110780 Kenmore Dryer - Instructions

All Instructions for the 110780
121 - 135 of 1248

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Close would not get dry. Dryer started normal. Timer would not time out.
12 of 18 people found this instruction helpful.
  • Roger from Westminster, SC
  • Very Difficult
  • More than 2 hours
  • Nutdriver, Screw drivers
Getting to any of the parts in the Maytag dryer is easy. Tip the dryer back and slide a 4 x 4 block under the front edge. You remove the whole front panel after you remove two screws at the bottom corners of the front panel. You need to tip the dryer back to get a screwdriver on the screws. Swing the front panel up to release the top of t he door panel from the top. Watch the short wires to the door switch. Unhook the door switch wires and move the front panel out of the way. The timer on the top is accessed by re-moving two screws along the top edge. There are four screws. Remove them all and tip the top of the front panel forward. You then see that two screws hold the panel and the other two screws just hold the trim.

The dryer started normal. The drum motor run when the start button was operated. The fluff cycle operated normal to indicate the timer motor was OK. On the dry cycles, the igniter heated up. The gas came on. The dryer run for some period of time and then the flame went off. The thought was that the low temp cycle thermostat sensed the dryer was hot and thus switched over to time the cycle to its end. However, the low temp cycle thermostat tested good with a meter when the sensor was removed from the dryer and heated with a light bulb. Burnt contacts in the sensor were a possible problem. I also though the radiant sensor may be bad and not recycling after it got hot. After time, the igniter would cycle on but the gas flame would not come on. I thought the radiant heater might not be tripping the secondary coil on the gas valve. The gas valve coils tested good. I was checking them cold after the dryer had cooled down. I ordered a number of parts.

I got lucky and did a test on the coils while the dryer was still hot. One of the coils in the dual booster holding coil was going open when hot. When cold it had enough continuity to let the gas valve cycle on once. After the coil got warm it went open and shut the gas valve off. When the coil did cool off, it again had continuity. I was about ready to trash the dryer when I finely found the problem. I am happy I persisted and worked the problem through to a solution. I purchased several extra sensors but saved money in the long-run. I rate this problem at the high end of complexity for the do-it your self home owner to solve. The problem was an easy fix once the real problem was found. Only 4 screws and 3 push on wire connectors (two were on the front panel for the door switch).
Was this helpful?
Thank you for voting!
Door handle had shattered
9 of 9 people found this instruction helpful.
  • Fred from BRADENTON, FL
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
Removed the door after some trial and error attempts. Door handle should come with instructions. Nothing but the handle was in the package. YouTube videos did not cover this model.
Remove the screws holding the hinges to the door, one on each hinge. Pull the door straight up from the hinges. Be careful, the hinges have springs that s hut the door. Once the door is off, remove the screws around the four edges. Separate the front from the inside of the door. Set the inside of the door aside. Remove the flanged nuts from the inside of the door. There may be other screws to remove and save. Save the nuts for reinstallation.
Remove the handle. Replace with the new handle and reuse the flanged nuts and screws to install the handle. Reassemble the door (there may be a piece of cardboard inside for sound proofing) and slide it back onto the hinges. Replace hinge screws. Walla, you’re done.
Was this helpful?
Thank you for voting!
gasket came off lent filter
11 of 15 people found this instruction helpful.
  • stephen from langley, KY
  • Really Easy
  • Less than 15 mins
i could not find this part anywhere locally,so i found this web site which had this part.i ordered this part and am very glad i did.i received it in 2 days.thank you very much.if you need anything check this place first,you will be very satisfied.
Was this helpful?
Thank you for voting!
my teenage son was messing around and got into the dryer and broke the door catch and bent the door.
13 of 21 people found this instruction helpful.
  • Dawn from Chesapeake City, MD
  • Really Easy
  • Less than 15 mins
removed the catch and the pin and replaced it. We were sent a couple different sizes so we tested the one that looked like the closest match. I think the pin was made with different thicknesses of metal. Worked great and saved us from having to get a new dryer!
Was this helpful?
Thank you for voting!
Gas Dryer would heat for one heating cycle but no gas afterward. Ignitor would glow.
10 of 12 people found this instruction helpful.
  • Jim from Foothill Ranch, CA
  • Easy
  • 15 - 30 mins
  • Screw drivers
Checked four thermocouples all showed continuity with my multimeter so they were all good. I'd read that the coils commonly went out and that these were the symptoms. Hey, it's very simple in there. Not much else could be wrong. I had a Maytag repairman come out. At first he said the problem was a blocked vent. I knew he was wrong. Then h e said one of the thermocouples went out. It was $80 for him to come out. It turned out that his second diagnosis was wrong too. To repair the dryer by Maytag would have cost me $240. I gave him $80 and bought the coils for $37. They are EXTREMELY easy to replace: two screws held a bracket that held two coils. With the bracket off, I took off the old coils and slid on the new ones.
Was this helpful?
Thank you for voting!
Dryer squeeching very loud
9 of 9 people found this instruction helpful.
  • Michael from ENOLA, PA
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Socket set
Took off back of dryer Undid belt from belt adjuster pulled and took off adjuster put new one on redid belt and put back on dryer. Done
Was this helpful?
Thank you for voting!
latch on door broke
11 of 16 people found this instruction helpful.
  • donna from westmoreland, TN
  • Easy
  • Less than 15 mins
  • Pliers
very easily
Was this helpful?
Thank you for voting!
burnt out bulb and broken switch
12 of 19 people found this instruction helpful.
  • fanny from madison, WI
  • Easy
  • Less than 15 mins
  • Screw drivers
Both my husband and I are not good at DIY or fixing things. I watched the instruction video that was posted on the PartSelect web site. It seems easy to do it, however still very skeptical. My husband decided that there is nothing to lose in trying, so we ordered the parts. It is as easy and simple as the video instruction. We are very ha ppy customers.
Was this helpful?
Thank you for voting!
The main knob insert snapped.
11 of 16 people found this instruction helpful.
  • Larry from HICKORY, NC
  • Very Easy
  • Less than 15 mins
Nothing to it. Just remember to put the insert in the knob, NOT on the selector stem. Line up the flat part of the insert with the flat part of the stem and push the knob in place.

Don NOT ram it on the selector stem. When it's seated, don't push any more. That's all there is to it. It works. If the pointer on the knob indicat es the selector is lined up correctly, but it isn't, the problem is the selector, not the knob.
Was this helpful?
Thank you for voting!
The old door catch failed. Clothes won't dry with door open !
8 of 8 people found this instruction helpful.
  • Theresa from Norfolk, VA
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Old door catch came out, new one slipped in. All works great.
Was this helpful?
Thank you for voting!
No Heat
9 of 12 people found this instruction helpful.
  • NICHOLAS from PARMA, OH
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers, Wrench set
I suspected a faulty igniter and disconnected the cable to the igniter and measured the resistance of the igniter and found it to be 70 ohms then I checked the voltage at the same cable towards the power source and found it to be 25 volts ac which should be 120 volts ac. Next I checked the radiant flame sensor and found it to be open (i t should be a closed circuit when cold). I removed the flame sensor (with the power off) using a small box wrench and found a broken lead. Replacing the flame sensor solved the problem.
Was this helpful?
Thank you for voting!
My dryer made squeaking noise when rotating.
8 of 9 people found this instruction helpful.
  • James from KENNESAW, GA
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers
I followed directions found on several similar YouTube videos since the instructions included in the Whirlpool parts kit were not for my model dryer. I found that the original idler pulley was not rotating and the belt had worn a groove through it. I replaced all 4 roller wheels, idler pulley and the belt. Problem solved.
Was this helpful?
Thank you for voting!
Dryer Didn't Run
8 of 9 people found this instruction helpful.
  • William from Long Valley, NJ
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Unplugged washer,removed the two screws by the lint trap,moved the top foward lifted the top (it'shinged in the back )the switch is right inside the door top right hand corner removed the two screws that hold the switch in place used a flatblade screwdriver to seperate the connections pulled off the old installed the new switch put every thing back together worked as though it wes never broken
Was this helpful?
Thank you for voting!
The seal came off our dryer door.
10 of 15 people found this instruction helpful.
  • Janet from LOS ANGELES, CA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Take door off dryer (unscrew four screws). Lay door on flat surface. Using glue provided glue down new seal. Put dryer door back on and you're done!
Was this helpful?
Thank you for voting!
dryer would not heat or turn off
9 of 12 people found this instruction helpful.
  • michael from eldridge, IA
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set, Wrench (Adjustable)
removed front of dryer located igniter removed two screws disconnected wires then put new one in also replace thermal fuse and thermostat on back of dryer works great.
Was this helpful?
Thank you for voting!
All Instructions for the 110780
121 - 135 of 1248