110897 Kenmore Dryer - Instructions

All Instructions for the 110897
61 - 75 of 275

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
The dryer just stopped working. Couldn’t get it to start.
3 of 3 people found this instruction helpful.
  • Anita from WILKES BARRE, PA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Watched a you tube video that told me exactly how to do it. Saved us from going out and buying a new one. My husband and I were very proud of ourselves because just to get someone to look at it would have cost us $85. The part was only around $25.
Was this helpful?
Thank you for voting!
Lint filter on dryer had broken apart
3 of 3 people found this instruction helpful.
  • Julie from TUSCARORA, NV
  • Really Easy
  • 15 - 30 mins
Replacement fit perfectly.
Was this helpful?
Thank you for voting!
The friggin thing wouldn't shut off when you opened the door. The switch dealie was just hangin there like a loose tooth.
3 of 3 people found this instruction helpful.
  • Steve from DES PERES, MO
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
The videos showed the tech taking the front off the unit but my unit didn't play that game. Instead all I had to do was take the top loose, (don't forget to take the dryer vent screws out first, that was the first beer) then access to the switch was easypeezy. That coupling for the switch assembly was 2 beers long. Anyways, got it all bac k together and it works like it's suppose to.
Was this helpful?
Thank you for voting!
Rear drum rollers were shot.
3 of 3 people found this instruction helpful.
  • David from JOLIET, IL
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
I followed the instructions on the video and it was simple. The hardest part was vacuuming out 32 years of lint from around the motor and igniter. I was lucky there was never a fire in the dryer.
Was this helpful?
Thank you for voting!
Dryer was working erratically.
3 of 3 people found this instruction helpful.
  • Alejandro from HOLLIS, NY
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set, Wrench (Adjustable)
I followed the YouTube video. Took the back panel off, took the lint thing off and proceeded as indicated in the video excerpt I didn't take the top off.
Was this helpful?
Thank you for voting!
start switch replace
3 of 3 people found this instruction helpful.
  • john from GERBER, CA
  • Very Difficult
  • More than 2 hours
  • Screw drivers
i could not perform the repair because despite using the proper id numbers, i received the wrong parts from kenmore three times in a row. now i am trying to return the wrong parts which cost me 120.00 for the start switch, and the knob for the switch, so far. the switch was 40.00 the simple plastic button was (wrong) 40.00, and the wrong unidentifiable part, suposedly correct one, which also was 40.00. this, with the original 40.00 wrong switch amounted to the 120.00 that i am still trying to have returned. otherwise, the fix should be quick and simple, o yeah, its been three months.. you tell me if i am satisfied....
Was this helpful?
Thank you for voting!
The drum made a lot of noise while turning. The dryer shook
3 of 3 people found this instruction helpful.
  • Craig from VASS, NC
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers, Socket set
Used the video to remove the top and front. Removed the drum. Removed the spindle through the whole next to the spindle. Vacuumed a ton of lint in the dryer and vent pipe. Reassembled in reverse order. Easy repair and a good time to clean the lint.
Was this helpful?
Thank you for voting!
a broken belt
6 of 12 people found this instruction helpful.
  • Dorise from Donalsonville, GA
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Pliers, Socket set, Wrench (Adjustable)
my hany man did it....
Was this helpful?
Thank you for voting!
Dryer drum wouldn't turn and motor would shut off
3 of 4 people found this instruction helpful.
  • Cynthia M from Westfield, MA
  • Easy
  • More than 2 hours
  • Screw drivers
First I was told by the maytag repair man that the motor was shot and it would be 467 dollars to repair. Since I didn't have that kind of money I decided to take it apart to see if I could replace the motor myself. Once I had it apart I saw the part that held the motor in place was broken off and the motor was out of place causing it too shut itself off. Once I figured it all out it took about 2 minutes to replace the less than 6 dollar part! Thanks partSelect!!!
Was this helpful?
Thank you for voting!
the lower drum support roller had been chewed to bits.
3 of 4 people found this instruction helpful.
  • Rodney from Mt. Jackson, VA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers
I pried open the top of the dryer, removed the 2 scrws holding the front cover of the dryer, un hooked the dryer drum buide belt, removed the dryer drum - all this just to get to the drum support roller. The bottom roller - the rubber on the wheel had been "chewed of". I can only guess because too much weight was placed in the dryer with wet clothes.
I removed the triangle shaped retaining clip, using the mini flat head screw-driver, slid the damaged roller off, replaced the new roller, and installed the new retaining clip. To install the new clip, I used a 1/2inch nut driver. I did the same to replace the upper drum support roller. The actual repair took less than 5 minutes, However, the prep time in dismanteling the dryer in order to get to the drumm rollers and puting the dryer back to gether consumed the bulk of my time.
Was this helpful?
Thank you for voting!
Lint trap was warped and would not stay in the opening.
3 of 4 people found this instruction helpful.
  • Carmella from THONOTOSASSA, FL
  • Very Easy
  • 15 - 30 mins
Easy for a 87 year old.I just snapped the cover to the filter basket and then inserted the whole basket into the
Was this helpful?
Thank you for voting!
The sound was like a cement mixer
3 of 4 people found this instruction helpful.
  • Russell from Apache Junction, AZ
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
When i finally got sick and tired of hearing it when she used the dryer. I popped the top flipped it up unscrewed the 2 screws holding the front panel of the body on, picked up on it and pulled it off the drum. I then reached back to the rear right corner and stretched the tentioner and pulled the belt off the motor pulley.Then I picked u p the belt and the drum and pulled it out of the dryer body. After seeing the drum support roller that is mounted on the base, and back of the left side I decided to go online and find this sight that had the drum support rollers as a set with the keepers and the push nut for the brace as a set for a really fair price. If your unit has a warranty "do not" take anything apart and do not order any pats until you check with your dealer. You do not want to void your warranty. I then pulled off the push nut and then i took the screw that held on the brace in front of the worn out drum roller, then pryed off the keeper and pull off the drum roller, took off the back keeper;inspect the shaft if it is not damaged ,(this one was not),then you wait until the parts arrive, yes your dryer will set in parts for about a week, but believe me in todays economy its worth "not having to buy a new dryer" at least for this small repair. When the parts arrive everything is pretty much in reverse of how you took it apart dont forget your cell phone is also a camera that can be a "memory enhancer" for when you get this far. Also be nice to your wife your going to need a little help putting it back together. Of course if she wants her dryer back she needs to help anyways. patience is a virtue and if you dont take your time and do this right it will be tested the drum and belt need to be fitted right and held up to get both the belt on the pulley and around the tentioner and get the front panel lined up on the front of the drum good luck and pass your knowledge on its getting to be a lost art.
Was this helpful?
Thank you for voting!
Dryer wouldn't start
3 of 4 people found this instruction helpful.
  • Claudia from NEWBURY PARK, CA
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Watched video, followed instructions. Works perfect.
Was this helpful?
Thank you for voting!
Door was popping open
3 of 4 people found this instruction helpful.
  • Harry from OTSEGO, MI
  • Very Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Watch the video before I received the part. Made it very simple to replace and which screws to take out.
Was this helpful?
Thank you for voting!
I recieved the kit the next day after ordering. It took about two seconds to do the repair
3 of 4 people found this instruction helpful.
  • WILFRED from NORTH HIGHLANDS, CA
  • Really Easy
  • Less than 15 mins
all that was required was to push the catch into the slot notools needed.
Was this helpful?
Thank you for voting!
All Instructions for the 110897
61 - 75 of 275