1106607921 Kenmore Dryer - Instructions

All Instructions for the 1106607921
106 - 120 of 326

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer was making all kinds of noises
1 person found this instruction helpful.
  • Noel from N BRANFORD, CT
  • Easy
  • 30 - 60 mins
  • Nutdriver, Socket set
After checking out the website and the videos posted to YouTube, I decided that I should take a chance and try and repair the problem myself. I am not in any way mechanical, and for me personally, this was a huge job. The instructions and the video were so clear that it made the job easy. Taking out the dryer drum was a concern, and altho ugh not heavy, I used a friend to hold it in place when I was putting it back together. My only small issue was when I was removing the rollers. I had some difficulty taking off the plastic locking washers but other than that, it was a breeze. The videos posted are great and very easy to follow. While doing the above job, I also replaced the dryer belt and heating element, both of which I followed instructions as per video. The dryer is running very smooth, and is the quietest it has been for many years. Very happy with all aspects of service advice and videos.
Was this helpful?
Thank you for voting!
Dryer was making a lot of noise while running.
3 of 7 people found this instruction helpful.
  • Ramon from Los Angeles, CA
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers
After identfying that the problem was due to a damaged drum support roller, I decided to replace the bad roller instead of replacing the dyer itself.

The first thing was to remove the front cover
and the front panels to expose the drum. (Only a few screws hold them in place.) Next, the drum was removed by first releasing t he belt from the motor pulley and tensioner, and then pulling the drum straight out.

At this point the two rollers would be exposed. The triangular plastic retaining locks were removed by slightly prying them off. The old rollers were then removed and replaced.

Before putting everything back, this was a good time to vacuum all the accumulated lint inside, especially the lint that had accumulated around the motor assembly and the fire box.

(A pleasant surprise: I found a lot of coins inside the unit, enough to recoup half of what I spent for the new rollers.)
Was this helpful?
Thank you for voting!
broken door catch
1 person found this instruction helpful.
  • Susan from HUDSON, MA
  • Very Easy
  • Less than 15 mins
  • Pliers, Screw drivers
I followed your short video and found it very easy to do
Was this helpful?
Thank you for voting!
Dryer drum wasn't turning
1 person found this instruction helpful.
  • Carrie from PLAINFIELD, IL
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Wrench (Adjustable)
Found the belt was broken and the pulley wheel had melted, replaced the belt and the pulley, could not have been simpler. Watched the video on how to repair and in less than 15 mins was fixed. Saved a lot of money by doing it myself.
Was this helpful?
Thank you for voting!
Machine would not start and light stayed on with door closed.
1 person found this instruction helpful.
  • Mark from TERREBONNE, OR
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Turned off circuit breaker to machine. Removed lint trap to allow removal of two Philips screws from vent passage that hold lid on. Opened door and removed two Philips screws that hold switch to front of machine. Using flat blade #2 screw driver pushed on plastic locking tabs under front of machine top about 2" in from either side to allo w top to be lifted up from machine. While holding up at 45 degree angle reached in and grabbed switch to pull it out for easy access. Set top down gently once switch was out. While holding switch removed broken switch actuator and installed new actuator on to switch. Lifted top back to 45 degree angle and with left hand held switch assembly in place and started two screws previously removed back into actuator holes. Tightened screws snugly. Lowered top back into plastic locking tabs and gently pushed down to secure top. Installed two screws back to air passage tube for lint trap through two holes in top that were removed at beginning of repair. Install lint trap, turn on circuit breaker and verified operation. Put wet clothes in tub, turned machine on, put away two screw drivers and kissed wife apologizing for taking so long to getting around to repairing machine.
Was this helpful?
Thank you for voting!
broken door catch
1 person found this instruction helpful.
  • Frank from ENDICOTT, NY
  • Very Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Took 3 screws out used the putty knife to pry the door a part then used the pliers to remove the old door catch and then sapped the new one and put the door back together and I was was done in less than 10 min.
Was this helpful?
Thank you for voting!
latch was broke
1 person found this instruction helpful.
  • Rick from SAN DIEGO, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
just followed the video directions, worked perfectly thanks
Was this helpful?
Thank you for voting!
Dryer door would not stay closed
1 person found this instruction helpful.
  • Gregg from St. Augustine, FL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
After removing front door panel (2 screws) I removed the old latch catch and replace with the new part. 4 minutes later, the door was back together, the dryer was running and the door was staying closed.
Was this helpful?
Thank you for voting!
dryer would not run because catch did not hold tight enough to press door switch.
1 person found this instruction helpful.
  • j from TAZEWELL, TN
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
removed screws that held the door face to gain access to catch replaced catch reassembled door tried dryer works great!
Was this helpful?
Thank you for voting!
Door catch was cracked
1 person found this instruction helpful.
  • Tammy from glenford, OH
  • Very Easy
  • Less than 15 mins
Incredibly simple! You just pop the other plastic catch out with a butter knife and pop the other on in. This is the second time I have done this over the last 4 years or so.
Was this helpful?
Thank you for voting!
Door would not stay closed - so dryer kept shutting off
1 person found this instruction helpful.
  • Barbara from NORTH EASTON, MA
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Followed Youtube video - quick & easy
Was this helpful?
Thank you for voting!
Broken dryer door catch
1 person found this instruction helpful.
  • Kenneth from UPPR MARLBORO, MD
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Followed the video instructions which were comprehensive, easily understood, and prefaced with a listing of necessary tools. Completely satisfied with parts and supplementary information.
Was this helpful?
Thank you for voting!
Old filter handle broke
1 person found this instruction helpful.
  • ronald from PICKENS, WV
  • Really Easy
  • Less than 15 mins
replaced filter
Was this helpful?
Thank you for voting!
Handle on lint filter cracked and came apart
1 person found this instruction helpful.
  • ROSEMARIE*SALVO from BRONX, NY
  • Very Easy
  • Less than 15 mins
Opebed lint filter door, removed old lint filter and replaced it with new one.
Was this helpful?
Thank you for voting!
dryer door wouldn't catch, catch was broken
1 person found this instruction helpful.
  • Theodore from Tyler, TX
  • Really Easy
  • Less than 15 mins
took the cstch reciever out, with my fingers, pushed the new one in, snap lock fit.......couldn't be better, like repairing a model T ford.......
Was this helpful?
Thank you for voting!
All Instructions for the 1106607921
106 - 120 of 326