110840 Kenmore Washer - Instructions

All Instructions for the 110840
76 - 90 of 221

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
water valve neede replaced
2 of 4 people found this instruction helpful.
  • Timothy from summerfield, FL
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set
The valve was easy to change, but we as homeowners should change the hot and cold hoses just like they say you should every 5 years. The hoses grew to the water valve and it was almost a disaster. After cutting the end with a dremmel and clamping visegrips on it I finally got it loose. After that it went smooth. Thanks for getting me the part so fast.
Was this helpful?
Thank you for voting!
Washer wouldn't fill up with hot water
1 person found this instruction helpful.
  • Paul from Winston-Salem, NC
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable)
I just followed the instructions found on this website. It covered everything you need to know. I have just one thing to add though. Look over everything first and formulate a game plan. Keep all screws etc. and put them in a plastic bag so you don't lose them. You might try using a heavy hammer to force the clips holding the back panel t o the top of the machine back in place. One more thing; use a piece of wood to set the back panel on while you replace the intake valve.
Was this helpful?
Thank you for voting!
Cold Water valve would not shut off
1 person found this instruction helpful.
  • John from Fair oaks, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Removed two clips on back panel holding control panel.Removed end plates on control panel. removed two front screws holding control panel. removed wiring harnesses noting location. Set control panel aside. Removed two large clips holding rear panel to washer cabinet. Pulled washer cabinet from the front away from the rear panel and tube. Removed two screws holding water inlet valve. Removed water inlet hose from inlet valve using channel lock pliers. Installed new water inlet valve using supplied mounting bracket. Reassembled washer in reverse order.
Was this helpful?
Thank you for voting!
Dripping When Washer is Off
1 person found this instruction helpful.
  • Herbert from Daly City, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers
This should have been done under 30 minutes but when you don't have a repair manual, you have to do some guessing. I have to remove the back panel. On only thing that was hard was unspringing the two flat springs. After I got the panel off, the rest was easy and the dripping stopped. Oh, there is a screen where the hose connects to t he inlet valve. If you can clean the screen often, you can continue to get a good water flow.
Was this helpful?
Thank you for voting!
The switch was not working so got a new switch
3 of 7 people found this instruction helpful.
  • satyavenkata from Bentonville, AR
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Unfortunately after i replaced the new switch the drier worked well. After it stopped for the 2nd time we wanted to put a load and start the swit lost contact. It was not working.It lost the contact with the circuit. No clicking sound the drier not functional. I guess need a new switch?
Was this helpful?
Thank you for voting!
washer would partially fill itself when not in use
1 person found this instruction helpful.
  • Adrian L from Houston, TX
  • A Bit Difficult
  • 30 - 60 mins
  • Wrench (Adjustable)
I had to call in to find the correct part because the online recommended part looked very different, and the one found using the model number had no photo, so I was VERY leary of ordering. The service rep said that Kenmore products did not always show up correctly and he gave me the part number needed and there was a photo. The part was not exactly the same, but looked very similar and it was more than 50% less than the original recommended part and part with no photo. I thought that the problem finding Kenmore parts was odd since Kenmore is like number one, right? Part took 3 days to arrive, which I thought was great. Turned off power and water. Removed water hoses. Removed three screws from the back of the top (front loader). Removed the top. Removed a screw holding on the water inlet valve from the outside of the unit through the back cover which required a star driver. Unattached the 4 electrical leads. Unattached the outlet water hose (held on with a squeeze type metal clamp -not sure of the exact name for these). The problem that I had was that the water outlet hose bib attachment was slightly larger than the old one, so the hose would go back on, but the clamp was too small so I cusses a lot before figuring out the problem. I had to go and purchase a new larger clamp. After that, I simply attached the electrical connections and put the outlet back on. One other small problem was that the place where the screw through the back cover was originally attached no longer lined up with the new valve. The plastic piece was shorter than the old one so the screw hole did not line up with the hole in the back panel. The screw isn't really necessary. Overall, replacing the part was easy and I was pleased with the process.
Was this helpful?
Thank you for voting!
washer continued to spin when you raised the lid not shutting off
1 of 2 people found this instruction helpful.
  • Daniel from TRENTON, NJ
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Your web site is amazing Ive enjoyed watching your videos,this is a really great way to see what it takes to repair your washer very informative. Steve was a good teacher for me I just followed along as he explained each step and my washer came apart just like he said. I removed the two front console screws and pulled slightly forward and lifted console up and tilted it back where it was out of the way. next I was able to lift cabinet up from the back and remove it from the frame and lay cabinet on the floor on top of a rug I had to protect the finish on cabinet . Now I had access to the lid switch and simply removed the two screws in the cabinet and the old switch. I connected the two wire connections to the new switch (no)normally open connection, used same actuator the instructions say to do this because the one that comes with the new switch won't fit so use the old one. on my washer there's a cover that fits under this switch and It took me a little longer to get the screws to line up so they fit through the switch and into the cover but It worked fine. Now all I had to do was reinstall the cabinet just like Steve did on the video my only problem with this was seeing where the tabs in the frame were located so that the slots in the cabinet would fit over top of frame tabs I used a flash light in one hand and lowered the cabinet down I held the light on the frame tabs and the slots in cabinet fit right in then lowered cabinet to the rear frame tabs where i just had to push slightly on the sides of cabinet and it fit right in.Next i pushed the back panel in place and on the top of washer just like in video reinstalled both spring clip clamps and the console and reinstalled the two screws. I plugged in the washer put drain hose back in drain pushed washer back in place turned it on working great now ! Thank You so much for your help Dan.
Was this helpful?
Thank you for voting!
Washer exhibited LOW cold water flow and dripping when off.
1 of 2 people found this instruction helpful.
  • Cory from Alexandria, VA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
The repair went great. The video shown on the partselect site saved me a huge amount of time disassembling the cabinet to access the malfunctioning part. The most difficult part of the repair was replacing the cabinet on the unit after the part swap and getting it straight. Luckily 2 attempts was enough. I recommend trying this repair yourself and saving a bunch of $$.
Was this helpful?
Thank you for voting!
Cold water input into the washing machine was very slow.
1 of 2 people found this instruction helpful.
  • James R from Birmingham, AL
  • Difficult
  • More than 2 hours
  • Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
The hot water hose was frozen to the hot water bibb and it took me a while to cut it loose with my Dremel tool. Removed the cabinet and replaced the water inlet valve easily, then hooked up new hot and cold water hoses. Reinstalling the cabinet was a little tricky getting it lined up correctly. Checked for leaks then tested the washing machine and it ran great with the water filling the machine much faster with the new Water Inlet Valve. I will definitely replace the washing machine hot and cold water hoses every 5 years from now on.
Was this helpful?
Thank you for voting!
Lid switch failed, dryer stopped working
1 of 2 people found this instruction helpful.
  • Rick from BETHESDA, MD
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Order replacement lid switch, installed it, good to go. The installation video and instructions with the replacement part were very helpful.
Was this helpful?
Thank you for voting!
No hot water flow, cold water flow very slow
1 of 2 people found this instruction helpful.
  • Steve from Minneapolis, MN
  • Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
It is sometimes tricky to figure out which screws and panels to remove to get to the parts you want to fix. Older Whirlpools used to have a lift up top that would allow access. This one required the back to come off (or at least partially off).

First, pull out the washer for access. Turn off water to the machine, and unplug the electrical cord. Remove the drain hose using a large pliers to pinch the clamp and then pull the hose off. Remove water lines at the back of washer, again with a large pliers (if needed). Remove two screws at the bottom of back panel. Remove two screws at the top corners of back panel that hold some sort of plastic hinge piece to the control housing. Remove two screws on either end of the bottom front of the control housing on top of the machine. The back can now be lifted free (with some effort) from the sheet metal tabs that hold the bottom of the back in place. Reach in the bottom side with the pliers and disconnect the large drain line clamp so you have more room to swing the back out. There also might be a little plastic thingy to twist out of a slot in the back (maybe a vibration damper?) You will see the water inlet valve just inside the back on the side. The inlet hose connections are actually a part of the inlet valve. It is now possible to reach in from the side and disconnect the small water feed line from the inlet valve with a pliers, and disconnect the electrical plugs from the valve. Remove the two screws holding the valve to the back and remove the valve.

Reassembly is actually easier than removal. Don't forget to replace the water hose washers or they will probably leak. If the hoses look bad, just buy a new set. They can be had quite cheap.

Good luck and prepare to be proud of how well your "new" washer now works and how much money you saved!

p.s. PartSelect Rocks!
Was this helpful?
Thank you for voting!
Water would not shut off causing the washing machine to overflow.
1 of 2 people found this instruction helpful.
  • Brent from Donnelly, ID
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
The repair went smoothly once I found detailed instructions including pictures on the web. The inlet valve is mounted on the back panel of the machine. To get access to the valve you need to remove the front/side cabinet. This was done by removing the two plastic moldings on the ends of the control panel, swing the control panel back, removing two screws, then tilting the front/side cabinet forward. The inlet valve was held in place by one screw and attached to the washer with a hose clamp. Reverse the process and the job was done.
Was this helpful?
Thank you for voting!
Water Would Not Shut Off
1 of 2 people found this instruction helpful.
  • FLOYD from MOUNT VERNON, KY
  • Easy
  • 15 - 30 mins
  • Screw drivers
Just took screws on top panel holding the gauges pop the spring like braces holding the body of machine to back panel removed water valve one screw unhooked wireing than replaced new valve in reverse order.
Was this helpful?
Thank you for voting!
washer was over flowing
1 of 2 people found this instruction helpful.
  • richard from grants pass, OR
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Pliers
unlike the other's that said to take the top control panel off, i turned the machine up side down and was able to reach the valve from the bottom. it does require a good reach in but an average length arm will make it. just take the rubber hose loose from the valve with a pair of pliers, or hose clamp pliers if you are so blessed to have them, then pull the hose loose from the valve, then take the two electrical conectors off noting wich one goes with each side, then a nut driver should remove the valve without difficulty. installing new valve should be the reverse. i was up in running in minutes. it took longer to undo the hoses and reattach the hoses than to replace the valve.
Was this helpful?
Thank you for voting!
orginal water inlet failed due to age, easy fix !
1 of 2 people found this instruction helpful.
  • Kenneth from RIVER EDGE, NJ
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Removed top control panel, removed inlet mount hardware, removed both electrical connectors, removed filler hose, Installed new inlet valve in reverse order. Works fine !
Was this helpful?
Thank you for voting!
All Instructions for the 110840
76 - 90 of 221