110780 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
noisy drum
29 of 40 people
found this instruction helpful.
-
Jeff from Mesa, AZ
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
the job would have gone faster if the right parts had been sent in the first place. I would have never paid for two day shipping. In the repair, I removed the rear panel, clipped the plastic triangle holding the bearing, installed the new bearing and new clip.
Was this helpful?
Thank you for voting!
Broken door switch
24 of 27 people
found this instruction helpful.
-
Michael from Maricopa, AZ
- Really Easy
- 15 - 30 mins
-
Screw drivers
Followed your online video for disassembly and it was not only educational but actually quite simple. I would recommend that you start the video with," make sure the power cord is disconnected from the power source". I have worked on numerous pieces of large electrical equipment and would strongly suggest this be added. Some people think
... Read more
if it's, "off", it's safe. Your phone staff when ordering was great. We will do business again.
Read less
Was this helpful?
Thank you for voting!
craked blower motor
63 of 144 people
found this instruction helpful.
-
joe from cheswick, PA
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
somthing fell down in the blower motor compartment and busted up the bloewr motor fan,and was making noise and out of balance.i changed the blower motor and runs like a charme
Was this helpful?
Thank you for voting!
Noisy Dryer
22 of 22 people
found this instruction helpful.
-
Patrick from SCHENECTADY, NY
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers
I ordered the dryer repair kit and to my surprise it arrived 4 days early. I followed the video instructions on the parts select website to replace 4 rollers, belt and belt pulley. A 1/4 in nut driver attached to my Dewalt drill made life ALOT easier!! My recommendation, when you remove the rollers, take a rag and really clean up the shaf
... Read more
t they ride on. Then apply a lightweight spray oil to the shafts. When you install the new rollers they will spin free and easy. Having the dryer apart is also a great time to break out the dust buster of vacuum. Spin the fan motor up front by hand and use vacuum to remove lint or belt shaving from inside the cabinet. Add this step as good fire prevention measure.
Read less
Was this helpful?
Thank you for voting!
Dyer would not heat, flame would shut off within 10 seconds
24 of 29 people
found this instruction helpful.
-
Christy from Riley, MI
- Easy
- Less than 15 mins
-
Screw drivers, Socket set
I opened the panel, undid the plugs, detached the radiant sensor by undoing one screw and removed and replaced the part. Fairly simply.
Was this helpful?
Thank you for voting!
dryer stoped heating
23 of 26 people
found this instruction helpful.
-
valerie from Elasmore, KS
- Really Easy
- 15 - 30 mins
-
Nutdriver
the problem was not the igniter its was the thermal fuse I broke the igniter during inspection of the problem be careful its a very easy thing to break repairs complete thank you parts select for the quick shipping and low prices
Was this helpful?
Thank you for voting!
Dryer turns off after 1-2 minutes
23 of 27 people
found this instruction helpful.
-
Dixon from Santa Fe, NM
- Easy
- 30 - 60 mins
-
Nutdriver
I tried to follow directions followed by others on this site after diagnosing the problem via suggestions provided by users. I have a Whirlpool Duet dryer from 2002. We've had problems since moving about 3 years ago. I removed the front panel (lower) by unscrewing the two bottom screws (1/4" sheet metal screws). Then I took out the lint s
... Read more
creen and the metal tube/contraption immediately beneath to get access to the area where thermistor is located. See the drawing/chart to help you locate this. It's really easier than it seems. Make sure you have the chart/drawing for your model - it makes difference! The thermistor came out pretty easily with a nutdriver that has a swivel offset shaft. Ask your hardware store tool dept. about that one. Put everything back in reverse order of course and test either with/without the front panel re-attached. In my case it fixed at least part of the problem. I was able to get clothes almost dry with most settings but I have yet to install the moisture sensor to see if that helps in addition to the internal-bias thermistor. I am the kind of person that does one thing at a time so at least I now know the thermistor was bad. Good luck and hang in there with your own repair. It's a lot cheaper even if it takes you longer to do than a pro.
Read less
Was this helpful?
Thank you for voting!
Poorly designed lint filter/ gasket falls off
25 of 34 people
found this instruction helpful.
-
John from Madison, WI
- Really Easy
- Less than 15 mins
Replaced
Was this helpful?
Thank you for voting!
Needed to change rear exhaust to the side to fit dryer into my closet.
44 of 91 people
found this instruction helpful.
-
Mark from San Diego, CA
- Really Easy
- 30 - 60 mins
-
Screw drivers, Wrench (Adjustable)
First, I opened up the front of the dryer and then unscrewed the entire back piece. I assembled the new exhaust piece from the kit. Next, I took out the old straight rear exhaust and then replaced it with the elbow shaped left eshaust from the kit. Lastly, reattache the back and front pieces of the dryer.
Was this helpful?
Thank you for voting!
Dryer working but drum light not working, bulb ok.
22 of 27 people
found this instruction helpful.
-
Denton from Indianapolis, IN
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Problem: Drum light not working, bulb ok. Removed 6 screws on panel behind timer, light, buzzer, switches. Lifted back of dryer top then moved dryer top forward and off of dryer. The switch was located above the door. Unhooked wiring plug and took out 2 screws holding in the switch. Installed new switch and repaced bulb. Reassembled as ne
... Read more
eded and tested light by opening door. Works great.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
The Dryer Would Not Turn On
19 of 19 people
found this instruction helpful.
-
Ribhe from Wildwood, MO
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
The dryer wouldn’t turn on at all. It was like it was unplugged from the wall. However, fixing it couldn't be easier. I simply removed the back panel, found the fuse, tested it with an Ohmmeter (to determine that this was the part that didn't work), ordered the part from this website, and replaced the part. The part arrived in about t
... Read more
wo days. The shipping was a little pricey, but overall the whole thing cost me $20 vs. whatever it would cost me to get someone else to repair it. The website helps to identify the problem, and it is helpful to read how other people fixed their problems. It was so easy and the service was so good, I will definitely use this website again and recommend it to others.
Read less
Was this helpful?
Thank you for voting!
The dryer stopped working and would not start.
20 of 22 people
found this instruction helpful.
-
kevin from Saint Augustine, FL
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers, Socket set
After unplugging the dryer, I removed the bottom panel in front. Remove the the filter inside the dryer and remove the filter housing below. There you can see the thermal fuse on the air duct, its white with two blue wires. You can check it with a ohmmeter after removing the wires. If its open its bad. Its held in place with two sheet met
... Read more
al screws. After replacing the thermal fuse the dryer worked fine. However I would suggest cleaning the air duct and the outside discharge opening. Hope this helps.
Read less
Was this helpful?
Thank you for voting!
Noisy sound from dryer
20 of 23 people
found this instruction helpful.
-
john from OLYMPIA, WA
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers
Just like video except there were two screws in back to take control head off. Be prepared to have shop vacation ready. Clean dryer duct too. Have bandaids ready. Plastic triangles are not easy to take off, video makes it look easy.
Was this helpful?
Thank you for voting!
Idler Pulley broke
21 of 26 people
found this instruction helpful.
-
Keith from Richmond, VA
- Really Easy
- 15 - 30 mins
-
Socket set
I disconnect the power, then the vent pipe. I removed the back panel of the dryer to access the pulley and removed the belt. Replaced the back and put everything back together.
Was this helpful?
Thank you for voting!
Would not heat sometimes
21 of 26 people
found this instruction helpful.
-
Chris from Laguna Niguel, CA
- Easy
- 15 - 30 mins
-
Screw drivers
Pulled the big front panel by removing two screws near bottom of front and pulling out at bottom until the top pops loose. Vacuumed out all of the dust and checked for loose connections. Ran dryer - igniter would light, but no gas. Checked the two solenoids with a VOM. the one with the two leads would intermittently read Infinity (open).
... Read more
Super simple repair. Remove two screws on solenoid bracket on top of the gas valve, Replace solenoid and plug it back in with the easy push-on connector. NO PROBLEM - all fixed.
Read less
Was this helpful?
Thank you for voting!