110773 Kenmore - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The upper arm mount broke off and needed to be replaced.
51 of 52 people
found this instruction helpful.
-
George from McKinney, TX
- A Bit Difficult
- Less than 15 mins
The part arrived the next day after order was placed. That is an amazing service.
When it arrived I noticed that the new part was re-designed but the dimensions appeared to be identical. Initially it was difficult to snap it in to position but with help of a screw driver it finally snapped in place. After re-installation of the upp ... Read more er wash arm all looked perfect. But the arm would not spin freely. It would bind against the bottom of the upper tray. Finally after about 20 minutes I noticed that the mount was slightly slanted to one side. This was not immediately apparent unless you look carefully. Further I noticed that the bottom of the upper tray was protruding lower on the right side. Finally I realized why the mount was slanted to one side. I removed the mount and turned it 180 deg.. Bingo all fits and works perfectly. I could have avoided the problems if an orientation directions were included with the mount. I suspect that a less technical individual would likely not figure it out.
When it arrived I noticed that the new part was re-designed but the dimensions appeared to be identical. Initially it was difficult to snap it in to position but with help of a screw driver it finally snapped in place. After re-installation of the upp ... Read more er wash arm all looked perfect. But the arm would not spin freely. It would bind against the bottom of the upper tray. Finally after about 20 minutes I noticed that the mount was slightly slanted to one side. This was not immediately apparent unless you look carefully. Further I noticed that the bottom of the upper tray was protruding lower on the right side. Finally I realized why the mount was slanted to one side. I removed the mount and turned it 180 deg.. Bingo all fits and works perfectly. I could have avoided the problems if an orientation directions were included with the mount. I suspect that a less technical individual would likely not figure it out.
Read less
Was this helpful?
Thank you for voting!
dryer would get hot for a while, then quit heating
56 of 70 people
found this instruction helpful.
-
Sharon from Houston, TX
- Easy
- 15 - 30 mins
-
Screw drivers
After reading about other people with this same problem I took a chance that this would be what was wrong with my dryer.I took off the front cover of the dryer by removing two screws. I located the faulty coils and simply plugged in the 2 new coils Tah-dah Probably coud have been done without even removing the front panel, but since it
... Read more
was off I vacuumed out the lint ( actually my husband did all of the above, but I tell a better tale than he does and I diagnosed the problem and ordered theparts)
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
the dryer only blew cold air
48 of 52 people
found this instruction helpful.
-
charles from waukesha, WI
- Really Easy
- 15 - 30 mins
-
Nutdriver
actually i found your site before i even looked at the dryer,thats how i knew to check for the thermal fuse.
I ordered the part and it was on my door in 36
hours,pulled the two wires off the old fuse and installed the new,put the back cover on and it has been working ever since,thanks ( your in my bookmarks)
I ordered the part and it was on my door in 36
hours,pulled the two wires off the old fuse and installed the new,put the back cover on and it has been working ever since,thanks ( your in my bookmarks)
Was this helpful?
Thank you for voting!
Top Water Tube hose broken.
43 of 44 people
found this instruction helpful.
-
Cathy from SANDY, UT
- Really Easy
- Less than 15 mins
-
Screw drivers
The part came so fast without extra shipping. It took only 10 minutes to replace water tube and upper spray arm. I only had to remove one screw. Replaced with new parts and reinstalled screw. It was easier and cheaper than calling a repairman.
Was this helpful?
Thank you for voting!
Dryer motor would not turn on
51 of 69 people
found this instruction helpful.
-
John from Bluffton, SC
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Wrench set
After looking at the schematic to see what was in line with the motor, I found the fuse as the first item. I pulled the fuse out and used a multimeter to ohm out the fuse. Upon using the meter I found that the fuse was bad. I typed into Google my part number that was on the fuse and the PartSelect Website came up as one of the choices to
... Read more
pick from. When the part arrived approx. two days later I installed the fuse by first unplugging the dryer and then removing the bottom panel and removing the fuse from the exhaust by using a small 1/4 inch wrench and pulling out the old fuse. I installed the wires on the new fuse and re-installed and put the 1/4 inch screw back in. I started the dryer after plugging it back in and it worked like it should have. Thank you for the part and I have recommended your website to other people already.
Read less
Was this helpful?
Thank you for voting!
Gas Flame Would Drop Out
49 of 66 people
found this instruction helpful.
-
FRED from BRIELLE, NJ
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers
First it was a process of alimination to find out why it was dropping out. After the problem was found it was just a matter of replacing the holding coil on the gas valve. Thank you fred kenney sr
Was this helpful?
Thank you for voting!
No power
45 of 55 people
found this instruction helpful.
-
Nick from Brandon, FL
- Easy
- 1- 2 hours
-
Nutdriver
My 14 year old son did it as I supervised! Pulled the dryer out on a dolly, unpluged the dyer, removed 9 hex head screws to remove the back cover, removed and replaced the thermal fuse, located next to the exhust outlet, set the cover back on, moved the dryer back in with the dolly. I had the thermal fuse over nighted to me for a total
... Read more
price of $35, figured I saved at least $150 on a service call by Whirpool.
Read less
Was this helpful?
Thank you for voting!
Intermittent or no gas ignition, HSI ignightor working
43 of 50 people
found this instruction helpful.
-
Steven from Sauk Village, IL
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Removed front of gas dryer and cleaned all lint out. Checked HSI, and cleaned flame sensor. Split (3 terminal) gas coil terminals were intermittent. Read about 700 ohms across outer two terminals, but center terminal to either outer terminal was open (Infiniti on meter) 2 terminal coil measured about 550 ohms. 3 terminal coil should read
... Read more
about 700 ohms across outer terminals, and about 1.5K ohms center to outer terminals. Unscrewed index cover plate and replaced coil, 2 terminal coil was okay. Reassembled and finished 12 loads of laundry no problems at all.
Read less
Was this helpful?
Thank you for voting!
Busted Belt & Pulley
43 of 51 people
found this instruction helpful.
-
James from West Haven, CT
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I bought a belt from a store in my area- What a mistake...I found this site and read all the stories on how easy it was and how PartSelect.com had the parts in stock and had easy instructions...I put the idler pulley in place, put the belt in place (all from instructions included) and put the dryer back together (which was easy). I actua
... Read more
lly did it alone. I would recommend this company to anyone in need of their parts and help!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
The old rack was rusty leaving stains on our china
41 of 46 people
found this instruction helpful.
-
Carol from Richmond Hill, GA
- Really Easy
- Less than 15 mins
-
Screw drivers
The new rack came with four parts... those four parts were the wheels that the rack rides on to slide it into the dishwasher. You will need to recycle two rubber bumpers, your old utensil basket and the cone in the center of the rack. Getting the cone free was not easy. It has to be rotated to release it from the wire rack. I had to pry i
... Read more
t free with a screwdriver. Once rotated it lifted out easily. I noted how the cone lined up in the old rack and installed it the same way in the new rack. It was much easier to install than remove. The new rack has a gray tinge to it but fits perfectly and we are pleased with the end result.
Read less
Was this helpful?
Thank you for voting!
Dryer would not shut off on auto dry settings
42 of 50 people
found this instruction helpful.
-
Wiliam from Belleville, MI
- Really Easy
- 15 - 30 mins
-
Nutdriver
I removed the discharge duct from the back of the dryer. Then, I removed the screws on the back of the dryer and the back itself. This exposed the cycling thermostat. I removed the screw holding the thermostat. I took the wires off the defective thermostat and reinstalled them on the new thermostat. Then, I reassembled in reverse order.
Was this helpful?
Thank you for voting!
Water leaking out under door
39 of 42 people
found this instruction helpful.
-
Charles from Brooklyn, NY
- Easy
- 15 - 30 mins
The pump outlet gasket was sticking out and a screw was missing from the pump outlet housing. This was causing water to flood out under the door.
Once I removed the pump outlet housing I saw that the gasket was out of place almost all the way around. I cleaned around the housing, replaced the gasket and the missing screw.
... Read more
You need a Torx T-15 for this repair. Note that all of the screws on the housing were loose so you might need to tighten them from time to time.
Be careful not to drip a screw when you are installing it since it's a real hassle to fish it out from under the screen.
Once everything was tightened up, the wash pressure seemed to be much higher.
Once I removed the pump outlet housing I saw that the gasket was out of place almost all the way around. I cleaned around the housing, replaced the gasket and the missing screw.
... Read more
You need a Torx T-15 for this repair. Note that all of the screws on the housing were loose so you might need to tighten them from time to time.
Be careful not to drip a screw when you are installing it since it's a real hassle to fish it out from under the screen.
Once everything was tightened up, the wash pressure seemed to be much higher.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Inlet valve was leaking from crack in brass fitting
39 of 44 people
found this instruction helpful.
-
David from Lexington, NC
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Removed the lower panels from beneath the dishwasher door. 4 screws. Turned off the water.
Removed one screw holding the inlet valve to the side rail of the dishwasher. It was attached to the hot water line and then the washer water input line. Removed the electrical connector..Pull straight off, and use a pair of pliers to ... Read more open the squeeze clamp on the washer hose. The hot water supply hose has a brass fitting to loosen and remove.
Replaced the inlet valve, reconnected the electrical and also replaced the hot water line from under the sink to the washer. Used a new braided 5' hose with fittings. Used teflon tape on the screws and did not over tighten the brass fittings.
Turned on the hot water supply and checked for leaks. Operated the washer and checked for leaks. Replaced the lower covers.
Removed one screw holding the inlet valve to the side rail of the dishwasher. It was attached to the hot water line and then the washer water input line. Removed the electrical connector..Pull straight off, and use a pair of pliers to ... Read more open the squeeze clamp on the washer hose. The hot water supply hose has a brass fitting to loosen and remove.
Replaced the inlet valve, reconnected the electrical and also replaced the hot water line from under the sink to the washer. Used a new braided 5' hose with fittings. Used teflon tape on the screws and did not over tighten the brass fittings.
Turned on the hot water supply and checked for leaks. Operated the washer and checked for leaks. Replaced the lower covers.
Read less
Was this helpful?
Thank you for voting!
dryer makes a lot of noice, bad rolleres
37 of 40 people
found this instruction helpful.
-
Jesus E from Palm Bay, FL
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers
super fast shipping, got the part in two days, and had it done in 15-20 min, remove the front pannel, remove the belt and tenssioner,took the drum out , took the old rollers , lubed the shafts,replaced the old rollers with the new ones, intalled the drum back, the tenssioner and the new belt, reinstalled the front pannel, and done...easy
... Read more
and fast job, like new dryer, works nice...save some money...the new one will do the same..just dry the clothes.
Read less
Was this helpful?
Thank you for voting!
Gas burner would not ignite
37 of 42 people
found this instruction helpful.
-
Jack from Conroe, TX
- Really Easy
- Less than 15 mins
-
Screw drivers, Wrench set
(I knew the gas coils were bad, since the gas ignitor would glow brightly as the burner attempted to ignite. So I knew everything except the gas valve was operating normally.)
Unplug the electrical cord to the dryer. Remove the front access panel. Remove the retainer clip for the gas coils (2 screws). Remove the coils and unpl ... Read more ug the electrical connections. Connect the new coils to their respective electricl connections. Slide the nes coils back onto their respective posts on the gas valve. Replace the retainer clip, and 2 screws to hold it in place. (I then plugged the dryer back into the wall outlet to visually check the burner operation) Everything worked fine so I then replaced the front panel.
Unplug the electrical cord to the dryer. Remove the front access panel. Remove the retainer clip for the gas coils (2 screws). Remove the coils and unpl ... Read more ug the electrical connections. Connect the new coils to their respective electricl connections. Slide the nes coils back onto their respective posts on the gas valve. Replace the retainer clip, and 2 screws to hold it in place. (I then plugged the dryer back into the wall outlet to visually check the burner operation) Everything worked fine so I then replaced the front panel.
Read less
Was this helpful?
Thank you for voting!