110897 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer shutting off prematurely
3 of 6 people
found this instruction helpful.
-
David from CARMEL, IN
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
1. Popped off hinged dryer lid at front and supported to allow access to lint chute
2. Removed back sheet metal panel
3. Removed dryer chute to expose sensor; removed same-deformed terminal on top needs to be straightened with pliers to remove through slot.
4. Installed new sensor; terminal needs to be twisted to ensure so ... Read more lid installation and good ground. Bottom pops in but took a bit of finagling.
Accessing and replacing the sensor was straightforward enough; bulk of the job was cleaning off old gasket material (severely degraded) in two locations. Used plastic scraper and razor blade scraper, then cleaned sticky with goo gone. Installed new gasket strip from Home Depot; available in rolls. I used 1/4" x 3/8". Surprising how much lint/hair/debris was in bottom of lint chute. Glad to get it all clean.
2. Removed back sheet metal panel
3. Removed dryer chute to expose sensor; removed same-deformed terminal on top needs to be straightened with pliers to remove through slot.
4. Installed new sensor; terminal needs to be twisted to ensure so ... Read more lid installation and good ground. Bottom pops in but took a bit of finagling.
Accessing and replacing the sensor was straightforward enough; bulk of the job was cleaning off old gasket material (severely degraded) in two locations. Used plastic scraper and razor blade scraper, then cleaned sticky with goo gone. Installed new gasket strip from Home Depot; available in rolls. I used 1/4" x 3/8". Surprising how much lint/hair/debris was in bottom of lint chute. Glad to get it all clean.
Read less
Was this helpful?
Thank you for voting!
Dryer tumbler made a loud noise
2 of 3 people
found this instruction helpful.
-
jeff from albuquerque, NM
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
Disassembled dryer, removed tumbler, replaced drum support rollers
Was this helpful?
Thank you for voting!
drum support roller was squeaking VERY loud
2 of 3 people
found this instruction helpful.
-
joe from southgate, MI
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
lifted top section of dryer
removed front dryer panel
removed drum belt and tensioner
removed both drum rollers
cleaned both roller axles
installed new rollers
reassembled remainder of dryer
if you are at all mechanically inclined, it is a simple job
removed front dryer panel
removed drum belt and tensioner
removed both drum rollers
cleaned both roller axles
installed new rollers
reassembled remainder of dryer
if you are at all mechanically inclined, it is a simple job
Was this helpful?
Thank you for voting!
Worn bushing on bottom drum roller
3 of 6 people
found this instruction helpful.
-
Frank from Avon, CT
- Easy
- 30 - 60 mins
-
Nutdriver, Socket set
unplugged power, slide unit away from wall, removed bottom front cover, rear sheetmetal cover, tilted front of unit to remove roller outboard support (sheetmetal screw from bottom of dryer). Removed shaft bolt from rear of dryer which released roller assembly. Remove speed nut from old roller assembly to remove outboard support arm, mount
... Read more
ed new roller to new shaft placed triangle clips (one each side of roller), mounted outboard support to front of new shaft and completed re-assembly (reverse order of disaasembly).
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
The dryer nob wasn't working the dryer knob broke off inside the unit
2 of 3 people
found this instruction helpful.
-
WILLIAM from SEBASTIAN, FL
- Very Easy
- 30 - 60 mins
-
Pliers, Screw drivers
It was very easy to install the new parts successfully thanku parts select I will always keep using your business the representative was so helpful and understanding my problem I wish I could remember his name he was outstanding and a 100 thumbs up to him
Was this helpful?
Thank you for voting!
Loud noise while in use
2 of 3 people
found this instruction helpful.
-
Josh from Madill, OK
- Really Easy
- 15 - 30 mins
-
Screw drivers
Replaced roller. Very simple. Dryer is the easiest appliance to repair. Only a few parts keep a dryer working
Was this helpful?
Thank you for voting!
Dryer door would not stay closed
1 person
found this instruction helpful.
-
Gregg from St. Augustine, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
After removing front door panel (2 screws) I removed the old latch catch and replace with the new part. 4 minutes later, the door was back together, the dryer was running and the door was staying closed.
Was this helpful?
Thank you for voting!
Was too old
3 of 7 people
found this instruction helpful.
-
HELOISA from BOCA RATON, FL
- Really Easy
- Less than 15 mins
I just changed for the new one! 2 seconds.
Was this helpful?
Thank you for voting!
Seal snapped, which lead to longer dry cycles.
2 of 4 people
found this instruction helpful.
-
Christian from Sunapee, NH
- Really Easy
- Less than 15 mins
Just slipped it on, it was very simple. My dry cylces were reduced. Worth the $15 I spent to get the part!!!!
Was this helpful?
Thank you for voting!
dryer door wouldn't catch, catch was broken
1 person
found this instruction helpful.
-
Theodore from Tyler, TX
- Really Easy
- Less than 15 mins
took the cstch reciever out, with my fingers, pushed the new one in, snap lock fit.......couldn't be better, like repairing a model T ford.......
Was this helpful?
Thank you for voting!
broken door catch
2 of 4 people
found this instruction helpful.
-
Michael from Goddard, KS
- Really Easy
- Less than 15 mins
the part fit perfectly, it just snaped right into place.
Was this helpful?
Thank you for voting!
broken door catch
1 person
found this instruction helpful.
-
Frank from ENDICOTT, NY
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
Took 3 screws out used the putty knife to pry the door a part then used the pliers to remove the old door catch and then sapped the new one and put the door back together and I was was done in less than 10 min.
Was this helpful?
Thank you for voting!
latch was broke
1 person
found this instruction helpful.
-
Rick from SAN DIEGO, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
just followed the video directions, worked perfectly thanks
Was this helpful?
Thank you for voting!
dryer would not run because catch did not hold tight enough to press door switch.
1 person
found this instruction helpful.
-
j from TAZEWELL, TN
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
removed screws that held the door face to gain access to catch replaced catch reassembled door tried dryer works great!
Was this helpful?
Thank you for voting!
Door catch was cracked
1 person
found this instruction helpful.
-
Tammy from glenford, OH
- Very Easy
- Less than 15 mins
Incredibly simple! You just pop the other plastic catch out with a butter knife and pop the other on in. This is the second time I have done this over the last 4 years or so.
Was this helpful?
Thank you for voting!