110780 Kenmore Dryer - Instructions

All Instructions for the 110780
106 - 120 of 1248

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer door switch
12 of 13 people found this instruction helpful.
  • Frank from STANFORDVILLE, NY
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
We watched the video on ur website! Thank you
Was this helpful?
Thank you for voting!
The Dryer would not get hot.
14 of 20 people found this instruction helpful.
  • Jerry from Bradenton, FL
  • Really Easy
  • Less than 15 mins
  • Nutdriver
I removed the two screws holding the access panel, and removed the access panel. Then removed the lower air duct. I then checked the burner, The solenoid was not opeing the valve for the gas. I order the coils, in two day I had the coils and installed them. The dryer is working great.
Was this helpful?
Thank you for voting!
Door latch (female part) was broken.
11 of 11 people found this instruction helpful.
  • JEANMARIE from BELLEROSE, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I used a screwdriver to remove the old part and pushed the new part in with my fingers, it was very easy. If I could do it, anyone can. I was a lot cheaper then having a repair man come to house. I am very glad I found your site online, I will definitely be using your company again.
Was this helpful?
Thank you for voting!
The dryer was not fully drying
12 of 14 people found this instruction helpful.
  • Michael from Chicago, IL
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Socket set
After replaceing several parts including the thermostats the last part I replaced the coils were the defective part. I originally metered out the themostats and they appeared to be okay but since this was my first time I thought I might have been mistaken. It turns out the last part I thought it could be was the part that was defective. I will say that it is very simple to replace any of the parts involved. The hardest part was trying to open the dryer itself. But after having to do it 3 times, I'm now a pro. I also replaced the drum belt and since I had it open I also replaced the belf idler with a newer modified idler rolller.

Putting the belt back on is easy, but it helps to view the video or a picture to understand how the belt goes around it.
Was this helpful?
Thank you for voting!
dryer not heating up
12 of 14 people found this instruction helpful.
  • Richard from New Windsor, NY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Unscrewed 4 screws,pulled off front of machine.Unscrewed 2 screws holding coils on,unplugged coils,installed new coils,plugged in coils,reinstalled 2 screws for hold down brace.Reinstalled front cover,plugged dryer into outlet(remember to unplugged dryer before working on it).started up,instant heat,works great.thanks Partselect for helpi ng me out!!!
Was this helpful?
Thank you for voting!
Rear dryer drum seal came out
17 of 29 people found this instruction helpful.
  • William from Pontiac, MO
  • Easy
  • More than 2 hours
  • Screw drivers, Socket set
Used my Whirlpool Dryer User Instructions Manual and followed instructions and used the Cabinet Parts page to see the diagrams.
Was this helpful?
Thank you for voting!
Scratches in Surface
83 of 228 people found this instruction helpful.
  • Michelle from Richardson, TX
  • Really Easy
  • Less than 15 mins
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this helpful?
Thank you for voting!
When using the dryer the cycle would stop and display E1 as the reason
13 of 18 people found this instruction helpful.
  • Joyce from Holbrook, NY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Unscrewed the bottom panelof the dryer and located the thermistor through the schematic for my machine. Removed the old one and put the new one in the same way. No more E1 problems and all cycles now complete themselves.
Was this helpful?
Thank you for voting!
squeaking sound due to worn out bearing idler pulley wheel.
13 of 18 people found this instruction helpful.
  • Evan from NORTHRIDGE, CA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
BEFORE ANYTHING ELSE UNPLUG THE POWER AND TURN OFF THE GAS SUPPLY 1. unscrew the 3 nut screws at the back to remove the cover lid. 2. pull the control console cable from the electronic board. (only 3 wires on it).3. unscrew the 2 nut scr ews of the control console then remove it by pulling up.4. unscrew the 5 screws to remove the door. (pull little up to unhinged then remove). 6. unscrew the 5 nut screws to remove the lower siding. 7. unscrew the copper 4 nut screws then remove the lint suction fixture 8. unscrew the 4 nut screws to remove door fixture ,then just lay next to the machine.(the wires are long enough so you don't need to unplug and separate it from the machine.9. remove the belt by pulling the idler pulley towards the motor pulley (against the tension spring) 10. remove the drum by lifting a little bit upward. 11. remove the plastic triangular lock using a small screw driver then remove the idler pulley wheel then install the replacement. (clean your machine using a vacuum cleaner and remove all the lints). 12. install back the drum, be sure to set the drum belt to the right position. (groove on drum side). 13. install back the belt to the pulley the same procedure as to remove it. 14. assemble back what you have removed. end.
Was this helpful?
Thank you for voting!
dryer would not turn off when the door is open
10 of 10 people found this instruction helpful.
  • James from Webster, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
it took loess than 10 minutes to change the door switch after watching the repair video
Was this helpful?
Thank you for voting!
Dryer Would Not Start.
11 of 13 people found this instruction helpful.
  • GALEN from NEDERLAND, TX
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Partselect order confirmation email included video instructions of how to change the door switch on my model dryer. Like others I had a pause with the switch connector. I viewed the video again and the instrucions showed to use the putty knife tip to push down on the connector tabs and it came right off. Replacing the switch was easy a s the video instructions. Fast shipping of the right part at a good price. The video was pricless. Thank you partselect.
Was this helpful?
Thank you for voting!
Idler pulley wore out
10 of 11 people found this instruction helpful.
  • Peter from HUEYTOWN, AL
  • Very Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Removed the back panel and saw that the idler pulley was worn out. It only took me 5min. To replace, it was very easy to replace.
Was this helpful?
Thank you for voting!
Door switch was broken
11 of 14 people found this instruction helpful.
  • Anthony from Orlando, FL
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
I typed in on my brouser Repair Kitchen Aid Dryer door switch.
And on You Tube up came several videos showing me how to ewmove the switch and install the new one.

The hardest part of the job was not instaling the switch but the dryer Vent hose from the back of the dryer after I puled it away fro m the wall, it disconnected and the I had to Pull the Washer out which was right next to it so I could put the vent hose back to the dyer. I has to disconnect the Hot/cold water line pull the washer out connect the dyer hose reconnect the cold /hot water lines and yada yada yada
Was this helpful?
Thank you for voting!
would not stop when opening door during cycle
10 of 11 people found this instruction helpful.
  • PHILIP from MATTHEWS, NC
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Found a U tube video to be useful. Remover 2 screws under the filter lid. Used a putty knife blabe wrapped in masking tape to unclip the lid. 2 screws to remove the switch. Biggest difficulty is seperating the electric connector. installed replacement switch and closed lid.....reality is this is a 15 minute repair. The extra time was to take the time to remove dust and lint from behind the dryer. Easy repair.
Was this helpful?
Thank you for voting!
Broken belt. Broken idle pully and replace 4 rollers
11 of 14 people found this instruction helpful.
  • Mike from INOLA, OK
  • Easy
  • More than 2 hours
  • Nutdriver, Screw drivers, Socket set
By watching the video it made the job much easier than I thought it would be. I was very pleased with the speedy delivery of the Dryer kit I had ordered. I had called a local repair facility and they wanted twice as much for the same parts.
Was this helpful?
Thank you for voting!
All Instructions for the 110780
106 - 120 of 1248