110780 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
seal for lint filter came off
17 of 23 people
found this instruction helpful.
-
John from Midland, TX
- Really Easy
- Less than 15 mins
Pulled out the old and slid in the new filter
Was this helpful?
Thank you for voting!
Door would come open while drying clothes
21 of 35 people
found this instruction helpful.
-
Mark from Charlotte, NC
- Really Easy
- Less than 15 mins
-
Nutdriver
Very bad design to keep door shut but very simple to fix. Just screw bad strike out and screw new one end. Whirlpool should have gave extra when you buy this type dryer.
Was this helpful?
Thank you for voting!
Time clock not moving .Not enough heat
16 of 21 people
found this instruction helpful.
-
PHILIP from LONG ISLAND CITY, NY
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Opened front panel .Tested both coils on gas valve.
Found no continuity on one of the coils. Replaced coil,
dryer works like new.
Found no continuity on one of the coils. Replaced coil,
dryer works like new.
Was this helpful?
Thank you for voting!
Dryer would not turn
15 of 18 people
found this instruction helpful.
-
Kim K from Hurst, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
My dryer starter squeaking in December 09 and the repairman told me that it would cost between $200-$500. I did not let him fix it as this machine is only 3 years old. When the part finally broke in April 10, I was ready to junk this and just buy a used dryer. My husband went on line and quickly figured out the part he would need to do
... Read more
the repairs. It cost under $20.00. Now my dryer is fixed and running and there are no squeaks. Thank you
Read less
Was this helpful?
Thank you for voting!
Loud sreeching and vibration
14 of 15 people
found this instruction helpful.
-
Robert from TUTTLE, OK
- Really Easy
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
I just followed the videos I received with the order and everything went really well. This dryer was a little different than the video, but the process was the same. The HE3 does require 4 drum rollers and I had only ordered 2. However, there was only one bad roller, so I installed both on the back of the drum. The two front rollers are
... Read more
pretty easy to get to if they go bad. The idler pulley was completely worn out with an 1/8 inch groove worn off to one side. PartSelect made this an easy project!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Door latch wouldn't latch
14 of 16 people
found this instruction helpful.
-
Megan from Oxford, NC
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Like another reviewer's repair story, I decided to take the door apart. It was too difficult, at least for me, to get the faulty catch out without damaging either the the door or my hands. This is why I give it an "easy" rather than "very easy" rating and put the total repair time at a half hour or better. I also decided I wanted a second
... Read more
person to help - not with getting the door apart or putting it back together, but because a second pair arms was very helpful in rehanging the door well. We removed the door (four screws), marking which side of the hinge needed to be flush with the actual dryer when rehanging. Then we took the door apart, which comprises another sixteen screws (four on each edge). We used an electric drill but I'm sure it could be done manually. We used needle nosed pliers to get the faulty latch out of that side of the door, then replaced it with the "back up" from the other side. Then we put the door back together and carefully rehung it. Done. We did decide that, in future, all kids (we have three boys) slamming the door would be severely beaten. Pushing the door until it's against the dryer, then PUSHING (as opposed to slamming) the latch ONTO the catch pin on the dryer is obviously what was intended. However, I've learned not to count on my boys being particularly conscientious, so I'd ordered four replacement latches to keep on hand. This machine was delivered in April 2009 and I replaced the latch in April 2011. Based on this and our laundering habits, I'm sure the others will be used long before the dryer calls it quits.
Read less
Was this helpful?
Thank you for voting!
Thermal fuse was bad.
16 of 22 people
found this instruction helpful.
-
Brad from Odessa, MO
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Did an Ohm test on the old Thermal Fuse found it to be bad. Replaced it with a new and the dryer is back to working great. Your suggestions saved approximatley $150.
Thanks for the help.
Thanks for the help.
Was this helpful?
Thank you for voting!
Brooken Dryer Door Catch
13 of 14 people
found this instruction helpful.
-
Ralph from Wheelersburg, OH
- Easy
- Less than 15 mins
-
Pliers
Removed the broken catch with a pair of needle nose pliars and replaced it the same way. Took about 10 minutes. Saved a Service Call
Was this helpful?
Thank you for voting!
Dryer gasket detached from screen
14 of 17 people
found this instruction helpful.
-
Richard from Duarte, CA
- Really Easy
- Less than 15 mins
Received in two days, open box, installed part. Pretty easy, fast service. I'm a repeat customer and will use these guys in the future.
Was this helpful?
Thank you for voting!
Dryer made a terrible screeching noise when tumbling.
13 of 14 people
found this instruction helpful.
-
Richard from SAUGERTIES, NY
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
I followed the repair Vedic and took the drum out and replaced the pulls and bracket. Very straightforward job. Dryer is now as quite as the first day we bought it.
Was this helpful?
Thank you for voting!
Lint has been bypassing the lint filter and building up in the fan (and duct)
12 of 12 people
found this instruction helpful.
-
David from PINETOWN, NC
- Really Easy
- Less than 15 mins
I noticed that drying time was increasing. I took the covers off the dryer to reach the fan and discovered that the squirrel cage fan buckets were packed with lint, and therefore not moving the air as intended. This was because the original lint filter caught most of the lint, but some bypassed the lint filter and then built up in the fan
... Read more
wheel buckets. The lint bypassed the lint filter because there was no felt gasket on the original filter as far as I can tell. I replaced the lint filter...and the replacement filter includes the felt seal (and fits tightly in the slide). The original lint filter has a provision for the felt seal, but I don't recall ever seeing it (and I did not see remnants of it in the fan or duct). As a matter of fact, I was always suspicious of how loosely the lint filter fit in the slide. The felt seal is not available as a replacement part from Maytag. That said, felt material 3/16"x1/2"x10ft is available from McMaster-Carr...and it fits nicely in the original lint filter.
Read less
Was this helpful?
Thank you for voting!
Burner would not go on on my Stack Set Dryer
16 of 24 people
found this instruction helpful.
-
Robert from North East, PA
- Really Easy
- Less than 15 mins
-
Screw drivers
Took out two front Panel screws and removed the panel. Removed Gas solenoid coil holding bracket by removing two phillips head screws. Disconnected the coil leads. and removed the coils. Connected the new coils to the leads and set in place. Replaced the holding bracket and the two screws. Replaced the front cover and the two front
... Read more
cover screws. Piece of Cake!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
the dryer was making squealing noises when it first started.
13 of 15 people
found this instruction helpful.
-
Christine from BIRCH RUN, MI
- Really Easy
- 1- 2 hours
-
Nutdriver, Screw drivers
We watched the video at whirlpool.com! Made it so simple anyone could have done it!
Was this helpful?
Thank you for voting!
Defective Door Switch
12 of 13 people
found this instruction helpful.
-
George from Bedford, TX
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Opened the lid and removed screws hollding switch to cabinet. Had to use magnifying glass to find locking mechanism on the electrical harness. Used small bladed screwdiver from my computer maintenaqnce kit to disengae lock. Hooked up harness. Replaced screws and shut lid. Main difficulty is my near vision. Requires use of a magnifier I a
... Read more
m 80 years old). Your video is great. Gives step by step instructions.
Read less
Was this helpful?
Thank you for voting!
Dry was making a loud squeaking noise.
12 of 13 people
found this instruction helpful.
-
Michael from OREGON CITY, OR
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers
Just watch YouTube videos. They show you how step by step. Easy to install. Clean all the dust out while dryer is apart if you can with a vacuum.
Was this helpful?
Thank you for voting!