110773 Kenmore - Instructions

All Instructions for the 110773
106 - 120 of 2350

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
soap dispenser door/spring broken
30 of 54 people found this instruction helpful.
  • KEVIN from PLAINFIELD, IL
  • Easy
  • 15 - 30 mins
  • Screw drivers
removed old parts and re-installed new parts. The spring is a little hard to get to the right point without a jewelers screwdriver, after that everything worked fine.
Was this helpful?
Thank you for voting!
Dishwasher would not fill with water.
21 of 27 people found this instruction helpful.
  • Robert from Waldoboro, ME
  • Really Easy
  • 15 - 30 mins
  • Wrench (Adjustable)
After doing some research in a repair book I decided to take a stab with a water inlet valve. With expedited shipping I ordered the part and within three days it was delivered. I installed it and the dishwasher seemed like it was trying to fill but still would not. After much cocnsternation I turned the water supply valve to the dishwash er a partial turn to close and I felt the water rush through the valve and the dishwasher then filled. Apparently the shut off valve must have been clogged plus it now leaked. I then replaced the shutoff valve and the copper pipe to the water inlet valve with flexible 3/8" tubing and the dishwasher thus far is running fine without leaks.
Was this helpful?
Thank you for voting!
Detergent Cup does not open
26 of 42 people found this instruction helpful.
  • stephen from venice, FL
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Disconnect power supply to dishwasher. Open door and remove screws on inner door cover. Carefully remove inner cover while watching how inner parts are arranged. Found return spring on detergent cup linkage had rusted and broken causing detergent cup not to open. Installed new spring and re assembled inner cover. Rotated timer dial one fu ll revolution to check operation of detergent cup. Worked like a charm. Re connect power supply to dishwasher and your good to go.
Was this helpful?
Thank you for voting!
How to un-screw the blower fan!
19 of 21 people found this instruction helpful.
  • Tim from Fremont, MI
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Wrench (Adjustable), Wrench set
The dryer motor quit working. Learned, if you are changing one that is old, get the blower wheel fan too! I could not break mine loose from the motor shaft, and had to bust it off.

To un-screw the blower wheel fan from the motor shaft: from the front of the dryer, grab the plastic fan on the back of the motor with an adjusta ble wrench, and the motor shaft on the front of the motor with vice grips. Turn the motor shaft CLOCKWISE holding the fan still to un-screw the fan. If you have to remove the pulley, grab the shaft and turn the pulley COUNTERCLOCKWISE with a wrench.

Just make sure to pay attention to the orientation of the new motor in the instructions. If you match the old motor, it will not fit. It is all spelled out in the directions.
Was this helpful?
Thank you for voting!
Heat Would Not Come On
20 of 24 people found this instruction helpful.
  • Lynn from Novi, MI
  • Really Easy
  • Less than 15 mins
  • Nutdriver
After replacing all the other fuses and sensors I finally replaced the Radiant Flame Sensor and it is working perfectly.

After replacing the other parts and the heat still not coming on I read somewhere that the Radiant Flame Sensor is a normal closed circuit and when I checked with a meter it was open. I would have saved a lo t of time and money if I had read that earlier.
Was this helpful?
Thank you for voting!
Replaced belt while I was in there replacing motor
20 of 24 people found this instruction helpful.
  • Douglas from COMMERCE, TX
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable)
If you were to do the Belt Replacement only, here is the quick synopsis:
1. Unplug dryer;
2a. Open lint door on top of dryer and remove the two phillips head screws that hold the lint bay to the metal dryer top;
2b. Next remove the two brakets holding the metal top to the dryer back (one screw on each bracket);
3. Use a flat-blade screw driver to pry off the top of the dryer (leaving the timer and start button area attached);
4. Lift off top and push back to expose just enough area so you can get to the two screws holding the dryer sides to the dryer front;
5. Unplug door switch;
6. Unscrew screws from #4;
7. With door open, lift dryer front (only about an inch) and then pry bottom of dryer front from dryer sides. The bottom of the dryer front is not screwed, just siting on Front Panel Clips;
8. Once the front is off the dryer, simply remove the belt and install the new one. Please note that while you are in here, you may want to inspect the rear drum seal and replace if it is worn to the point where metal is rubbing on metal. This is also a good time to clean out dust from inside this cavity to help extend the life of the bearings on the rollers and prevent dust from accumulating and gunking up the motor, etc.
9. Re-assemble tin the opposite order.
If you have any mechanical sense at all and you don't know anything about dryers, you will be surprised at the simplicity of the dryer.
Was this helpful?
Thank you for voting!
Top Spray Arm was hitting and would not rotate properly
20 of 25 people found this instruction helpful.
  • Richard from Buda, TX
  • Easy
  • 15 - 30 mins
  • Screw drivers, Wrench set
The mounting bracket was broken.

The parts ordered were a direct match due to the fantastic pictures supplied on this site.
A dealer wanted to order it and then I would have had to drive and pick it up - no way.

partselect.com first time user - very easy.
Was this helpful?
Thank you for voting!
Motor would not turn
21 of 28 people found this instruction helpful.
  • Christopher from bellerose, NY
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
1) Removed top of dryer
2) removed belt and drum
3) removed front of dryer
4) popped clips holding down motor
5) unscrewed rear fan from motor (by exposing and holding fan)
6) changed motor
7) changed support rollers and idler pully
8) reassemled dryer
Was this helpful?
Thank you for voting!
it would turn off and on mid-cycle and finally quit completely
20 of 26 people found this instruction helpful.
  • Nat from Raleigh, NC
  • Easy
  • 15 - 30 mins
  • Screw drivers
I turned off the circuit. I removed the interior side of the door and then the plastic covering over the electrical wires and switches (I counterbalanced the door with a couple of half gallon juice containers). I removed the wires attached to the switch on the door handle and the door handle itself. The handle and switch parts disassem bled and I replaced the switches (part of kit). I cut off the singed wire and the other three beyond the damaged portion and stripped the wires and connected the extensions (part of kit). I attached the new wires to the switches and closed up the interior door. Lastly, I turned the circuit breaker back on. All was well!
Was this helpful?
Thank you for voting!
Water dripped out from the bottom of door.
25 of 41 people found this instruction helpful.
  • Louis from Niceville, FL
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
Diagnosing the problem, i.e. finding the source of the leak, was the hardest part. The best clue was the leak only occurred well into the cycle when the water was hot and steam was coming out the vent. I then assumed there was a bad seal and steam & condensed water was leaking down into the door. I replaced the vent duct & seal, a broken drip cover (an internal part in the door), and replaced a missing rinse aid cap. This stopped the leak.
Was this helpful?
Thank you for voting!
Drum was binding because of worn bearing supporting front of dryer drum
23 of 35 people found this instruction helpful.
  • Leslie from Townsend, GA
  • Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
First I unplugged the dryer for safety, then I removed the top of the dryer, then removed the 2 hex head screws holding the font door panel onto the dryer. Then I disconnected the door safety switch. the rest was cake. I removed the old bearing and cut the new bearing and seal to the exact size of the old one. I used contact cement to gl ue the new bearing and seal into place. Reassembly was a breeze. End of job. Success!!!
Was this helpful?
Thank you for voting!
dryer worked but no heat
18 of 20 people found this instruction helpful.
  • Tracie from Culver City, CA
  • A Bit Difficult
  • 15 - 30 mins
Initially we thought the problem was the igniter, so we ordered an igniter kit. Installed it but was unsuccessful. We then went on the websight and read further, about 50% of dryers with no heat but working had a problem with the thermal fuse.So we ordered the thermal fuse installed it, which was very easy, and success. Once the problem was diagnosed properly it was fast and easy. Recommend looking at the statistics for specific problem.
Was this helpful?
Thank you for voting!
Replaced two parts in the gas heater assembly
20 of 26 people found this instruction helpful.
  • L R from Carmel, NY
  • Easy
  • 15 - 30 mins
  • Screw drivers
I removed the front panel of the dryer by removing the 2 screw that secure it at the bottom and pulling upward to disconnect the cover at the top. I then removed the two screws that hold the metal cover that secures the 2 elements in place. I disconnected the wire plugs from the 2 elements, removed the 2 elements and replaced them with th e new parts making sure to place them in the same positions as before. I then replaced the housing cover and tightened the screws. Then I replaced the front cover of the dryer.
Was this helpful?
Thank you for voting!
Got heat only on start of cycle and no repeat of flame. Suspected coils on gas valve.
18 of 20 people found this instruction helpful.
  • John T Lundy from Pittsburgh, PA
  • Really Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers, Wrench set
I used a multi meter to find coils failed in warmed temperature condition.
I tested main switch for different cycle operation. Main switch was worn out inside and not making good contact for soft cycles.
This dryer is 25 years old. I chose to replace all the sensors, fuses, ignitor, gas valve coils, cycle switch and thermostat.
This was cost effective for me, because now, I actually have a good dryer that might just last another 25 years. I might replace the drive belt soon. I'll order from Parts Select. This was easy and fun. Thanks!
Was this helpful?
Thank you for voting!
Dishwasher Rehab
18 of 21 people found this instruction helpful.
  • John from Manchester, CT
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set, Wrench (Adjustable)
After hearing ominous grinding sounds and water leaking around the gasket, it was about time to rehab the dishwasher. This is usually the point where I say "t'hell with it, buy a new one". I am glad I didn't.
The Kit to rehab the impeller and such had EVERYTHING I needed. Right parts, right price.
Removed the upper arm assembly, T15 screwdriver, the screen strainer, the impeller, T25 screwdriver, the food grinding spring and impeller (the grinding noise, spring was sprung), and finally the post and impeller thingie (had to break it off, very brittle). The pieces went back on a lot more smoothly than it took to get them off!
Use your digital camera! I took pictures of every stage of the parts removal and what I removed. I got confused with some little balls that were inside and the pictures told me exactly where they went.
Door gasket? I should have replaced it YEARS ago, so easy and cheap with PartSelect parts.
Was this helpful?
Thank you for voting!
All Instructions for the 110773
106 - 120 of 2350