110773 Kenmore - Instructions

All Instructions for the 110773
76 - 90 of 2350

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
My dryer only heats up at the beginning of cycle so my clothes will not dry.
31 of 39 people found this instruction helpful.
  • Monique from Mission Viejo, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
I remove the front control panel and to get to the bottom front dryer door off. Using my volt meter i checked all the sensors and thermal. I surf the internet for hint and some one mention to replace the coil since some time you could have one goes out and the other working still. After i replaced the coil kit it works like a champ.
Was this helpful?
Thank you for voting!
no heat
31 of 40 people found this instruction helpful.
  • rex from streator, IL
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Wrench (Adjustable)
the ignitor did not glow red checked thermal fuse by exhaust duct. fuse open replaced thermal fuse
Was this helpful?
Thank you for voting!
Dyer drum doesnt turn
27 of 29 people found this instruction helpful.
  • Shawn from Akron, OH
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
It was really quite esy remove the screws from the back and pop the top off . then remove 2 top inside screws from the front , lift the front off the sides , support the drum and lift out , you will then see the idler wheels, replace them with the new ones ,replce the tensioner , wrap the belt around the drum, need help putting the drum b ack in the case, have someone hold the drum in place while you lay on the ground and put the belt around the motor pulley and the tensioner on the bottom.you then put the front panel back into place and secure with the 2 inside screws, then put the rest back together in reverse oder. ... hope this helps someone
Was this helpful?
Thank you for voting!
Dryer would dry for 5-10 minuets then no heat
35 of 55 people found this instruction helpful.
  • Richard from Jerome, MI
  • Easy
  • Less than 15 mins
  • Screw drivers, Socket set
I tested the dryer coils and found that they were getting a voltage but would not open the gas valve. Coils were not bad but weak. After they warmed up they would not open the gas valve. It took 10 min to repace both coils and the heat sensor.
Was this helpful?
Thank you for voting!
had to replace the motor
31 of 43 people found this instruction helpful.
  • charles from parker, CO
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Screw drivers
Follow the advice given in the partsselect website. However, while removing the blower, my hand slipped into the housing and cut my thumb. Connected the wires to the junction box on the motor but didn't realize that the contacts would hit the drum when reinstalled. The original junction box was at a 90 degree rotation relative to the n ew box. When trying to test the breaker tripped. Using the multitester I found out that I burned out the thermal fuse, and froze the door switch. I replace both those parts and started the dryer and could hear a grinding sound. Inspection revealed that the housing of the motor was rubbing against the drum. Removing the drum yet again, I rotated the housing and replaced the drum. The dryer was finally working well.
Was this helpful?
Thank you for voting!
The dryer belt broke. During the effort to replace the belt it was noted that the lint trap housing seals were in need of replacement.
27 of 31 people found this instruction helpful.
  • Benjamin from WELLS, ME
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver
With the dryer taken apart to replace the broken belt it was obvious that the lint seals had not been working properly due to the excessive amount of lint covering all of the inside surfaces of the dryer. The belt idler pully had also moved from its normal mounting position and was laying at the bottom of the dryer. Because the lint had c overed the bottom before the belt broke it was obvious to determine where the idler pully attached to the bottom.

Before cleaning I marked the exact location where the idler pully mounted to the bottom of the dryer.

While waiting for the replacement parts to be delivered a vacuum cleaner was used to remove lint from the inside surfaces of the dryer as well as the old fragments of the lint trap housing seals were removed and surfaces where the new seals would attach were cleaned.

Assembling the dryer with the new belt was a challenge due to the lack of support for the drum while getting the new belt in place, lined up properly, threaded through the idler pully and attached to the motor drive shaft. This is how I installed the new belt:

I used a piece of wood wider than the sides of the dryer, drilled holes that allowed for a piece of cloths line rope to be looped through and used to support the door opening end of the drum.

The drum was set on the seal and rollers at the back of the dryer.

The temporary wood /rope hanger was placed at the front end of the dryer resting on the sides with the top of the dryer raised.

The rope was adjusted until the drum rested on the back rollers and the rope like it would be positioned normally.

The new belt was then gently installed under the temporary support rope and around the drum.

The new belt had many kinks from shipping and was difficult to align with the location on the drum where it needs to ride so small strips of tape were temporarily used to hold the new belt in position until it could be fed through the idler pully and on to the drive shaft.

Several small pieces of a cardboard box were used to shim under the idler pully to hold it in its proper location as well as to make the belt attachment to the drive shaft easier.

With the belt attached, the temporary cardboard shims were removed from under the idler pully.

The front of the dryer was attached .

The temporary board and rope hanger was removed.

The tape that had been placed over the new belt to hold it in proper alignment was removed as the drum was rotated slowly by hand to ensure that all tape was removed prior to closing the top of the dryer.

The seals as well as the remainder of the dryer assembly was completed without any problems.

The dryer ran well for its initial trial spin and has dried several loads of laundry since.

Great parts and support Thankyou
Was this helpful?
Thank you for voting!
Dryer would not tumble.
25 of 26 people found this instruction helpful.
  • John from Minneapolis, MN
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
I wasn't sure if the problem was the belt (probable) or the idler pulley assembly (less likely) but the total for both parts was about $26 plus shipping. So why not replace both to be sure?

As it turns out, my original idler pulley assembly does not turn. Rather, it has a concave semi-circular piece that is fixed in place. T he belt ran in a groove in that piece.

The replacement part has a nylon wheel that turns. As a result of replacing the idler pulley assembly (which I don't think was necessary to fix my tumbling problem) the dryer runs much quieter. (We used to get a fair amount of squeaking when the belt rubbed).

As for the actual repair (I would rate myself as above average on tackling household repairs), it was about the simplest repair I've ever done. I followed the video provided on this site (excellent video) and it took less than 20 minutes -- cleaning up all of the lint/odds and ends under the washer and dryer took longer than the actual repair.

My only issue (minor) was disconnecting the electric harness. It did not slide as easily as in the video. I had to coax mine a bit with a small screwdriver (make sure your dryer is unplugged!!). I suspect it was simply a function of the harness never being unplugged -- the dryer is 9 years old.

I also felt great because I'm sure I saved a $125 service call (for only $26 in parts and 20 minutes of my life).

Good luck!
Was this helpful?
Thank you for voting!
Dryer would not heat up.
26 of 30 people found this instruction helpful.
  • Roger from Bonners Ferry, ID
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
I unplugged the dryer,removed the two small screws on the front of the dryer and pulled the bottom forward. The two wires connected to the door do not have to be removed. With an electrical tester using the Ohm setting I tested the Radiant sensor and the Gas Valve coils. The two terminal coil was DOA. The dryer can be operated with the f ront open as long as the door wires are connected. Symptons: The igniter would heat up and not release gas. My repair was successfull due to this awesome website and the super fast shipping service. AAAA++++
Was this helpful?
Thank you for voting!
Poor wash quality and excessive noise
31 of 45 people found this instruction helpful.
  • Michael from Stuart, FL
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
I inspected the pump and checked on-line for instructions . I removed the lower panel and the lower dish rack . Removed the washer head from the top of the pump inside the dishwasher . I next unplugged the wiring after disconnectiong the power supply . Next step was to remove the drain hose from the bottom of the pump . Put a towel under it because it's full of water . Unscrew the nipple from the bottom of the pump to allow clearance so it may be removed thru the top . There are four plastic ears that rotate on the base of the pump . Move them into the outboard position and lift the pump out thru the top. I applied some liquid detergent where the pump seal goes and pushed it back in . Installation is the reverse of removal .
Was this helpful?
Thank you for voting!
Dishes not rinsing well, particles left on dishes
26 of 30 people found this instruction helpful.
  • Steven from Missoula, MT
  • Really Easy
  • Less than 15 mins
  • Wrench (Adjustable)
As others have described, this replacement was very easy. The new spray arm is solid plastic instead of rubber (which had deteriorated and was the part that needed replacing). So it should last longer.

You have to keep and reuse the mounting bracket that attaches the spray arm to the upper rack, so don't throw that away!
< br />The replacement was super-easy, and as others have commented, the dishes haven't been this clean for a long time. Well worth it.
Was this helpful?
Thank you for voting!
Dishwasher not cleaning well... then leaking
29 of 39 people found this instruction helpful.
  • Wesley from Lake Elmo, MN
  • A Bit Difficult
  • 1- 2 hours
  • Screw drivers
This gets a little lengthy... but it explains where Cascade Dishwashing Powder came up with its brand name - it's been a cascade project.
I started by replacing the Middle Wash Arm Tube as the old tube developed leaks. As others have stated this is a new design but directly replaceable and easy to do.
This didn't solve the clean ing issue so reading the experiences of others on this site realized I also had broken parts in the Upper Spray Arm Assembly and the Upper Wash assembly. I replaced these and the dishes were suddenly much, much cleaner. These were very easily replaced.
I did find that I did not need the Mount for the upper spray arm (PS402277) as a redesign of the Upper Spray Arm Mounting bracket no longer required it - the bracket simply clipped in -the diagram was out of date.
Everything seemed to go well for about 3 loads when the dishwasher started leaking heavily out of the bottom of the door. I then noticed that the lower Wash Arm Bearing Ring and the Seal, Lower Spray Arm had disintegrated so I replaced those but this didn't affect the leaking. Someone had stated that if the lower wash arm assembly had too much 'wobble' that it cause 'waves' that would leak out the front door... mine had some wobble so I added a nylon washer from Ace Hardware that reduced wobble but still leaked.
I then replaced the Door Seal Kit - this was by far the most difficult part as the door needed to be removed and it was somewhat difficult - and it seemed apparent after we had removed the door that these parts weren't the problem but we replaced them anyway.
Also, someone else had noted that they had to attach the door seal (this is NOT the gasket that goes around the door opening) with a sealant - I had the same problem; the original seal fit tightly with friction but the new replacement required an adhesive - I used silicone. Still leaked.
From here on I can't guaratee any useful information: I took the strainer screen out of the bottom of the dishwasher and found one slightly loose screw holding what I believe is the 'pump outlet' according to the diagram. I had also read that the water fill is controlled not by the float at the bottom of the washer but by the electronics and it was suggested that I disconnect the DW from the power to 'reset' the timer, this I did and hit the 'Cancel' cycle a couple of times to make sure that all programs were cancelled. Whether any of this made a difference I have no idea - except that the dishwasher suddenly stopped leaking and hasn't leaked a drop for at least 20 washes. So I don't know, for sure, why it leaked or how I fixed it, but it's working and washing great now - except the tines on the lower rack are beginning to rust out and breaking off. The rack is pretty expensive but so far I've saved a lot of money and my family thinks I'm a dishwasher genius.
Was this helpful?
Thank you for voting!
Drayer Was Making Squeaking Sound
26 of 30 people found this instruction helpful.
  • Charles from Gray, TN
  • Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
Took off the top and front panel. Found that the belt tensioner was worn out. Decided to pull drum out,and replace the belt and drum rollers also. Put it back together, and it works fine.
Was this helpful?
Thank you for voting!
The lint filter was seriously damaged
26 of 31 people found this instruction helpful.
  • Katharine from Palm Springs, CA
  • Really Easy
  • Less than 15 mins
After the new filter arrived, I took the old filter out, put the newe one in. No tools, no difficulty at all. Actually, the really difficult part of this entire episode was finding the model number on the dryer. It was on the underside of the door.
Was this helpful?
Thank you for voting!
Dishwasher stopped in middle of wash cycle..
29 of 42 people found this instruction helpful.
  • David from Bay City, TX
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
I disasembled the inner door and replaced the door switches with new ones.
Was this helpful?
Thank you for voting!
The dryer was making a squeaking sound when running
24 of 27 people found this instruction helpful.
  • David from PATASKALA, OH
  • Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
Installation went very well. Raised the top of the dryer, removed the front of the dryer, remove the drum, at this point the dryer‘s wide open removed the police and the tensioner also remove your tire rings replace everything back in order as how are you get apart. Repair took about an hour and 15 minutes
Was this helpful?
Thank you for voting!
All Instructions for the 110773
76 - 90 of 2350