11074413 Kenmore Washer - Instructions

All Instructions for the 11074413
91 - 105 of 201

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
cold water only dribbled into tub
0 of 1 people found this instruction helpful.
  • katherine from baton rogue, LA
  • A Bit Difficult
  • 1- 2 hours
  • Pliers, Screw drivers, Socket set
followed the video i found on Parts Select. Most difficult part was getting the frame back on correctly. Everything else was a breeze. Works great now.
Was this helpful?
Thank you for voting!
Water leakig into the tub after the cycle finished
0 of 1 people found this instruction helpful.
  • Kenneth from Palm City, FL
  • A Bit Difficult
  • 1- 2 hours
  • Pliers, Screw drivers
First I unplugged the washing machine and turned off the inlet water faucets. I prepared my tools, spead a drop cloth, and had ready a towel and small bucket to catch water from the hoses.
I pulled the washer away from the wall and removed the screw holding the ground wire. I disconnected the inlet hoses and the drain hose from the wall and put the loose ends in the washer tub. Then I completly turned the washer around for easy access. I removed the inlet hoses and the drain hose using the bucket to catch the little water that was still in the hoses. I removed 2 screws holding the top control panel to the back place and removed the 3 screws at the bottom of the back plate. I also removed the two screws holding the control panel to the top of the washer. The water inlet valve is located on the left side looking at the rear about half way up. I was able to move the left panel of the washer out of the way an inch or so, and pull the left side of the rear panel away a few inches so I could stick my hand in and unhook the cold and hot wire cables. I memorized which went into which slot. Then I unscrewed the water inlet valve and pulled it out the opening to the back and using a pair of pliers I loosed the water clamp and removed the rubber inlet hose. A small amount of water came out which I was able to catch in my small pail.
The water inlet valve comes with a separate mounting plate. I attached the mounting plate with one of the screws provided. The screws are identical except one has a flat slot and the other has a special star slot.
I reattached the rubber inlet hose using the pliers to hold the clamp then positioned the water inlet valve back in place on the back panel. I put a screw in to hold it and reattached the wires for the hot and cold control. Then I tightened the screws.

I repositioned the panels and put the lower screws holding the back panel to the washer back in loosely. I positioned the control panel back on the top of the washer and reattached the two screws on the back and then the two screws holding the front of the control panel to the top of the washer. Then I reattached the inlet hoses and draine hose.
I used this opportunity with the washer away from the wall to clean the floor and wall behind it. After cleaning under the washer, I moved the dryer over and cleaned under the dryer and made sure the dryer hose was still connected.
I put the dryer back, and repositioined the washer half way back into the opening. The I reattached the ground wire to the back of the dryer and attached the hoses to the wall. Then I pushed the washer back into place. Using a level I rechecked the level of the washer. I turned the water back on and ran a small load of wash to test. It worked fine.
Was this helpful?
Thank you for voting!
Getting only a trickle of hot water and a drip from the cold after cycle is done
0 of 1 people found this instruction helpful.
  • Steve from Manhattan, KS
  • Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
I watched the video provided and followed the same steps in taking the washer cabinet off. The valve was very easy to replace and I took the opportunity to really clean and inspect everything. A little tricky to get back together but not bad. My 25 year old kenmore is working like a charm.
Was this helpful?
Thank you for voting!
not cold water
0 of 1 people found this instruction helpful.
  • PEDRO from DAVIE, FL
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers
removed top panel and back panel
and then disconect the two wire fromm water inlet
fallow by removing screws.disconect water hose
then put back new part make sure i have all same conected as original put back panel top and back
conected hose for water back and electric .
then i turned 0n cold water perfect work hot water perfect warm perfect. problem fixed.
thanks. pedro
Was this helpful?
Thank you for voting!
Leak at hot-water inlet
0 of 1 people found this instruction helpful.
  • Christopher from Bowie, MD
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Wrench (Adjustable)
First - I saw the picture of the part on your site. It made all the difference.
Then, I turned off the water supply, unplugged the washer, removed the screws holding the backing plate on the washing machine to expose the valve.
After that, it was as easy as removing two mounting screws, disconnecting the solenoids (just two conn ections), pulling out the old valve and replacing it with the new.
Pretty simple and a lot less pricey when you can wait a few days for a part to come in the mail.
Was this helpful?
Thank you for voting!
Hot water would only trickle in.
0 of 1 people found this instruction helpful.
  • Helen from Louisville, KY
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers
I wish I could be more specific, but I had a bit of trouble getting the back off the washer. I removed the control panel on the top of the machine and that allowed me to get to the two clips that secured the back onto the unit. The I removed additional screws on the back until I was able to pull the back away from the frame on the side wh ere the valve was installed. after loosening the screws that held the valve to the back panel I was able to reach in and pull it out of the side. Once that was done, the rest was a breeze. I clipped the hose on the original valve and re-attached it to the new part. Then it was just a matter of reassembling and that went much, much faster than the disassembling. I reattached the water lines, plugged in the washer and it worked like a charm. I was very pleased with the whole thing. Also, I paid for standard freight, but received the part the following day after placing the order. Sweet.
Was this helpful?
Thank you for voting!
Washer not filling with hot or cold water
0 of 1 people found this instruction helpful.
  • Armando` from San Antonio, TX
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
I followed the instructional video that referenced the water inlet valve. The steps I followed were identical to the video I watched. That was extremely helpful. The hardest part was removing the terminal wires that connected to the inlet valve, the rest was very easy. With the new valve installed the washer works exactly as it did before . This site is very helpful, thank you!
Was this helpful?
Thank you for voting!
washing machine over flowing
0 of 1 people found this instruction helpful.
  • scott from mooresville, NC
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set, Wrench (Adjustable)
easy repair and so far so good stopped over filling so far hope this helps ... scott
Was this helpful?
Thank you for voting!
No cold water / inlet valve not working
0 of 1 people found this instruction helpful.
  • Barry from Logan, AL
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
I diagnosed by reversing the plugs on the hot/cold valves. I then removed the valve , cleaned it up and sprayed the electrical contacts with (Corrosion Block) and re-assembled. It still only had hot water. Ordered part, received part next day. When I went to install it I discovered that the (Corrosion Block) had penatrated and all was w orking! So now I have a spare valve.
Was this helpful?
Thank you for voting!
Hot water not going into machine
0 of 1 people found this instruction helpful.
  • Katherine from Greenville, NY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Opened back panel and replaced valve - very easy
Was this helpful?
Thank you for voting!
Water inlet valve would not shut off on cold side.
0 of 1 people found this instruction helpful.
  • George from Edgerton, WI
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
I removed the faulty valve after unplugging the AC cord. Two screws, the two water hoses were removed, and the electrical connections were unplugged. The old valve could then be rotated so that the clamp on the fill tube could be loosened and the tube pulled off the valve.
The new valve body seemed to be an exact replacement, but t he mounting bracked was slightly different and required drilling two new screw-mounting holes; an easy job.
Before securing the mounting plate to the machine, the fill tube and clamp were reattached, and the electrical connectors plugged in. After connecting the supply hoses and plugging in the AC cord, the machine filled with water properly and everything seemed to be back to normal.
I might have been able to use the original mounting plate, but it had been taken to a different location which was too far away to easily retrieve.
Was this helpful?
Thank you for voting!
Had no hot water flowing into the washer.
0 of 1 people found this instruction helpful.
  • Valan from Arlington, TX
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
I just followed the instructions from a previous customer. Worked perfectly.
Was this helpful?
Thank you for voting!
Dryer would not activate
2 of 7 people found this instruction helpful.
  • Andris from Sands Point, NY
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set
>removed 2 screws connecting the vent filter to the top lid of the unit (just in front of removable filter).
>Losing two screws at the back of the machine, just below control panel to allow free movement of the top lid on its hinges.
>Raise top lid & supported open.
>Now have free access to door switch (inside , front right fastened to front panel)
>removed the old switch
>fasten new switch (required new wire connector which was supplied with package) to existing wiring and replaced.
>Works perfectly!
Was this helpful?
Thank you for voting!
water inlet valve would not shut off because of warn out part
0 of 1 people found this instruction helpful.
  • walter from palmetto, FL
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
Take top of washing machine off. Turn spikets off and remove hot and cold inlet hoses. Remove one screw holding part in place. Reach from front and take valve out. Unplug wiring harnesses. Reinstall the same way I took it off.
Was this helpful?
Thank you for voting!
No hot water & very little cold water
0 of 1 people found this instruction helpful.
  • John from Royse City, TX
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
As I tore my ACL, my wife actually did the actual repair while I talked her through it. The video on your website was such a great help. Our repair went exactly as depicted.
Was this helpful?
Thank you for voting!
All Instructions for the 11074413
91 - 105 of 201