110781 Kenmore Dryer - Instructions

All Instructions for the 110781
121 - 135 of 573

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Drum support roller making very loud noise
5 of 5 people found this instruction helpful.
  • William from TROY, AL
  • Really Easy
  • 1- 2 hours
  • Screw drivers, Socket set
had to take front off of Dryer then was able to replace drum roller
Was this helpful?
Thank you for voting!
Very noisy from support wheels
7 of 12 people found this instruction helpful.
  • Steven from WICHITA, KS
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Socket set
Changed all 4 drum support wheels and belt tension arm
Was this helpful?
Thank you for voting!
Dryer would not heat up properly. It would heat initially but once the heat was off it would not come on again.
5 of 6 people found this instruction helpful.
  • Joseph from Chicago, IL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
I followed the advice posted by other customers. I took the front off the dryer, put the door back in place and ran a cycle. I could see that the igniter was heating properly, but no gas was flowing. Based on what I read I concluded that it was a problem with one of the gas valve coils. It was relatively inexpensive to replace both (a nd the dry is 10 years old), so I didn't go to the trouble of determining the bad one. I replaced them both. Obviously I unplugged the dryer (no need to turn off gas). There were 2 screws that held the bracket in place which holds the coils. I disconnected the coils, removed the bracket screws, replaced the coils, reattached the bracket screws and reconnected the coils. I then reattached the front plate to the dryer. It was very easy and took about 20 minutes and I had never worked on a dryer before.
Was this helpful?
Thank you for voting!
Dryer made squeaking noise, then more of a rumbling noise.
5 of 6 people found this instruction helpful.
  • JAMES from NORTH OLMSTED, OH
  • A Bit Difficult
  • 1- 2 hours
  • Pliers, Socket set, Wrench set
Checked this site for most likely needed parts and ordered. Located full repair manual inside unit after removing lid. Followed instructions in manual to take apart and remove the drum; took pictures at each removal step and used pill organizer to keep screws in correct order and quantity. The metal cylinder in the center of the idler pul ley had ground away so the idler pulley with bracket was replaced. (There was a lot of metal dust that had to be cleaned.) One of the rollers did not turn smoothly so that was also replaced. After putting drum back in, reversed the steps to reassemble and referred to photos to make sure did in correct order and did not forget anything.
Was this helpful?
Thank you for voting!
door would not latch
4 of 4 people found this instruction helpful.
  • Paul from BENTONVILLE, AR
  • Very Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
removed old latch with pliers - inserted new latch
Was this helpful?
Thank you for voting!
No Heat sometimes, But for a moment then None
4 of 4 people found this instruction helpful.
  • Scott from Sacramento, CA
  • Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
First and Foremost i was told that my problem was with the Thermal Fuse (Fix Ya.com), Then with the little Electrical knowledge I have thought Fuses don't turn on and off,If the fuse was bad i would get No Heat. (Even for a second) Fuses just don't turn on and turn off intermittently,when they go there done! So after a little research i d ecided to order the gas coil valve. I tilted the top up, two screws on the front panel, took that off and the valves were exposed,(bottom left) two screws too remove bracket then installed new coils on bracket,put back together and I Have Heat Again! NO problems what so ever since new install. I would say having not been for cleaning lint build up inside the machine (been 6 years) the Whole project took me Ten Minutes.
Was this helpful?
Thank you for voting!
Gas dryer would not heat - pilot lit briefly then went off
5 of 7 people found this instruction helpful.
  • William from Chicago, IL
  • Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Same as others.
1. Unplug dryer from power source
2. Use nut driver to remove two front screws at bottom of dryer
3. Disconnect cable connected to Secondary Coil (this is the coil towards the rear of the dryer)
4. Use angled phillips screw driver to loosen screws holding cap on top of the two coils. (Angled tool not required but seemed easiest to me)
5. Slide top cap back towards lock screw to allow coil to be lifted out
6. Remove and replace secondary coil
7. Replace cap, tighten screws to lock in place, reconnect cable to coil
8. Restore power to dryer, test and confirm gas flame stays lit
9. Replace lower front panel on unit

PartsSelect a great resource to use for home repairs like these. My first time using site and doing this type of work, now PartsSelect my first source to go to on such items.
Was this helpful?
Thank you for voting!
No heat...
5 of 7 people found this instruction helpful.
  • Charles from Long Beach, CA
  • Easy
  • 30 - 60 mins
  • Socket set
Removed and replaced both the thermostat sensor and the ignitor. Tested thej dryer and it worked. Replaced the front panel and it was good to go.
Was this helpful?
Thank you for voting!
Dryer drum turned hard because rollers were worn
4 of 4 people found this instruction helpful.
  • Paul from STONE CREEK, OH
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
Remove top, front and drum. Top is removed by sliding a putty knife under the front corners and pushing the tabs back. Front is held with screws. Disconnect two electrical connectors. Rollers are easily accessible and changed.
Was this helpful?
Thank you for voting!
Sqeeking noise fron old worn belt and rollers
4 of 4 people found this instruction helpful.
  • Randy from HUNTSVILLE, AL
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
Watched instructions, Ordered the kit and repair was fairly easy until the time to line up the cover over the fan wheel. That was difficult part. Would be best to have two people at this point to hold it and align the screw holes. Otherwise its was a fairly easy operation.
Was this helpful?
Thank you for voting!
Very loud squeaking noise
5 of 7 people found this instruction helpful.
  • Philip from CHICAGO, IL
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
I removed all the panels, removed the tub, replaced the pulley, put the tub back in and replaced the panels. Just when I screwed the Last screw in the doorbell rang with the door switch which I installed immediately.
Was this helpful?
Thank you for voting!
My dryer was squeaking with an occasional thump
4 of 4 people found this instruction helpful.
  • Michael from BOILING SPGS, PA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Wrench set
Watched videos on line on how to repair. Replaced all four Drum Rollers, Belt and Idler Pulley, cleaned out inside of unit.
Was this helpful?
Thank you for voting!
Dryer was squealing
4 of 4 people found this instruction helpful.
  • Kevin from VALDOSTA, GA
  • Very Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Disconnected Power cord, removed vent pipe, removed back panel, had to slide top cover off to remove additional screw holding back on. Went down to where the Idler Pulley was, removed old piece by depressing on the spring loaded actuator and slid it off the belt and all. Replaced same as removal.
Was this helpful?
Thank you for voting!
Noisy when drum rotates
4 of 4 people found this instruction helpful.
  • lance from GREENSBURG, PA
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers
Used the maintenance kit....followed the movie tutorial. I also used an empty gallon plastic container to support the front of the drum while stretching the belt over the motor pulley. For the rear drum rollers, before sliding them on the shaft, I put a light grease film on the shaft. After the repair, the dryer runs quieter.
Was this helpful?
Thank you for voting!
Idler pulley seized
4 of 4 people found this instruction helpful.
  • John from CREST HILL, IL
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
The pulley is accessible from the back of the dryer. Disconnect the gas line. Remove all the screws. Also remove the small plate that secures the line cord. Lift the back up and out. I was able to avoid disconnecting the water line. Take a picture of the pulley so that you will have a record of the belt routing. Release the spring and rem ove and replace the pulley and bracket. Vacuum out the lint. Plug in the dryer to make sure that it works properly before reassembly.
Was this helpful?
Thank you for voting!
All Instructions for the 110781
121 - 135 of 573