110C71182011 Kenmore Dryer - Instructions

All Instructions for the 110C71182011
121 - 135 of 366

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
No Heat
1 person found this instruction helpful.
  • Michael from DAYTON, TX
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Wrench (Adjustable)
Removed back cover and replaced thermal cutoff, installed new push on terminals. Bolted back on and dryer is working like new again.
Was this helpful?
Thank you for voting!
Heat stopped after a few minutes
1 person found this instruction helpful.
  • Michael from LAKE FOREST, CA
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Read this site and saw many fixed the problem with a new thermostat. Ordered one and it was simple to replace. Just removed the back panel of the dryer and the thermostat is right there. Two screws to remove it, swap the four wiring plugs onto the new one, reinstall it. Unfortunately that didn't fix it so went back online and ordered the coil kit, another common solution. Removed front of dryer by removing the two screws the hold the lint trap onto the top and the two hinge plate screws on back of dryer to tilt the top up ward and backward. Removed two mounting screws on inside of dryer front and slip front panel upward to remove. The coils are right in the front down at the bottom left of dryer.Used an offset screwdriver to remove the two screws holding them in place. They slide right out, one has two prongs, one has three. Replace them with the new coils and put them back in place. Reassembled and everything works now. Grand total of eight screws removed and replaced, pretty simple. I'd recommend buying two or three parts if you see several parts as possibilities for a repair. Easier than doing it the dummy way like I did!
Was this helpful?
Thank you for voting!
would not heat
1 person found this instruction helpful.
  • Arthur from VALLEJO, CA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Socket set
I started by changing the part that had the highest percentage to solve this problem , the top three didn't work , the fourth part, the disposable thermostat, and the last one that could be done from the front worked.
Was this helpful?
Thank you for voting!
Dryer making excessive noise; then continued to blow circuit
1 person found this instruction helpful.
  • Ava from BALTIMORE, MD
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set
Attributed excessive noise to age of dryer, upon closer inspection, a dish towel had become caught at rear of drum because the drum support rollers were damaged causing the drum to create a space in the rear of the drum. This was large enough for the dish towel to be caught. Originally I thought that the thermal fuse had blown the circuit -which should occur in an overheating situation-however the loose drum had worn through the electrical wire leading to the door switch because it was not properly seated on the rear drum rollers. the wire was repaired with a wire nut, rear drum rollers were installed and it is working again. thank you for the extremely fast shipping
Was this helpful?
Thank you for voting!
rollers had been new too long!
1 person found this instruction helpful.
  • Scott from EVEREST, KS
  • Very Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Took of the btm pan and the top to be able to remove the front. Raised the drum enough to replace the right hand wheel. ( the old ones had already been removed) Replace the left hand wheel and bracket. Re assemble the machine. Worst part was trying to do all this with the can of beer in one hand!!
Was this helpful?
Thank you for voting!
dryer overheat
1 person found this instruction helpful.
  • Harry from BEVERLY HILLS, FL
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Replaced thermostat on back of dryer, very easy to do, took about 15 minutes after watching video . doe's not require rocket scientist to do.
Was this helpful?
Thank you for voting!
Gas dryer would heat but shut off as it warmed up.
1 person found this instruction helpful.
  • James from COLLIERVILLE, TN
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
Removed the back panel of the dryer. Thermostat is located in the out going air flow near the exhaust. Removed one screw that held thermostat. Exchanged wires and put everything back together
Was this helpful?
Thank you for voting!
Dryer would not heat and the timer would not turn as it should
1 person found this instruction helpful.
  • Jeff from OAKLAND, TN
  • Really Easy
  • 30 - 60 mins
  • Socket set
I replaced a bad thermostat
Was this helpful?
Thank you for voting!
remove, take off , install
1 person found this instruction helpful.
  • jose from SANDY SPRINGS, GA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
just remove 4 screws removed the drum and put the affected part and that's it
Was this helpful?
Thank you for voting!
Dryer wasn't heating
1 person found this instruction helpful.
  • William C. from BIRMINGHAM, AL
  • Very Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Unplugged dryer, removed back panel, checked thermostats & heating coil with ohm meter, found one stat with broken terminal and one that was bad. Ordered them from this site. Received them in record time, did the installation and was back in business drying clothes. Thanks for video & great service.
Was this helpful?
Thank you for voting!
Dryer was making a loud rattling noise and shaking
1 person found this instruction helpful.
  • Lindsey from Lancaster, PA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Wrench (Adjustable)
I watched the part select you tube video that links specific loud dryer noises to specific broken or loose parts. It allowed me to identify the part I needed, which I ordered through their website. Two days later, I had the part and installed it, with help from another online video that showed me how to take the dryer apart to install the drum support roller. Thank you, the information provided made the repair quite easy. It works perfectly now!
Was this helpful?
Thank you for voting!
My daughter threw a heavy wet comforter into the dryer and the tri-ring sheared off.
1 person found this instruction helpful.
  • Joe from St. Louis, MO
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.
Was this helpful?
Thank you for voting!
dryer was not getting hot.
1 person found this instruction helpful.
  • Sakina from Philadelphia, PA
  • Really Easy
  • Less than 15 mins
I ordered the necessary thermal cut off and fuse from Part Select. The process was easy, when i came home from work my husband installed the piece in a matter of minutes and we were back in business of drying clothes.
Was this helpful?
Thank you for voting!
Dryer was not getting hot enoug. I determined the higher thermostat was faulty.
2 of 4 people found this instruction helpful.
  • Tim from Bonham, TX
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Remove the back, just a few screws, after you unplug the dryer. Disconnect the wiring terminals to both the low and high temperature thermostat. Take both units out with a nut driver and replace. Reassemble the unit the same way it was dismantled. Partselect is a great place to order whatever you need. They almost got here faster than I could place the order. Great service, keep it up.
Was this helpful?
Thank you for voting!
Everything worked on the dryer,JUST NO HEAT!!
1 person found this instruction helpful.
  • Mark from Cicero, AL
  • Easy
  • Less than 15 mins
  • Nutdriver
Turned it on it's face,removed bottom back panel.Checked the heat coil and had closed circut. Checked the thermal cut offs one had a closed circut one open.So I orderd the kit ,replaced both . On with the panel,stood it up,plugged it in and WHALA!! Heat and happiness.
Was this helpful?
Thank you for voting!
All Instructions for the 110C71182011
121 - 135 of 366