110781 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Scratches in Surface
83 of 228 people
found this instruction helpful.
-
Michelle from Richardson, TX
- Really Easy
- Less than 15 mins
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this helpful?
Thank you for voting!
Broken belt. Broken idle pully and replace 4 rollers
11 of 14 people
found this instruction helpful.
-
Mike from INOLA, OK
- Easy
- More than 2 hours
-
Nutdriver, Screw drivers, Socket set
By watching the video it made the job much easier than I thought it would be. I was very pleased with the speedy delivery of the Dryer kit I had ordered. I had called a local repair facility and they wanted twice as much for the same parts.
Was this helpful?
Thank you for voting!
Idler pulley wore out
10 of 11 people
found this instruction helpful.
-
Peter from HUEYTOWN, AL
- Very Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Removed the back panel and saw that the idler pulley was worn out. It only took me 5min. To replace, it was very easy to replace.
Was this helpful?
Thank you for voting!
Close would not get dry. Dryer started normal. Timer would not time out.
12 of 18 people
found this instruction helpful.
-
Roger from Westminster, SC
- Very Difficult
- More than 2 hours
-
Nutdriver, Screw drivers
Getting to any of the parts in the Maytag dryer is easy. Tip the dryer back and slide a 4 x 4 block under the front edge. You remove the whole front panel after you remove two screws at the bottom corners of the front panel. You need to tip the dryer back to get a screwdriver on the screws. Swing the front panel up to release the top of t
... Read more
he door panel from the top. Watch the short wires to the door switch. Unhook the door switch wires and move the front panel out of the way. The timer on the top is accessed by re-moving two screws along the top edge. There are four screws. Remove them all and tip the top of the front panel forward. You then see that two screws hold the panel and the other two screws just hold the trim.
The dryer started normal. The drum motor run when the start button was operated. The fluff cycle operated normal to indicate the timer motor was OK. On the dry cycles, the igniter heated up. The gas came on. The dryer run for some period of time and then the flame went off. The thought was that the low temp cycle thermostat sensed the dryer was hot and thus switched over to time the cycle to its end. However, the low temp cycle thermostat tested good with a meter when the sensor was removed from the dryer and heated with a light bulb. Burnt contacts in the sensor were a possible problem. I also though the radiant sensor may be bad and not recycling after it got hot. After time, the igniter would cycle on but the gas flame would not come on. I thought the radiant heater might not be tripping the secondary coil on the gas valve. The gas valve coils tested good. I was checking them cold after the dryer had cooled down. I ordered a number of parts.
I got lucky and did a test on the coils while the dryer was still hot. One of the coils in the dual booster holding coil was going open when hot. When cold it had enough continuity to let the gas valve cycle on once. After the coil got warm it went open and shut the gas valve off. When the coil did cool off, it again had continuity. I was about ready to trash the dryer when I finely found the problem. I am happy I persisted and worked the problem through to a solution. I purchased several extra sensors but saved money in the long-run. I rate this problem at the high end of complexity for the do-it your self home owner to solve. The problem was an easy fix once the real problem was found. Only 4 screws and 3 push on wire connectors (two were on the front panel for the door switch).
The dryer started normal. The drum motor run when the start button was operated. The fluff cycle operated normal to indicate the timer motor was OK. On the dry cycles, the igniter heated up. The gas came on. The dryer run for some period of time and then the flame went off. The thought was that the low temp cycle thermostat sensed the dryer was hot and thus switched over to time the cycle to its end. However, the low temp cycle thermostat tested good with a meter when the sensor was removed from the dryer and heated with a light bulb. Burnt contacts in the sensor were a possible problem. I also though the radiant sensor may be bad and not recycling after it got hot. After time, the igniter would cycle on but the gas flame would not come on. I thought the radiant heater might not be tripping the secondary coil on the gas valve. The gas valve coils tested good. I was checking them cold after the dryer had cooled down. I ordered a number of parts.
I got lucky and did a test on the coils while the dryer was still hot. One of the coils in the dual booster holding coil was going open when hot. When cold it had enough continuity to let the gas valve cycle on once. After the coil got warm it went open and shut the gas valve off. When the coil did cool off, it again had continuity. I was about ready to trash the dryer when I finely found the problem. I am happy I persisted and worked the problem through to a solution. I purchased several extra sensors but saved money in the long-run. I rate this problem at the high end of complexity for the do-it your self home owner to solve. The problem was an easy fix once the real problem was found. Only 4 screws and 3 push on wire connectors (two were on the front panel for the door switch).
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer squeeching very loud
9 of 9 people
found this instruction helpful.
-
Michael from ENOLA, PA
- Very Easy
- 15 - 30 mins
-
Nutdriver, Socket set
Took off back of dryer Undid belt from belt adjuster pulled and took off adjuster put new one on redid belt and put back on dryer. Done
Other Parts Used:
Was this helpful?
Thank you for voting!
Gas Dryer would heat for one heating cycle but no gas afterward. Ignitor would glow.
10 of 12 people
found this instruction helpful.
-
Jim from Foothill Ranch, CA
- Easy
- 15 - 30 mins
-
Screw drivers
Checked four thermocouples all showed continuity with my multimeter so they were all good. I'd read that the coils commonly went out and that these were the symptoms. Hey, it's very simple in there. Not much else could be wrong. I had a Maytag repairman come out. At first he said the problem was a blocked vent. I knew he was wrong. Then h
... Read more
e said one of the thermocouples went out. It was $80 for him to come out. It turned out that his second diagnosis was wrong too. To repair the dryer by Maytag would have cost me $240. I gave him $80 and bought the coils for $37. They are EXTREMELY easy to replace: two screws held a bracket that held two coils. With the bracket off, I took off the old coils and slid on the new ones.
Read less
Was this helpful?
Thank you for voting!
The main knob insert snapped.
11 of 16 people
found this instruction helpful.
-
Larry from HICKORY, NC
- Very Easy
- Less than 15 mins
Nothing to it. Just remember to put the insert in the knob, NOT on the selector stem. Line up the flat part of the insert with the flat part of the stem and push the knob in place.
Don NOT ram it on the selector stem. When it's seated, don't push any more. That's all there is to it. It works. If the pointer on the knob indicat ... Read more es the selector is lined up correctly, but it isn't, the problem is the selector, not the knob.
Don NOT ram it on the selector stem. When it's seated, don't push any more. That's all there is to it. It works. If the pointer on the knob indicat ... Read more es the selector is lined up correctly, but it isn't, the problem is the selector, not the knob.
Read less
Was this helpful?
Thank you for voting!
latch on door broke
11 of 16 people
found this instruction helpful.
-
donna from westmoreland, TN
- Easy
- Less than 15 mins
-
Pliers
very easily
Was this helpful?
Thank you for voting!
Rollers were wore out
9 of 10 people
found this instruction helpful.
-
Chandra from Orange, CA
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Just follow the instructions the one was provided with Maitanace kit we bought from you.
Was this helpful?
Thank you for voting!
Broken dryer door catch
9 of 11 people
found this instruction helpful.
-
Preston from ETNA, OH
- Really Easy
- Less than 15 mins
Used the screwdriver pressed the blade against the edge of the door catch and popped it out. Put the new door catch in place and pressed it and it snapped into place. Done
Was this helpful?
Thank you for voting!
Catch was broken
9 of 11 people
found this instruction helpful.
-
Rosemary from RILEY, MI
- Very Easy
- Less than 15 mins
Removed the plastic guard. Snapped the catch in place and replaced the guard
Was this helpful?
Thank you for voting!
No Heat
9 of 12 people
found this instruction helpful.
-
NICHOLAS from PARMA, OH
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers, Wrench set
I suspected a faulty igniter and disconnected the cable to the igniter and measured the resistance of the igniter and found it to be 70 ohms then I checked the voltage at the same cable towards the power source and found it to be 25 volts ac which should be 120 volts ac. Next I checked the radiant flame sensor and found it to be open (i
... Read more
t should be a closed circuit when cold). I removed the flame sensor (with the power off) using a small box wrench and found a broken lead. Replacing the flame sensor solved the problem.
Read less
Was this helpful?
Thank you for voting!
My dryer made squeaking noise when rotating.
8 of 9 people
found this instruction helpful.
-
James from KENNESAW, GA
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers
I followed directions found on several similar YouTube videos since the instructions included in the Whirlpool parts kit were not for my model dryer. I found that the original idler pulley was not rotating and the belt had worn a groove through it. I replaced all 4 roller wheels, idler pulley and the belt. Problem solved.
Was this helpful?
Thank you for voting!
The seal came off our dryer door.
10 of 15 people
found this instruction helpful.
-
Janet from LOS ANGELES, CA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Take door off dryer (unscrew four screws). Lay door on flat surface. Using glue provided glue down new seal. Put dryer door back on and you're done!
Was this helpful?
Thank you for voting!
dryer would not heat or turn off
9 of 12 people
found this instruction helpful.
-
michael from eldridge, IA
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set, Wrench (Adjustable)
removed front of dryer located igniter removed two screws disconnected wires then put new one in also replace thermal fuse and thermostat on back of dryer works great.
Was this helpful?
Thank you for voting!