11074413 Kenmore Washer - Instructions

All Instructions for the 11074413
61 - 75 of 201

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Would not drain
1 person found this instruction helpful.
  • Robert from SANDWICH, IL
  • Really Easy
  • 15 - 30 mins
  • Wrench set
Replaced lid switch, but problem still continued.
Was this helpful?
Thank you for voting!
Inlet Water would not stop running.
1 person found this instruction helpful.
  • Paulette from FORT WORTH, TX
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Unplugged the power while the washer was running, and the water kept on running. The water inlet valve was stuck open. I removed the inlet valve and you cold blow air thru it, it should be closed with no power applied.Ordered replacement from this site it was a perfect fit. As far as the removal and installation procedure, just follow the video as presented on this site. Good Look.
Was this helpful?
Thank you for voting!
Water would not stop coming in when ran all the time
1 person found this instruction helpful.
  • Norwood from Peachbottom, PA
  • Easy
  • 1- 2 hours
  • Pliers, Screw drivers
unscrewed the back removd thr two screws for the element unhooked the hose to machiine unpluged the electric to element and than replaced new element and plugged electric to element and hooked back the hose and replaced screws too the back and replaced back an screws
titled wash machine up hooked hoses for the water and plugged el ectric and put drain hose back to drain done
Was this helpful?
Thank you for voting!
When washer was in cold water rinse cycle, loud squealing noise.
1 person found this instruction helpful.
  • James from LEXINGTON, KY
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Pliers
unplug unit first Took water & drain hose loose, used two wheel dolly, took washer out on patio. Removed water hose. Removed two screws # 49 an laid back control unit then Removed 2 #6 Clips Top of unit, then pried back unit cover out enough to remove Water valve after removing #4 screw that holds unit to back panel ,removed hose clam p #21 an electric connections, install new water valve and put back together..DO NOT TAKE BOTTOM SCREWS FROM BACK PANEL, if so the bottom will drop.. Intake cold water valve was half stopped up. Also new water lines.
Was this helpful?
Thank you for voting!
Dryer would not start, timer had no power to it.
1 person found this instruction helpful.
  • Billy from NEW BERN, NC
  • Easy
  • 30 - 60 mins
  • Screw drivers
Raise the top off of the dryer with a flat blade screwdriver in each front corner of the dryer. Disconnect power to the dryer. Remove old switch and install new switch. Test door and proper operation of dryer.
Was this helpful?
Thank you for voting!
The switch was not working so got a new switch
3 of 7 people found this instruction helpful.
  • satyavenkata from Bentonville, AR
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Unfortunately after i replaced the new switch the drier worked well. After it stopped for the 2nd time we wanted to put a load and start the swit lost contact. It was not working.It lost the contact with the circuit. No clicking sound the drier not functional. I guess need a new switch?
Was this helpful?
Thank you for voting!
Slow running cold water to washer.
1 person found this instruction helpful.
  • Phillip from EATONTON, GA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
1- Unplugged washer. 2- Turned off water supply to hoses hot and cold. (marked hoses H C) 3- Unscrewed hoses to washer. 4-Used phillips head screw driver to take out screws(2) at corners of washer. 5- Slid top of washer forward and lifted top off. 6- Took out retaining clips on each side of washer. 7- Slid frame of washer outward exposin g rear panel of washer for access to water inlet valve. 8- Used 1/4" drive to take out screw to inlet valve. 9- Removed inlet valve, unplugged the two connectors and removed clamp from hose to valve. 10- Replaced new inlet valve and reversed the process to assemble washer back together. Total time for repair, about 45 minutes. I now have full running cold water to washer. Thanks guys for the video you provided. Would purchase again if needed. Thanks again!!! Water Inlet Valve with Mounting Bracket Part Number: PS334646
Was this helpful?
Thank you for voting!
Water would not stop running
2 of 4 people found this instruction helpful.
  • Judy from BERNVILLE, PA
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Wrench (Adjustable)
Followed by installation on line
Was this helpful?
Thank you for voting!
No problems
1 person found this instruction helpful.
  • Wayne from ZEPHYRHILLS, FL
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
I got a few hints from YouTube (how to remove the washing machine casing) and rest was very simple
Was this helpful?
Thank you for voting!
water inlet valve bad
1 person found this instruction helpful.
  • linville from lily, KY
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
received valve as ordered a simple installation. everything went well.home owner can do this repair
Was this helpful?
Thank you for voting!
water valve neede replaced
2 of 4 people found this instruction helpful.
  • Timothy from summerfield, FL
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set
The valve was easy to change, but we as homeowners should change the hot and cold hoses just like they say you should every 5 years. The hoses grew to the water valve and it was almost a disaster. After cutting the end with a dremmel and clamping visegrips on it I finally got it loose. After that it went smooth. Thanks for getting me the part so fast.
Was this helpful?
Thank you for voting!
Cold water input into the washing machine was very slow.
1 of 2 people found this instruction helpful.
  • James R from Birmingham, AL
  • Difficult
  • More than 2 hours
  • Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
The hot water hose was frozen to the hot water bibb and it took me a while to cut it loose with my Dremel tool. Removed the cabinet and replaced the water inlet valve easily, then hooked up new hot and cold water hoses. Reinstalling the cabinet was a little tricky getting it lined up correctly. Checked for leaks then tested the washing machine and it ran great with the water filling the machine much faster with the new Water Inlet Valve. I will definitely replace the washing machine hot and cold water hoses every 5 years from now on.
Was this helpful?
Thank you for voting!
Washer exhibited LOW cold water flow and dripping when off.
1 of 2 people found this instruction helpful.
  • Cory from Alexandria, VA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
The repair went great. The video shown on the partselect site saved me a huge amount of time disassembling the cabinet to access the malfunctioning part. The most difficult part of the repair was replacing the cabinet on the unit after the part swap and getting it straight. Luckily 2 attempts was enough. I recommend trying this repair yourself and saving a bunch of $$.
Was this helpful?
Thank you for voting!
Lid switch failed, dryer stopped working
1 of 2 people found this instruction helpful.
  • Rick from BETHESDA, MD
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Order replacement lid switch, installed it, good to go. The installation video and instructions with the replacement part were very helpful.
Was this helpful?
Thank you for voting!
washer continued to spin when you raised the lid not shutting off
1 of 2 people found this instruction helpful.
  • Daniel from TRENTON, NJ
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Your web site is amazing Ive enjoyed watching your videos,this is a really great way to see what it takes to repair your washer very informative. Steve was a good teacher for me I just followed along as he explained each step and my washer came apart just like he said. I removed the two front console screws and pulled slightly forward and lifted console up and tilted it back where it was out of the way. next I was able to lift cabinet up from the back and remove it from the frame and lay cabinet on the floor on top of a rug I had to protect the finish on cabinet . Now I had access to the lid switch and simply removed the two screws in the cabinet and the old switch. I connected the two wire connections to the new switch (no)normally open connection, used same actuator the instructions say to do this because the one that comes with the new switch won't fit so use the old one. on my washer there's a cover that fits under this switch and It took me a little longer to get the screws to line up so they fit through the switch and into the cover but It worked fine. Now all I had to do was reinstall the cabinet just like Steve did on the video my only problem with this was seeing where the tabs in the frame were located so that the slots in the cabinet would fit over top of frame tabs I used a flash light in one hand and lowered the cabinet down I held the light on the frame tabs and the slots in cabinet fit right in then lowered cabinet to the rear frame tabs where i just had to push slightly on the sides of cabinet and it fit right in.Next i pushed the back panel in place and on the top of washer just like in video reinstalled both spring clip clamps and the console and reinstalled the two screws. I plugged in the washer put drain hose back in drain pushed washer back in place turned it on working great now ! Thank You so much for your help Dan.
Was this helpful?
Thank you for voting!
All Instructions for the 11074413
61 - 75 of 201