110781 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Time clock not moving .Not enough heat
16 of 21 people
found this instruction helpful.
-
PHILIP from LONG ISLAND CITY, NY
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Opened front panel .Tested both coils on gas valve.
Found no continuity on one of the coils. Replaced coil,
dryer works like new.
Found no continuity on one of the coils. Replaced coil,
dryer works like new.
Was this helpful?
Thank you for voting!
Dryer would not turn
15 of 18 people
found this instruction helpful.
-
Kim K from Hurst, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
My dryer starter squeaking in December 09 and the repairman told me that it would cost between $200-$500. I did not let him fix it as this machine is only 3 years old. When the part finally broke in April 10, I was ready to junk this and just buy a used dryer. My husband went on line and quickly figured out the part he would need to do
... Read more
the repairs. It cost under $20.00. Now my dryer is fixed and running and there are no squeaks. Thank you
Read less
Was this helpful?
Thank you for voting!
Door latch wouldn't latch
14 of 16 people
found this instruction helpful.
-
Megan from Oxford, NC
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Like another reviewer's repair story, I decided to take the door apart. It was too difficult, at least for me, to get the faulty catch out without damaging either the the door or my hands. This is why I give it an "easy" rather than "very easy" rating and put the total repair time at a half hour or better. I also decided I wanted a second
... Read more
person to help - not with getting the door apart or putting it back together, but because a second pair arms was very helpful in rehanging the door well. We removed the door (four screws), marking which side of the hinge needed to be flush with the actual dryer when rehanging. Then we took the door apart, which comprises another sixteen screws (four on each edge). We used an electric drill but I'm sure it could be done manually. We used needle nosed pliers to get the faulty latch out of that side of the door, then replaced it with the "back up" from the other side. Then we put the door back together and carefully rehung it. Done. We did decide that, in future, all kids (we have three boys) slamming the door would be severely beaten. Pushing the door until it's against the dryer, then PUSHING (as opposed to slamming) the latch ONTO the catch pin on the dryer is obviously what was intended. However, I've learned not to count on my boys being particularly conscientious, so I'd ordered four replacement latches to keep on hand. This machine was delivered in April 2009 and I replaced the latch in April 2011. Based on this and our laundering habits, I'm sure the others will be used long before the dryer calls it quits.
Read less
Was this helpful?
Thank you for voting!
Dryer made a terrible screeching noise when tumbling.
13 of 14 people
found this instruction helpful.
-
Richard from SAUGERTIES, NY
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
I followed the repair Vedic and took the drum out and replaced the pulls and bracket. Very straightforward job. Dryer is now as quite as the first day we bought it.
Was this helpful?
Thank you for voting!
Brooken Dryer Door Catch
13 of 14 people
found this instruction helpful.
-
Ralph from Wheelersburg, OH
- Easy
- Less than 15 mins
-
Pliers
Removed the broken catch with a pair of needle nose pliars and replaced it the same way. Took about 10 minutes. Saved a Service Call
Was this helpful?
Thank you for voting!
Burner would not go on on my Stack Set Dryer
16 of 24 people
found this instruction helpful.
-
Robert from North East, PA
- Really Easy
- Less than 15 mins
-
Screw drivers
Took out two front Panel screws and removed the panel. Removed Gas solenoid coil holding bracket by removing two phillips head screws. Disconnected the coil leads. and removed the coils. Connected the new coils to the leads and set in place. Replaced the holding bracket and the two screws. Replaced the front cover and the two front
... Read more
cover screws. Piece of Cake!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
the dryer was making squealing noises when it first started.
13 of 15 people
found this instruction helpful.
-
Christine from BIRCH RUN, MI
- Really Easy
- 1- 2 hours
-
Nutdriver, Screw drivers
We watched the video at whirlpool.com! Made it so simple anyone could have done it!
Was this helpful?
Thank you for voting!
Quick and simple - quickest $100 I've ever saved!
13 of 16 people
found this instruction helpful.
-
Kelly from Waukegan, IL
- Really Easy
- Less than 15 mins
-
Screw drivers, Wrench (Adjustable)
Removed the two screws under the lint trap
Opened the top (had to use flathead screwdriver to release latches)
Disconnected door switch harness from front panel
Removed 2 screws holding front panel on dryer
Lifted out dryer drum (previous belt had broken)
Vacuumed inside of dryer (found $3 in quarters!)
Put n ... Read more ew belt around drum
Put drum back in dryer, using empty laundry soap bottle to support its weight
Looped belt around pulley and motor; secured pulley to dryer bottom
Made sure rear gasket thingy was aligned properly and drum turned freely
Put front panel back on
Re-attached door switch
Closed top and put screws back in under lint trap
Fired it up - WOOHOO!
Opened the top (had to use flathead screwdriver to release latches)
Disconnected door switch harness from front panel
Removed 2 screws holding front panel on dryer
Lifted out dryer drum (previous belt had broken)
Vacuumed inside of dryer (found $3 in quarters!)
Put n ... Read more ew belt around drum
Put drum back in dryer, using empty laundry soap bottle to support its weight
Looped belt around pulley and motor; secured pulley to dryer bottom
Made sure rear gasket thingy was aligned properly and drum turned freely
Put front panel back on
Re-attached door switch
Closed top and put screws back in under lint trap
Fired it up - WOOHOO!
Read less
Was this helpful?
Thank you for voting!
Dry was making a loud squeaking noise.
12 of 13 people
found this instruction helpful.
-
Michael from OREGON CITY, OR
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers
Just watch YouTube videos. They show you how step by step. Easy to install. Clean all the dust out while dryer is apart if you can with a vacuum.
Was this helpful?
Thank you for voting!
The Dryer would not get hot.
14 of 20 people
found this instruction helpful.
-
Jerry from Bradenton, FL
- Really Easy
- Less than 15 mins
-
Nutdriver
I removed the two screws holding the access panel, and removed the access panel. Then removed the lower air duct. I then checked the burner, The solenoid was not opeing the valve for the gas. I order the coils, in two day I had the coils and installed them. The dryer is working great.
Other Parts Used:
Was this helpful?
Thank you for voting!
dryer not heating up
12 of 14 people
found this instruction helpful.
-
Richard from New Windsor, NY
- Really Easy
- 15 - 30 mins
-
Screw drivers
Unscrewed 4 screws,pulled off front of machine.Unscrewed 2 screws holding coils on,unplugged coils,installed new coils,plugged in coils,reinstalled 2 screws for hold down brace.Reinstalled front cover,plugged dryer into outlet(remember to unplugged dryer before working on it).started up,instant heat,works great.thanks Partselect for helpi
... Read more
ng me out!!!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
The dryer was not fully drying
12 of 14 people
found this instruction helpful.
-
Michael from Chicago, IL
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers, Socket set
After replaceing several parts including the thermostats the last part I replaced the coils were the defective part. I originally metered out the themostats and they appeared to be okay but since this was my first time I thought I might have been mistaken. It turns out the last part I thought it could be was the part that was defective. I
... Read more
will say that it is very simple to replace any of the parts involved. The hardest part was trying to open the dryer itself. But after having to do it 3 times, I'm now a pro. I also replaced the drum belt and since I had it open I also replaced the belf idler with a newer modified idler rolller.
Putting the belt back on is easy, but it helps to view the video or a picture to understand how the belt goes around it.
Putting the belt back on is easy, but it helps to view the video or a picture to understand how the belt goes around it.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
When using the dryer the cycle would stop and display E1 as the reason
13 of 18 people
found this instruction helpful.
-
Joyce from Holbrook, NY
- Really Easy
- 15 - 30 mins
-
Screw drivers
Unscrewed the bottom panelof the dryer and located the thermistor through the schematic for my machine. Removed the old one and put the new one in the same way. No more E1 problems and all cycles now complete themselves.
Was this helpful?
Thank you for voting!
Scratches in Surface
83 of 228 people
found this instruction helpful.
-
Michelle from Richardson, TX
- Really Easy
- Less than 15 mins
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this helpful?
Thank you for voting!
Bearings wore out of drum rollers
11 of 12 people
found this instruction helpful.
-
Judy from Kalamazoo, MI
- Easy
- Less than 15 mins
-
Screw drivers
I raised the top of the dryer, removed the front, the belt and the drum. Slipped off old rollers, installed new ones and new tensioner. Reinstalled drum and belt, bolted front back on and closed the top.
Was this helpful?
Thank you for voting!