11074413 Kenmore Washer - Instructions

All Instructions for the 11074413
46 - 60 of 201

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
The cold water wash would not work.
2 of 3 people found this instruction helpful.
  • Michael from Roanoke, VA
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
Initially, we thought the problem was in the water inlet valve and we changed it out. It went OK although the Kenmore almost fell apart after the removal of a few screws and the control unit.
Only thing was that it was unncessary. The real problem was not in the cold water turn on valve, but in the hose. The hose was special i n that it was designed to shut off under emergency conditions. It appeared to be able to passs water when tested at my sink, but when connected to the washing machine and under presssure, it would not pass water. I had installed the part by this time so I left it there. I found the Kenmore washing machine rather flimsy in it's construction and tended to totally come apart once a few screws were removed.
Was this helpful?
Thank you for voting!
water wouldn't run out of washer
4 of 9 people found this instruction helpful.
  • James from Richmond, VA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Two screws holding top, unhook wire conector. remove cabinet,replace switch. Reassemble.
Was this helpful?
Thank you for voting!
Dryer would not start.
2 of 3 people found this instruction helpful.
  • Victoria from Roslyn Heights, NY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
My dryer is 35 years old and thought this was it, but I googled the question and found out it was the door switch. Orderd the part and received it very fast and didn't want to wait for my husband to come home so I went on you tube and found a video how to open dryer and change switch. I did it in about 30 min. and yes it is now perfect ag ain. No problems. I just unscrewed the old switch and put the new one in. Maybe I'll get another 35 years out of this machine. :o) Thanks for making it so easy.
Was this helpful?
Thank you for voting!
It was the heat safety switch in the old drive motor
2 of 3 people found this instruction helpful.
  • Andrew from HATTIESBURG, MS
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
It was fairly easy a few tight spaces to reach in but all in all it was pretty straight forward
Was this helpful?
Thank you for voting!
Threads stripped on water inlet valve.
3 of 6 people found this instruction helpful.
  • Edward from Pittsburgh, PA
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
The replacement of the water inlet valve was not too difficult after reading the steps posted by others. The main step is to unscrew the top control panel first, remove the top 2 screws of the back panel, and you have easy access to the water inlet valve. No need to remove the entire back panel. Follow the instructions which accompany th e replacement water inlet valve and you should have no problems. The washing machine now fills faster with the replaced water inlet valve. The replacement inlet valve arrived within 2 days of ordering! Thanks for the superfast shipment!
Was this helpful?
Thank you for voting!
Leaking water inlet valve
3 of 6 people found this instruction helpful.
  • Ricky from Waterloo, IL
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set
1. Unplug washer, close hot and cold water supplies and remove water hoses from washer inlet valve.
2. Remove two screws at the bottom of the front of the control panel.
3 Remove two screws at the top of the back side of the control panel.
4. Remove control panel.
5. Remove two retainer clips that hold the back panel t o the top of the cabinet by prying them out from the front with a large screwdriver. (Probably the most difficult part of the job.)
6. Use a socket or nut driver to remove the two screws that hold the valve to the back panel.
7. Lift the cabinet from the bottom rear and tilt the cabinet forward until you can access the valve.
8. Remove the wire harnesses from the hot and cold valves taking note of the wire orientation. (The red one will go back on the hot valve.)
9. Use pliers to open the hose retainer clip and slid the clip out of the way and remove the hose from the valve.
10. Reverse the process and you are done!
Was this helpful?
Thank you for voting!
water dripping into tub when off
2 of 3 people found this instruction helpful.
  • Dave from Coral Gables, FL
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Removed two screws holding top control section on, and folded back the control panel. Removed two clips holding cabinet on, tipped cabinet toward me and off. Removed and replaced water valve, being careful to mark hot/cold hoses, and secure the internal hose to the valve with the spring clamp. Most difficult part was lining back up the ca binet when putting it back on the base, but a few minutes to line up tabs and get the front of the cabinet UNDER the front groove in the base got it secure. Works fine now.
Was this helpful?
Thank you for voting!
cold water wasn't shutting off between fills on washer
1 person found this instruction helpful.
  • Daniel from Delavan, WI
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Wrench (Adjustable)
Turn off water, unplug machine
Disconnect water lines to the valve
Unscrewed the clear plastic tabs on the top of the machine, then pryed the back away from the top white part.
Two gold clips can be popped out with a long flat head screw driver.
Pulled the back away from the machine enough to disconnect the wires from the valve. Unscrew the screw(s) from the valves.
Old valves out, new valves in. Plug in the wires, screw in the screws.
Then, to get the gold tabs back in place.....i called NASA.
just kidding. They're tough!
I slipped one into the back and held it in place with my thumb. Then I lined the piece up with the slot inside the machine. Then, i pryed the top white part away as I pushed them together. Stuck a long handle screwdriver down in and pushed REALLY hard on the gold tab to get it to snap into place. Everything is really tight, so you might have to try it a few times.....i left some blood behind.
repeat for the other side, snap in the clear tabs, hook up the water lines, plugged it in......
Then I sat back and listened to my wife praise me for fixing her machine!
Was this helpful?
Thank you for voting!
Cold Water valve would not shut off
1 person found this instruction helpful.
  • John from Fair oaks, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Removed two clips on back panel holding control panel.Removed end plates on control panel. removed two front screws holding control panel. removed wiring harnesses noting location. Set control panel aside. Removed two large clips holding rear panel to washer cabinet. Pulled washer cabinet from the front away from the rear panel and tube. Removed two screws holding water inlet valve. Removed water inlet hose from inlet valve using channel lock pliers. Installed new water inlet valve using supplied mounting bracket. Reassembled washer in reverse order.
Was this helpful?
Thank you for voting!
Washer wouldn't fill up with hot water
1 person found this instruction helpful.
  • Paul from Winston-Salem, NC
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable)
I just followed the instructions found on this website. It covered everything you need to know. I have just one thing to add though. Look over everything first and formulate a game plan. Keep all screws etc. and put them in a plastic bag so you don't lose them. You might try using a heavy hammer to force the clips holding the back panel t o the top of the machine back in place. One more thing; use a piece of wood to set the back panel on while you replace the intake valve.
Was this helpful?
Thank you for voting!
Dripping When Washer is Off
1 person found this instruction helpful.
  • Herbert from Daly City, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers
This should have been done under 30 minutes but when you don't have a repair manual, you have to do some guessing. I have to remove the back panel. On only thing that was hard was unspringing the two flat springs. After I got the panel off, the rest was easy and the dripping stopped. Oh, there is a screen where the hose connects to t he inlet valve. If you can clean the screen often, you can continue to get a good water flow.
Was this helpful?
Thank you for voting!
washer would partially fill itself when not in use
1 person found this instruction helpful.
  • Adrian L from Houston, TX
  • A Bit Difficult
  • 30 - 60 mins
  • Wrench (Adjustable)
I had to call in to find the correct part because the online recommended part looked very different, and the one found using the model number had no photo, so I was VERY leary of ordering. The service rep said that Kenmore products did not always show up correctly and he gave me the part number needed and there was a photo. The part was not exactly the same, but looked very similar and it was more than 50% less than the original recommended part and part with no photo. I thought that the problem finding Kenmore parts was odd since Kenmore is like number one, right? Part took 3 days to arrive, which I thought was great. Turned off power and water. Removed water hoses. Removed three screws from the back of the top (front loader). Removed the top. Removed a screw holding on the water inlet valve from the outside of the unit through the back cover which required a star driver. Unattached the 4 electrical leads. Unattached the outlet water hose (held on with a squeeze type metal clamp -not sure of the exact name for these). The problem that I had was that the water outlet hose bib attachment was slightly larger than the old one, so the hose would go back on, but the clamp was too small so I cusses a lot before figuring out the problem. I had to go and purchase a new larger clamp. After that, I simply attached the electrical connections and put the outlet back on. One other small problem was that the place where the screw through the back cover was originally attached no longer lined up with the new valve. The plastic piece was shorter than the old one so the screw hole did not line up with the hole in the back panel. The screw isn't really necessary. Overall, replacing the part was easy and I was pleased with the process.
Was this helpful?
Thank you for voting!
Water would not stop filling out the tube.
1 person found this instruction helpful.
  • GEORGE from WEST HILLS, CA
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
1- Remove power connection, remove water connections. 2- Remove the top controller box and free it from its hinges. 3- Loosen the back cover to get access to water valve assembly. 4- Remove hose clamp connected to inlet water valve. 5- Remove the old water valve which is secured with 1/4" screw. 5- For installation perform step 5 to 1 and then test your Installation.
Was this helpful?
Thank you for voting!
Won't pump out the water
1 person found this instruction helpful.
  • Victor from NORFOLK, VA
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Order the part and put the new part on and put the washing machine cabinet back on and check the washer for the water filled up and then it's starting to go on the spin cycles.
Was this helpful?
Thank you for voting!
The agitator had stopped working
1 person found this instruction helpful.
  • Jack from Matthews, NC
  • Easy
  • 15 - 30 mins
  • Socket set
We got the parts, watched your video a couple of times and then began the repair. It went well with one exception. None of my socket extensions were long enough to work well. The required length might be added to the video and the printed installation instructions. Also it would have nice to have been able to order a small tube of the rec ommended lubricant. Overall I was very pleased. Jack
Was this helpful?
Thank you for voting!
All Instructions for the 11074413
46 - 60 of 201