110781 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
no heat
31 of 40 people
found this instruction helpful.
-
rex from streator, IL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Wrench (Adjustable)
the ignitor did not glow red checked thermal fuse by exhaust duct. fuse open replaced thermal fuse
Was this helpful?
Thank you for voting!
converting to LP gas
30 of 37 people
found this instruction helpful.
-
Robert from Tenino, WA
- Easy
- 15 - 30 mins
-
Socket set, Wrench (Adjustable)
First I removed the front panel which allowed access to the burner assembly. Then I removed the gas connector and elbow from the back of the dryer. Then I removed 2 screws that hold burner assembly in place and 2 screws that hold an angle brace for the burner assembly. Had to loosen the screw that clamps around the gas pipe holding it in
... Read more
place clear in the back inside dryer housing. Unplugged all wiring connectors, then I removed the burner assembly and removed the 2 screws holding the burner tube to the valve. Remove the orifice and replaced with the proper size for LP gas. Then removed the blocking pin and replaced with one for LP gas. Then reassembled in reverse order. Actually pretty easy.
Read less
Was this helpful?
Thank you for voting!
Dyer drum doesnt turn
27 of 29 people
found this instruction helpful.
-
Shawn from Akron, OH
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
It was really quite esy remove the screws from the back and pop the top off . then remove 2 top inside screws from the front , lift the front off the sides , support the drum and lift out , you will then see the idler wheels, replace them with the new ones ,replce the tensioner , wrap the belt around the drum, need help putting the drum b
... Read more
ack in the case, have someone hold the drum in place while you lay on the ground and put the belt around the motor pulley and the tensioner on the bottom.you then put the front panel back into place and secure with the 2 inside screws, then put the rest back together in reverse oder. ... hope this helps someone
Read less
Was this helpful?
Thank you for voting!
Dryer door wouldn't 'latch' closed.
26 of 27 people
found this instruction helpful.
-
Christopher from Oceanport, NJ
- Easy
- 15 - 30 mins
-
Screw drivers
took off about 8 screws, opened door into it's front & back parts, popped out the old/broken door catches and re-inserted replacements. Only 1 is needed, but this is the 2nd one to break. The first time a repairman switch the un-used from right side to left. (there are 2 so the door can be hung left or right opening)
Was this helpful?
Thank you for voting!
Dryer would dry for 5-10 minuets then no heat
35 of 55 people
found this instruction helpful.
-
Richard from Jerome, MI
- Easy
- Less than 15 mins
-
Screw drivers, Socket set
I tested the dryer coils and found that they were getting a voltage but would not open the gas valve. Coils were not bad but weak. After they warmed up they would not open the gas valve. It took 10 min to repace both coils and the heat sensor.
Other Parts Used:
Was this helpful?
Thank you for voting!
Unit would shut down in the middle of cycle and flash E1 trouble code
30 of 41 people
found this instruction helpful.
-
Jim from Tucson, AZ
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers, Socket set
Had to remove the back of unit to access the area of subject part by removeing 12 to 14 screws also the gas line had to be removed. Two screws held the part in place. Unit now runs normal.Saved alot on repair costs!!!!!
Was this helpful?
Thank you for voting!
Drayer Was Making Squeaking Sound
26 of 30 people
found this instruction helpful.
-
Charles from Gray, TN
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
Took off the top and front panel. Found that the belt tensioner was worn out. Decided to pull drum out,and replace the belt and drum rollers also. Put it back together, and it works fine.
Was this helpful?
Thank you for voting!
Dryer was making a screaching noise while turning
24 of 24 people
found this instruction helpful.
-
jose from FALLBROOK, CA
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Repaired the 4 drum support rollers, 1 idler assembly, 9 tri rings, and 1 washer that came with the kit, however, the multi rib dryer belt that came with the kit did not fit my dryer. After several attempts to troubleshoot the problem, I realized that the belt was too small. I contacted PartSelect customer service and advised that the
... Read more
multi rib dryer belt that came with the kit was too small and I need to purchase a belt (P/N WP8547157) that fits my dryer. Adam was very courteous and helpful and very apologetic for the belt not being the right one. PartSelect refunded my purchase for the Parts Kit and I purchased the correct multi rib dryer belt. I received the new belt expeditiously and was able to finalize the repairs. Thank you PartSelect for your support and cooperation. Recommend: Advise customers that the belt in the kit may not fit the recommended dryer.
Read less
Was this helpful?
Thank you for voting!
Dryer would not heat up.
26 of 30 people
found this instruction helpful.
-
Roger from Bonners Ferry, ID
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
I unplugged the dryer,removed the two small screws on the front of the dryer and pulled the bottom forward. The two wires connected to the door do not have to be removed. With an electrical tester using the Ohm setting I tested the Radiant sensor and the Gas Valve coils. The two terminal coil was DOA. The dryer can be operated with the f
... Read more
ront open as long as the door wires are connected. Symptons: The igniter would heat up and not release gas. My repair was successfull due to this awesome website and the super fast shipping service. AAAA++++
Read less
Was this helpful?
Thank you for voting!
noisy drum
29 of 40 people
found this instruction helpful.
-
Jeff from Mesa, AZ
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
the job would have gone faster if the right parts had been sent in the first place. I would have never paid for two day shipping. In the repair, I removed the rear panel, clipped the plastic triangle holding the bearing, installed the new bearing and new clip.
Was this helpful?
Thank you for voting!
craked blower motor
63 of 144 people
found this instruction helpful.
-
joe from cheswick, PA
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
somthing fell down in the blower motor compartment and busted up the bloewr motor fan,and was making noise and out of balance.i changed the blower motor and runs like a charme
Was this helpful?
Thank you for voting!
Noisy Dryer
22 of 22 people
found this instruction helpful.
-
Patrick from SCHENECTADY, NY
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers
I ordered the dryer repair kit and to my surprise it arrived 4 days early. I followed the video instructions on the parts select website to replace 4 rollers, belt and belt pulley. A 1/4 in nut driver attached to my Dewalt drill made life ALOT easier!! My recommendation, when you remove the rollers, take a rag and really clean up the shaf
... Read more
t they ride on. Then apply a lightweight spray oil to the shafts. When you install the new rollers they will spin free and easy. Having the dryer apart is also a great time to break out the dust buster of vacuum. Spin the fan motor up front by hand and use vacuum to remove lint or belt shaving from inside the cabinet. Add this step as good fire prevention measure.
Read less
Was this helpful?
Thank you for voting!
dryer stoped heating
23 of 26 people
found this instruction helpful.
-
valerie from Elasmore, KS
- Really Easy
- 15 - 30 mins
-
Nutdriver
the problem was not the igniter its was the thermal fuse I broke the igniter during inspection of the problem be careful its a very easy thing to break repairs complete thank you parts select for the quick shipping and low prices
Was this helpful?
Thank you for voting!
Dyer would not heat, flame would shut off within 10 seconds
24 of 29 people
found this instruction helpful.
-
Christy from Riley, MI
- Easy
- Less than 15 mins
-
Screw drivers, Socket set
I opened the panel, undid the plugs, detached the radiant sensor by undoing one screw and removed and replaced the part. Fairly simply.
Was this helpful?
Thank you for voting!
Belt broke, dryer stopped.
24 of 30 people
found this instruction helpful.
-
Richard from Groveland, MA
- Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Replaced the belt and the wheels supplied with the kit. I also cleaned the inside of the unit. It looks and works like new.
Was this helpful?
Thank you for voting!