110781 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
gas dryer would fire, but shut down before getting warm enough to dry clothes
7 of 7 people
found this instruction helpful.
-
Glenn from Ossian, IN
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set, Wrench set
Removed lower front cover of dryer, located coils, removed old coils by disconnecting the wires and removing the hold down bracket screws. Pulled the old coils out replaced them with the new coils by aligning the index pins on the coils with the holes in the bracket then reattached the bracket and plugged the wires into the new coils. The
... Read more
n closed the cover on the front of the dryer. Dryer now ignites and stays on to heat up and dry clothes.
Read less
Was this helpful?
Thank you for voting!
Original lint filter too warped to be used
7 of 7 people
found this instruction helpful.
-
David from RENO, NV
- Very Easy
- Less than 15 mins
I took out the old filter, put it into the recycle bin and dropped in the new filter. I was done.
Was this helpful?
Thank you for voting!
Dryer not Drying
8 of 10 people
found this instruction helpful.
-
Manuel from Jurupa Valley, CA
- Easy
- 30 - 60 mins
-
Screw drivers
Replaced both Coils. Purchased M Series coils much less expensive buying coils together instead of seperately. Problem solved.
Was this helpful?
Thank you for voting!
Lost bearing on dryer motor
9 of 13 people
found this instruction helpful.
-
John from Wilmington, OH
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
I looked at the parts breakdown to see how it cam apart.
I tore the dryer down,
1. removed the door
2. openned the top
3. removed front panel
4. removed fron bulkhead
5. removed belt and drum
6. removed back cover
7. removed the ductwork
8. removed the fan (this is ... Read more the hardest part, it is very tight on the motor with left hand threads, there are flats on the (inside of the dryer)fan where the motor shaft goes into the fan for a wrench and you can put a socket on the front pulley on the motor. I ended up just knocking the center out of the fan and replacing it.
9. removed the motor and cleaned the entire unit
10. reinstalled everything in reverse order. Note:I went ahead and replaced the idler pulley and the rear wheels that support the drum, and put a new belt in (just about
everything that could fail) I spent about $200 to keep a $1200 dryer in service at least another 7 years.
I tore the dryer down,
1. removed the door
2. openned the top
3. removed front panel
4. removed fron bulkhead
5. removed belt and drum
6. removed back cover
7. removed the ductwork
8. removed the fan (this is ... Read more the hardest part, it is very tight on the motor with left hand threads, there are flats on the (inside of the dryer)fan where the motor shaft goes into the fan for a wrench and you can put a socket on the front pulley on the motor. I ended up just knocking the center out of the fan and replacing it.
9. removed the motor and cleaned the entire unit
10. reinstalled everything in reverse order. Note:I went ahead and replaced the idler pulley and the rear wheels that support the drum, and put a new belt in (just about
everything that could fail) I spent about $200 to keep a $1200 dryer in service at least another 7 years.
Read less
Was this helpful?
Thank you for voting!
No heat
9 of 13 people
found this instruction helpful.
-
Philip from La Palma, CA
- Really Easy
- 1- 2 hours
-
Nutdriver, Screw drivers, Wrench set
Took everything apart, replaced the igniter flint, and still didn't get heat. Then found out the thermal sensor wasn't running a electrical current through it with voltmeter and just replaced that, now it we have heat again!
Was this helpful?
Thank you for voting!
the glow ignitor would not cycle on
7 of 8 people
found this instruction helpful.
-
Georgio from Oradell, NJ
- Easy
- Less than 15 mins
-
Nutdriver, Pliers
I had an issue where I was not getting any power to my ignitor. After replacing the ignitor with a fresh one, the problem persisted. Next, I went hunting all the fuses and therrmostats for continuity. All seemed fine. So finally I decided to jump the flame sensor which is located on the outside of the flame tube. WHALLA! It ignited the g
... Read more
low plug. So with one 1/4"" nut driver I removed the single bolt from the unit, then I used a pliers to remove the two wires from the old unit. I replaced the sensor with Tue new unit and all was well. It took less than 5 min once I diagnosed the problem.
Read less
Was this helpful?
Thank you for voting!
No Heat After 10 Minutes
7 of 8 people
found this instruction helpful.
-
lawrence from GROTON, VT
- Really Easy
- 15 - 30 mins
-
Nutdriver, Wrench set
Shut off gas removed gas valve. Removed the coil retainer and installed the new coils. Reinstalled valve and checked. Found dryer worked fine.
Was this helpful?
Thank you for voting!
no heat was being produced
9 of 14 people
found this instruction helpful.
-
reinaldo from guttenberg, NJ
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Remove back panel n u can see the sensor and easy to replace thanks to the print out i was provided love this website
Was this helpful?
Thank you for voting!
Broken door latch
6 of 6 people
found this instruction helpful.
-
William from ROCK ISLAND, IL
- Very Easy
- Less than 15 mins
-
Pliers
Followed video instructions using flat scraper & pliers (easy).Tried to remove "SPARE" latch on other side of door. Even removed door myself (Easy).Tried for (45) minutes without success. Ordered part @ 11:30 pm. Replaced door easily by myself by leaving bottom screw for each hinge in place & replaced broken latch. Received new latch in
... Read more
(5) days. Removed broken latch without tools & replaced new latch in (15) seconds. Need help from any "Ladies" who can remove second latch so it is available for next replacement. This "Engineer" was too lazy to remove the screws around the door because he was going to "Follow the Video". Overall it was an "Easy Fix". Keep the 'Videos"coming.
Read less
Was this helpful?
Thank you for voting!
Door catch will no longer secure the door close
6 of 6 people
found this instruction helpful.
-
Gregory from Carlsbad, CA
- Easy
- Less than 15 mins
-
Pliers, Screw drivers
Pliers and screw driver to pop out the old door catch and pop in the new one. Saved $69.95 service charge for a tech to come to the home.
Was this helpful?
Thank you for voting!
Loud Noise While Drying
7 of 9 people
found this instruction helpful.
-
John from Metamora, OH
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
Followed simple instructions to replace two pulleys and belt. The Virtual Repairman helped me identify the cause in minutes. Took another 5 minutes to place the order and the part arrived two days later. Saved $125 at least. Thank you!
john
john
Was this helpful?
Thank you for voting!
No Heat
7 of 9 people
found this instruction helpful.
-
Ken from Bixby, OK
- Easy
- More than 2 hours
-
Nutdriver, Screw drivers, Socket set
Thermal fuse was blown so I replaced it. Still no heat. Hi-Limit thermostat and Cycling Thermo. had continuity as did flame sensor. Igniter tested 66ohms. I placed a wire jumper across the Hi-Limit and the igniter glowed, solenoids opened and gas came on. I orderd the Hi-Limit and since both "overheating" limiters were defective I de
... Read more
cided to order the cycling thermo just in case. The Hi-Limit was received in 2 days but the Cycling Thermo was backordered. In the meantime my wife got antsy so I went ahead and installed the Hi-Limit and put her back in service... ...for one load. I wasn't certain if I had fried the "limiters" again but since they had continuity and I could measure continuity all the way to the Igniter I decided that it HAD to be the cause. I ignored the flame sensor since it never came into play without the igniter glowing... The igniter arrived and measured 56ohms. Hmmm... After installing the problem was solved. Word of advice: If the thermal fuse is blown and even if all else in the circuit SEEMS ok, go ahead and order the Fuse, Hi-Limit and Cycling Thermos, and the Igniter. It will take you about 30 minutes to install and you'll reduce your out-of-service time! Good luck!
Read less
Was this helpful?
Thank you for voting!
Idler pulley squeaking very badly
6 of 6 people
found this instruction helpful.
-
Andy from DAGGETT, MI
- Really Easy
- 30 - 60 mins
-
Socket set
Took back panel of dryer off completely disconnected the drive belt to drum of dryer took off old idler pulley reinstall the new pulley and belt works like a brand new dryer
Was this helpful?
Thank you for voting!
Dryer making a rumbling sound
8 of 13 people
found this instruction helpful.
-
Michael from Jacksonville, FL
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Purchased the dryer maintenqance repair kit. Very simple to do. Easy to follow instructions. Took less than an hour. Everything I needed was in th kit. Did not have to run to home depot for anything.
Was this helpful?
Thank you for voting!
Convert New Dryer to Propane from Natural Gas
9 of 16 people
found this instruction helpful.
-
Teri from Bakersfield, CA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
1.Unplugged the connections to dryer door
2. Removed dryer door, front cabinet,popped off the drum belt (this is done by feel),unplugged the drum from cabinet, removed drum, all to get to the gas element inside at the bottom of dryer.
3. Unplugged the connection to the element, then removed unit to get to the burner parts.
... Read more >4. Replaced the natural gas burner element with the LP gas element.
5. Re assembled dryer and tested.
*Note: Actually my son did the work while I read the very easy to follow directions. Since neither of us has disassembled a dryer before, the thought of taking a brand new dryer all apart was more daunting than the actual task.
2. Removed dryer door, front cabinet,popped off the drum belt (this is done by feel),unplugged the drum from cabinet, removed drum, all to get to the gas element inside at the bottom of dryer.
3. Unplugged the connection to the element, then removed unit to get to the burner parts.
... Read more >4. Replaced the natural gas burner element with the LP gas element.
5. Re assembled dryer and tested.
*Note: Actually my son did the work while I read the very easy to follow directions. Since neither of us has disassembled a dryer before, the thought of taking a brand new dryer all apart was more daunting than the actual task.
Read less
Was this helpful?
Thank you for voting!