110840 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
No hot water and limited cold water during wash and rinse cycle
1 of 2 people
found this instruction helpful.
-
Les from GARNETT, KS
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
I followed the video instructions to the tee. Took more time to move the machine out and put back than to replace the inlet valve.
Was this helpful?
Thank you for voting!
did not have hot/warm water
1 of 2 people
found this instruction helpful.
-
Marcia from Simpsonville, SC
- Easy
- 15 - 30 mins
-
Screw drivers
I followed the instructions I found on your website. It made it very easy. Easier than if I had tried to do it the way I thought I had to remove the back of the washer. Going through the top panel made removing the bottom panel screws unnecessary.
The experts were correct, the instructions precise. Thank you
The experts were correct, the instructions precise. Thank you
Was this helpful?
Thank you for voting!
Cold water was trickling into wash tub
1 of 2 people
found this instruction helpful.
-
Brian from McKinney, TX
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Your video was helpful. I just followed the directions, replaced the valve, put it back together and celebrated spending $28 instead of the $100 deductible on my home warranty. If you're sure of the part you need, just do it.
Was this helpful?
Thank you for voting!
The hot water supply hose developed a bulge that was due to blow soon.
1 of 2 people
found this instruction helpful.
-
Victor from Hathway Pines, CA
- Really Easy
- 15 - 30 mins
-
Pliers
Shut off the hot water supply (pretty sharp eh?). Disconnected the hose from the hw supply and the at the connection to the washing machine. These had not been touched in at least 15 years and were somewhat tough to loosen but finally came ..... accessibility was a problem for the connection to the water supply as it was in a recessed wa
... Read more
ll box. Fortunately, we had some washers for the hose connections so the install was a snap. Hardest part of the whole job was moving the washing machine out from between the drier and the wash tub .... tight fit. Thanks for the quick service and to FED EX for their delivery. The delivery fellow was a real gentleman.
Read less
Was this helpful?
Thank you for voting!
washer would fill with water but not start
5 of 15 people
found this instruction helpful.
-
Edward from Nanuet, NY
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers
took part top of washer saw switch replaced it not to difficult it is always easier when you have new one to look at
Was this helpful?
Thank you for voting!
squealing noise, very little cold water to fill tub, hot water normal
1 of 3 people
found this instruction helpful.
-
richard from cleburne, TX
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
turn off hot and cold water faucets,unplug the power,pull washer out to gain access to rear cover, remove the top control panel screws,push back and lift off, disconnect hot and cold water hoses from inlet valve and remove enough screws from the back panel to remove the valve, disconnect the valve from the tub fill hose (mine had a spring
... Read more
type hose clamp) note the orientataion of the hot and cold hoses and the solenoid connectors for the hot and cold sides,(mine is stamped in the rear cover)reconnect and reassemble in reverse order and check for proper operation.
Read less
Was this helpful?
Thank you for voting!
Only hot water would be dispensed into the washing machine
1 of 3 people
found this instruction helpful.
-
Joselin from Port Saint Lucie, FL
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
took off the rear panel and removed the existing inlet valve and installed the new one. Replaced the rear panel and the machine work better than ever.
Was this helpful?
Thank you for voting!
Refill valve leaked continuosly.
1 of 3 people
found this instruction helpful.
-
Kenneth from Adrian, OR
- A Bit Difficult
- 1- 2 hours
-
Pliers, Socket set
Removed the hoses from the inlet valve. Removed screws that hold control panel in place . Removed control panel which exposed two clips that hold the top of the back panel. Removed the ground screw freeing the ground wire, removed the plastic loom which holds a bundle of wires. I next removed the plastic plate that protects the fil
... Read more
l valve from splashed water. Removed the screw that holds the valve in place, then removed the wires and the fill hose. Reversed steps to put back together.
Read less
Was this helpful?
Thank you for voting!
The water inlet valve was defective
1 of 3 people
found this instruction helpful.
-
Kent from San Diego, CA
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
First I turned off the water to the washer and then removed the hot/cold water hoses going to the washer, unscrewed the water hoses from the washer, and cleaned the wire screens located immediately inside the inlet water valve. This did not solve the problem. Second, I loosened the hex head screws on the back panel of the washer. This
... Read more
allowed me access to the valve. I tested the valve solenoids with my ohm/volt meter and all checked out OK (but this did not make sense). Third, I surfed the web to find out if the symtoms of the washer's problem were the same as experienced by other people. I found several reports of the same symptoms, all which were solved by replacing the water inlet valve. This conformed my original diagnosis although the valve tested as OK. Fourth, I ordered the part from PartSelect, and removed the hose clamp and two mounting screws holding the old valve to the back panel of the washer and removed the old valves. Last, when the new valve arrived, I assembled the new backing plate to the new valve, attached it to the washer's back panel, attached the water hoses to the valve after fitting new rubber seals to the inside of the hoses, and reattached the washer back panel. The washer is working perfectly again.
Read less
Was this helpful?
Thank you for voting!
My washing machine overflowed and flooded the basement
1 of 3 people
found this instruction helpful.
-
Laura from Sterling, CT
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers, Wrench (Adjustable)
First, I unplugged it and disconnected the water hoses (the water has been off to it for days). Then, I tried taking off the back of the washing machine. This didn't work, and I actually ended up googling instructions and found pretty detailed, illustrated instructions at Popular Mechanics.
You need to unscrew the front panel that ... Read more contains all of the controls first, flip it up, and unhook it from the back of the washer (via an electronics clip and 2 metal clips). The outer cover can then be taken off. I recommend undoing the internal hose next -- I used adjustable pliers to squeeze the connecter and loosen the hose. Then, unscrew the water inlet valve and take it off.
Putting everything back together literally just means reversing the instructions.
My washing machine is on a raise service, and I still haven't gotten the outer frame completely back in place correctly, but it's not touching anything or creating any problems. It's really only to safeguard parts anyways, so no worries if it's not perfect -- at least it works now!
You need to unscrew the front panel that ... Read more contains all of the controls first, flip it up, and unhook it from the back of the washer (via an electronics clip and 2 metal clips). The outer cover can then be taken off. I recommend undoing the internal hose next -- I used adjustable pliers to squeeze the connecter and loosen the hose. Then, unscrew the water inlet valve and take it off.
Putting everything back together literally just means reversing the instructions.
My washing machine is on a raise service, and I still haven't gotten the outer frame completely back in place correctly, but it's not touching anything or creating any problems. It's really only to safeguard parts anyways, so no worries if it's not perfect -- at least it works now!
Read less
Was this helpful?
Thank you for voting!
There was no cold water entering the machine.
0 of 1 people
found this instruction helpful.
-
Laura from Vienna, VA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers, Wrench (Adjustable)
I replaced the water inlet valve. First I watched a YouTube video on the repair; surprised to learn that you take the machine apart from the front, not the back.A few tips; pull the washer all the way out first; have extra tools in case you have the same problem as I did that the flathead screws holding the old valve on the back were too
... Read more
tight and had a shallow slot; it took several wrenches and pliers to get them turning. Do NOT forget to hook the internal hose back to the valve before reassembling the machine;and pay close attention to how the housing of the washer fits onto the frame, so that you can more easily put it back together. It would be helpful to have a second person for that step. All said, it was pretty easy to replace the part and I probably saved $200 and didn't have to sit around for a repairman.
Read less
Was this helpful?
Thank you for voting!
cold water solenoid would not open much
0 of 1 people
found this instruction helpful.
-
Dave from Kingsport, TN
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
Unplugged the washer and pulled out from wall as far as hoses would permit. Removed and drained both supply hoses. Removed drain hose and drained. Any water left in the tub will drain here so it's best to make sure it's drained prior to repair. Used pliers to hold the hose clamp and removed. Took screws out of drain hose interface pl
... Read more
ate and pulled out far enough to disconnect it from the internal hose.
Removed the two front screws of the control console. removed the two top hinge screws on the back. Removed four screws at the bottom of the rear access panel. Had to lift unclip several clamps holding the level hose in the control console and a cable connector. Unclipped various clips in the back panel to free it from wire bundle and such. Lifted the back panel up off of the clips located at the rear base of the control panel.
Removed two screws to free the solenoid assembly from the back panel. Unplugged the connectors to the original solenoid assembly. Disconnected the internal hose from it. Installed screw and plate supplied with the replacement solenoid to configure it with the same orientation as the original. Connected the internal hose and electrical connectors. Reassembled the back in reverse order as diassembled.
Removed the two front screws of the control console. removed the two top hinge screws on the back. Removed four screws at the bottom of the rear access panel. Had to lift unclip several clamps holding the level hose in the control console and a cable connector. Unclipped various clips in the back panel to free it from wire bundle and such. Lifted the back panel up off of the clips located at the rear base of the control panel.
Removed two screws to free the solenoid assembly from the back panel. Unplugged the connectors to the original solenoid assembly. Disconnected the internal hose from it. Installed screw and plate supplied with the replacement solenoid to configure it with the same orientation as the original. Connected the internal hose and electrical connectors. Reassembled the back in reverse order as diassembled.
Read less
Was this helpful?
Thank you for voting!
Cold water flow very slow
0 of 1 people
found this instruction helpful.
-
Steve from Scottsburg, IN
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Our washer's cold water flow became very slow. We were living with just hot water washing for about a month. I had used PartSelect in past and have always been very satisfied with the outcome. So, I went on the site and within a couple of minutes of navigating, had the part (water inlet valve with mounting plate) on order.
I ... Read more watched the repair video on the water valve ordering page. My installation went pretty much to this procedure, with one exception, I had to use the mounting plate, which I don't think was covered in the video. You have to read and follow the instruction sheet that comes with the part. Therefore, my installation instructions are to a) watch the video, b) get together all the recommended tools described in the video, c) be prepared to use the mounting plate (which uses the same 1/4 nutdriver the video says is needed).
I did the complete valve replacement and had the washer back in place in just at 30 minutes, the tight closet quarters added a bit to this time I'm sure. Working in a basement or open utility room would have been a little easier and quicker. My shortfall though is, I should have done the hose connection check (turning the supply valves back on) before making the move back into the washer space, as once I performed what I thought was my last step, turning on the supply valves, I heard a water leak. This was resolved with another 10 minutes worth of moving the washer back out, disconnecting the hose, removing the rust debris which apparently caused the leak, reconnecting the hose, and this time, checking for leaks BEFORE moving the appliance back into place. I think the time estimate of 30 minutes is good for individuals with moderate experience in appliance repair, and probably good for the novice in conjunction with the video.
I ... Read more watched the repair video on the water valve ordering page. My installation went pretty much to this procedure, with one exception, I had to use the mounting plate, which I don't think was covered in the video. You have to read and follow the instruction sheet that comes with the part. Therefore, my installation instructions are to a) watch the video, b) get together all the recommended tools described in the video, c) be prepared to use the mounting plate (which uses the same 1/4 nutdriver the video says is needed).
I did the complete valve replacement and had the washer back in place in just at 30 minutes, the tight closet quarters added a bit to this time I'm sure. Working in a basement or open utility room would have been a little easier and quicker. My shortfall though is, I should have done the hose connection check (turning the supply valves back on) before making the move back into the washer space, as once I performed what I thought was my last step, turning on the supply valves, I heard a water leak. This was resolved with another 10 minutes worth of moving the washer back out, disconnecting the hose, removing the rust debris which apparently caused the leak, reconnecting the hose, and this time, checking for leaks BEFORE moving the appliance back into place. I think the time estimate of 30 minutes is good for individuals with moderate experience in appliance repair, and probably good for the novice in conjunction with the video.
Read less
Was this helpful?
Thank you for voting!
water inlet valve not let water in washer
0 of 1 people
found this instruction helpful.
-
Ronald from prince george, VA
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Socket set
removed the two screw that hold the inlet valve take hose of .the first was takeing the back of than the hoses from back hose on bottom of machine.
Was this helpful?
Thank you for voting!
Cold water inlet valve went out
0 of 1 people
found this instruction helpful.
-
Sandra from Ash Flat, AR
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Wrench (Adjustable), Wrench set
My son did the repair. Thank God for Sons who know how to repair things. Worst thing was figuring out how to get the back off, top where dials are had to come off too. the rest was easy according to him..
Was this helpful?
Thank you for voting!