110840 Kenmore Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The agitator had stopped working
1 person
found this instruction helpful.
-
Jack from Matthews, NC
- Easy
- 15 - 30 mins
-
Socket set
We got the parts, watched your video a couple of times and then began the repair. It went well with one exception. None of my socket extensions were long enough to work well. The required length might be added to the video and the printed installation instructions. Also it would have nice to have been able to order a small tube of the rec
... Read more
ommended lubricant. Overall I was very pleased. Jack
Read less
Was this helpful?
Thank you for voting!
Water would not stop filling out the tube.
1 person
found this instruction helpful.
-
GEORGE from WEST HILLS, CA
- Very Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
1- Remove power connection, remove water connections. 2- Remove the top controller box and free it from its hinges. 3- Loosen the back cover to get access to water valve assembly. 4- Remove hose clamp connected to inlet water valve. 5- Remove the old water valve which is secured with 1/4" screw. 5- For installation perform step 5 to 1 and
... Read more
then test your Installation.
Read less
Was this helpful?
Thank you for voting!
Broken lid switch actuator
2 of 4 people
found this instruction helpful.
-
Andrew from WEST WARWICK, RI
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers
Ordered the correct part, watched a YouTube video.
Was this helpful?
Thank you for voting!
Slow running cold water to washer.
1 person
found this instruction helpful.
-
Phillip from EATONTON, GA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
1- Unplugged washer. 2- Turned off water supply to hoses hot and cold. (marked hoses H C) 3- Unscrewed hoses to washer. 4-Used phillips head screw driver to take out screws(2) at corners of washer. 5- Slid top of washer forward and lifted top off. 6- Took out retaining clips on each side of washer. 7- Slid frame of washer outward exposin
... Read more
g rear panel of washer for access to water inlet valve. 8- Used 1/4" drive to take out screw to inlet valve. 9- Removed inlet valve, unplugged the two connectors and removed clamp from hose to valve. 10- Replaced new inlet valve and reversed the process to assemble washer back together. Total time for repair, about 45 minutes. I now have full running cold water to washer. Thanks guys for the video you provided. Would purchase again if needed. Thanks again!!! Water Inlet Valve with Mounting Bracket Part Number: PS334646
Read less
Was this helpful?
Thank you for voting!
Water would not stop running
2 of 4 people
found this instruction helpful.
-
Judy from BERNVILLE, PA
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Wrench (Adjustable)
Followed by installation on line
Was this helpful?
Thank you for voting!
Inlet Water would not stop running.
1 person
found this instruction helpful.
-
Paulette from FORT WORTH, TX
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Unplugged the power while the washer was running, and the water kept on running. The water inlet valve was stuck open. I removed the inlet valve and you cold blow air thru it, it should be closed with no power applied.Ordered replacement from this site it was a perfect fit. As far as the removal and installation procedure, just follow the
... Read more
video as presented on this site. Good Look.
Read less
Was this helpful?
Thank you for voting!
Would not drain
1 person
found this instruction helpful.
-
Robert from SANDWICH, IL
- Really Easy
- 15 - 30 mins
-
Wrench set
Replaced lid switch, but problem still continued.
Was this helpful?
Thank you for voting!
No problems
1 person
found this instruction helpful.
-
Wayne from ZEPHYRHILLS, FL
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
I got a few hints from YouTube (how to remove the washing machine casing) and rest was very simple
Was this helpful?
Thank you for voting!
water inlet valve bad
1 person
found this instruction helpful.
-
linville from lily, KY
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
received valve as ordered a simple installation. everything went well.home owner can do this repair
Was this helpful?
Thank you for voting!
Won't pump out the water
1 person
found this instruction helpful.
-
Victor from NORFOLK, VA
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Order the part and put the new part on and put the washing machine cabinet back on and check the washer for the water filled up and then it's starting to go on the spin cycles.
Was this helpful?
Thank you for voting!
cold water wasn't shutting off between fills on washer
1 person
found this instruction helpful.
-
Daniel from Delavan, WI
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Wrench (Adjustable)
Turn off water, unplug machine
Disconnect water lines to the valve
Unscrewed the clear plastic tabs on the top of the machine, then pryed the back away from the top white part.
Two gold clips can be popped out with a long flat head screw driver.
Pulled the back away from the machine enough to disconnect the wires from ... Read more the valve. Unscrew the screw(s) from the valves.
Old valves out, new valves in. Plug in the wires, screw in the screws.
Then, to get the gold tabs back in place.....i called NASA.
just kidding. They're tough!
I slipped one into the back and held it in place with my thumb. Then I lined the piece up with the slot inside the machine. Then, i pryed the top white part away as I pushed them together. Stuck a long handle screwdriver down in and pushed REALLY hard on the gold tab to get it to snap into place. Everything is really tight, so you might have to try it a few times.....i left some blood behind.
repeat for the other side, snap in the clear tabs, hook up the water lines, plugged it in......
Then I sat back and listened to my wife praise me for fixing her machine!
Disconnect water lines to the valve
Unscrewed the clear plastic tabs on the top of the machine, then pryed the back away from the top white part.
Two gold clips can be popped out with a long flat head screw driver.
Pulled the back away from the machine enough to disconnect the wires from ... Read more the valve. Unscrew the screw(s) from the valves.
Old valves out, new valves in. Plug in the wires, screw in the screws.
Then, to get the gold tabs back in place.....i called NASA.
just kidding. They're tough!
I slipped one into the back and held it in place with my thumb. Then I lined the piece up with the slot inside the machine. Then, i pryed the top white part away as I pushed them together. Stuck a long handle screwdriver down in and pushed REALLY hard on the gold tab to get it to snap into place. Everything is really tight, so you might have to try it a few times.....i left some blood behind.
repeat for the other side, snap in the clear tabs, hook up the water lines, plugged it in......
Then I sat back and listened to my wife praise me for fixing her machine!
Read less
Was this helpful?
Thank you for voting!
Dryer would not start, timer had no power to it.
1 person
found this instruction helpful.
-
Billy from NEW BERN, NC
- Easy
- 30 - 60 mins
-
Screw drivers
Raise the top off of the dryer with a flat blade screwdriver in each front corner of the dryer. Disconnect power to the dryer. Remove old switch and install new switch. Test door and proper operation of dryer.
Was this helpful?
Thank you for voting!
spin cycle did not activate
2 of 4 people
found this instruction helpful.
-
Enrique from Miami Shores, FL
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
Replaced hinge switch. Still no spin cycle. Noticed hinge bearing cracked & if hinge forced into switch, spin activated. Ordered new hinge bearings.Spin cycle still didn't engage. On further examination, observed that hinge was bent. Straightened hinge & worked like a charm. Didn't really need new switch or bearings. NOTE : Avoid having w
... Read more
asher door bang shut.Took longer than expected, but each procedure was simple.
Read less
Was this helpful?
Thank you for voting!
When washer was in cold water rinse cycle, loud squealing noise.
1 person
found this instruction helpful.
-
James from LEXINGTON, KY
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers
unplug unit first Took water & drain hose loose, used two wheel dolly, took washer out on patio. Removed water hose. Removed two screws # 49 an laid back control unit then Removed 2 #6 Clips Top of unit, then pried back unit cover out enough to remove Water valve after removing #4 screw that holds unit to back panel ,removed hose clam
... Read more
p #21 an electric connections, install new water valve and put back together..DO NOT TAKE BOTTOM SCREWS FROM BACK PANEL, if so the bottom will drop.. Intake cold water valve was half stopped up. Also new water lines.
Read less
Was this helpful?
Thank you for voting!
Water would not stop coming in when ran all the time
1 person
found this instruction helpful.
-
Norwood from Peachbottom, PA
- Easy
- 1- 2 hours
-
Pliers, Screw drivers
unscrewed the back removd thr two screws for the element unhooked the hose to machiine unpluged the electric to element and than replaced new element and plugged electric to element and hooked back the hose and replaced screws too the back and replaced back an screws
titled wash machine up hooked hoses for the water and plugged el ... Read more ectric and put drain hose back to drain done
titled wash machine up hooked hoses for the water and plugged el ... Read more ectric and put drain hose back to drain done
Read less
Was this helpful?
Thank you for voting!