer completely apart sounded, it was super easy. 1-take out the lint trap and remove the two screws there. 2-Pop open the top with a screw driver and swing the top completely over/back. 3- remove the two screws holding in the front panel and remove the panel. 4- loosen the belt by pushing on t he tension roller under the drum on the right and remove the drum (its super light) use the belt as a handle. 5- remove the screw holding in the ignitor and replace it with the new one. Be careful to not touch the new ignitor. Then go backwards putting it back together.
Was this helpful?
Thank you for voting!
The landry would not dry all the way at the end of the cycle.
8 of 14 people found this instruction helpful.
  • Mark from Houston, TX
  • Easy
  • 30 - 60 mins
First i removed the rear panel on the dryer.the removed bothe thermostats that were on the blower housings.unpluged all wiers and installed new thermostats.reinstalled the wiers in there proper locations...note to log the location of the wires when removing from old switch.reinstalled the rear panel and hooked dryer back up and test.
Was this helpful?
Thank you for voting!
No heat, would not light because igniter burnt out
6 of 8 people found this instruction helpful.
  • anthony from Port Arthur, TX
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Unplug dryer. Remove the front bottom panel of dryer 2 screws, then unplug wire connector to the old igniter then unscrew one screw holding ignitor then wiggle out. Open new igniter wiggle back in place insert screw tighten, (getting this screw back in is a little hard) replug wire connector to new igniter replace front panel with two scr ews. Plug in dryer and there you go drying clothes again. Wife all happy again.
Was this helpful?
Thank you for voting!
Motor was bad
5 of 5 people found this instruction helpful.
  • Michael from CLIFTON HTS, PA
  • Really Easy
  • 30 - 60 mins
I have not received the parts yet waiting on the motor, can’t put the blower fan in without the motor, ordered it , Jan 23rd, still no motor, have to go to laundry mat, have you ever had to do that with 7kids, and you and your wife’s laundry, probably not, because you would have had your motor by now. Maybe you can help me with the part s o I can redo a testimonial here for you. 19 days and still waiting
Was this helpful?
Thank you for voting!
Poor drying and took excessive amount of time to complete partially dried loads
5 of 5 people found this instruction helpful.
  • Stephen from LOUISVILLE, KY
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Took back cover off. Cleaned out the lint that had built up inside the dryer. Replaced the lint trap housing and lint chute seals. Also replaced the drying vent hose. Works great now.
Was this helpful?
Thank you for voting!
Dryer had no heat at all. This is an older gas dryer.
5 of 5 people found this instruction helpful.
  • todd from MILFORD, PA
  • Really Easy
  • Less than 15 mins
  • Wrench set
Cleaned out years of fuzz behind lower access panel and noticed where the igniter sits there is a metal tube about 1 inch in diameter. It had rust on the end and was starting to flake away. Found some helpful hints about how to test the igniter. Very easy, just used an ohmeter. Unplugged the 2 pin wire connector and checked for continuit y. 1 lead on 1 pin and the other on the other pin., igniter side not the harness side from the dryer. A good igniter should read less than 5 ohms. I don't know the spec. exacttly, but it should not read open or infinite resistance. My meter read an open circuit. Removed the tube and igniter assembly, mine only 2 small bolts. I found the igniter element cracked. Ordered and installed igniter and tube assembly. This was a very easy install. 20 year old dryer works great and it's better than spending $500.00+ on a new one.
Was this helpful?
Thank you for voting!
incessantly annoyingly squeaky dryer
5 of 6 people found this instruction helpful.
  • Douglas from Tiburon, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set
Take out 2 philips screws in lint trap holder on top. Use flat screwdriver to pry up front left and right of dryer top near outside edges and tilt up out of the way. Remove 2 push-on AC connectors on door switch and remove plastic clip holding wires to dryer's front top metal edge. Remove (2) 5/16" sheet metal screw on inside top left an d right edges to free up front panel. Lift front panel about an inch and it'll then pull off. It helps to have a second person to help hold or remove the drum at this point. It took 3 times for me to guess right on the squeak. First time I replaced the belt, second time I replaced these rollers, third and final time I replaced the idler pulley, the shaft of which had worn completely off so clearly i can't figure out how we didn't see (or hear) it the first two times! Dri-Slide lube helped stop the squeaking the first two times, but it always returned until this time, now I have a thoroughly rebuilt dryer for the next generation! (PS vacuum out the bottom of the dryer while it's open to remove both lint and greasy roller shavings - do this FIRST and you'll have cleaner hands & clothes!)
Was this helpful?
Thank you for voting!
All Instructions for the 110C71182011
46 - 60 of 366