- Home
- 1106607921
- Instructions
1106607921 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer was making a loud sound
2 of 2 people
found this instruction helpful.
-
Frans from N ARLINGTON, NJ
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set, Wrench (Adjustable), Wrench set
I follow the instructions from the video you guys show the only issue is putting back the tensioner in place but my brother leaves next door and help me.
Was this helpful?
Thank you for voting!
Noisy while in use.
2 of 2 people
found this instruction helpful.
-
Charles from ERIE, PA
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
Turn off Gas, unplug electric cord, remove rear cover, remove two screws holding the lint trap to the top, raise top flip[ping to the back supporting it not to damage wiring, remove bottom front cover, remove door springs, remove front cover, disengage belt tensioner, remove drum. unclip right side roller and remove, unbolt left wheel
... Read more
mount from the rear and the bracket in the front, remove clips or cut off (new ones come with new clips). clean the wheel shafts, light sanding if needed, apply light coat of lithium grease. replace wheels and reassemble dryer in the reverse order from disassemble. roll drum by hand after front back on to ensure it rolls without catching. Finish and test.
Read less
Was this helpful?
Thank you for voting!
Dryer stopped working.
3 of 5 people
found this instruction helpful.
-
Andrew from Edina, MN
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
I followed the on-line video. I am extremely happy I made the effort and successfully fixed my dryer on my own. It sure beats a new dryer expense or high repair cost.
Other Parts Used:
Was this helpful?
Thank you for voting!
The original motor stopped working
2 of 2 people
found this instruction helpful.
-
Robert from PFLUGERVILLE, TX
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Had to replace the rear felt seal and the motor. It was no problem to find videos on how to do both of these repairs. Took apart the appliance. When the parts came first replaced the drum rear felt seal and waited for the motor to be delivered. Then replaced the motor as per online instructions. Also went to Home Depot to buy a new flexib
... Read more
le dryer tube since the old one had a few holes. It works perfectly again.
Read less
Was this helpful?
Thank you for voting!
Bad Motor, Would not start.
3 of 5 people
found this instruction helpful.
-
Steve from S LAKE TAHOE, CA
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
First unplug appliance, Remove dryer top and front. remove drum and belt. Two clamps hold motor in place. remove them and lint chute housing in rear, exposing the fan. Use vice grips to hold motor shaft behind belt pulley flat spot. Remove fan, it's reverse threads. A large adjustable wrench on plastic fan nut and spray lubricant if very
... Read more
tight. Place new motor next to old and switch wires over, crimp on new 1/8'' connectors. Remember the green ground wire may need an allen wrench. Put back drum,belt, lube the rollers and replace back cover, front, top.
Read less
Was this helpful?
Thank you for voting!
Loud banging coming from drum area.
2 of 2 people
found this instruction helpful.
-
Larry from S ROCKWOOD, MI
- Really Easy
- 1- 2 hours
-
Nutdriver, Screw drivers
I watched a U Tube video about banging sound from dryer. Once I recognized the problem, lifted the top, removed 2 screws holding the front, removed the drum, and bingo. Saw the worn out drum roller. Ordered the replacement parts from "PartSelect" on line (Great Company). Was in no hurry, so I chose regular mail delivery. 4 days later, got
... Read more
the correct replacement parts, put the dryer back together, and now, the dryer is quieter then when I bought it new, a thousand years ago. I will never again be afraid to tackle an appliance issue. THANK YOU !!!
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer tumbler made a loud noise
2 of 3 people
found this instruction helpful.
-
jeff from albuquerque, NM
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers
Disassembled dryer, removed tumbler, replaced drum support rollers
Was this helpful?
Thank you for voting!
Blower (fan) assembly and old model motor with different electrical connections
2 of 3 people
found this instruction helpful.
-
Dana from RESTON, VA
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
1 Vice grips are required to remove the fan/blower. Clamp on inside of dryer so you can remove the blower/fan assembly
Recommend 10" or larger 14" will definitely do the job
2. Blower/fan is reverse threaded when facing the back of the dryer. That is how I broke mine. Turn clockwise to loosen - feels very unnatu ... Read more ral
3. If you have to replace the 5 & 6 electrical connectors, you have to have a barrel crimper for insulated terminals - IWISS SN-02C RATCHET TERMINAL CRIMPING PLIER TOOL, 24-14AWG is a good example
Recommend 10" or larger 14" will definitely do the job
2. Blower/fan is reverse threaded when facing the back of the dryer. That is how I broke mine. Turn clockwise to loosen - feels very unnatu ... Read more ral
3. If you have to replace the 5 & 6 electrical connectors, you have to have a barrel crimper for insulated terminals - IWISS SN-02C RATCHET TERMINAL CRIMPING PLIER TOOL, 24-14AWG is a good example
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
drum support roller was squeaking VERY loud
2 of 3 people
found this instruction helpful.
-
joe from southgate, MI
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
lifted top section of dryer
removed front dryer panel
removed drum belt and tensioner
removed both drum rollers
cleaned both roller axles
installed new rollers
reassembled remainder of dryer
if you are at all mechanically inclined, it is a simple job
removed front dryer panel
removed drum belt and tensioner
removed both drum rollers
cleaned both roller axles
installed new rollers
reassembled remainder of dryer
if you are at all mechanically inclined, it is a simple job
Was this helpful?
Thank you for voting!
Dryer wouldn't restart when start button pressed
2 of 3 people
found this instruction helpful.
-
Charles from Cape Girardeau, MO
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
Before beginning, unplugged dryer. 1) Used putty knife at each front corner of top to pop lid loose from clips. 2) Removed hex screws at back of control panel to allow lid to tip open. 3) With lid opened, removed hex screw from inside-top of each side to allow front to pull open from side panels and access door switch easily. 4) Removed c
... Read more
lip that holds retaining wires from top. 5) Pulled wire from each side of door switch. 6) Removed switch assembly using Phillips screwdriver to remove two screws mounting switch at top of door opening. 7) Removed broken actuator spring and replaced. 8) Reversed process to reassemble.
Read less
Was this helpful?
Thank you for voting!
Worn bushing on bottom drum roller
3 of 6 people
found this instruction helpful.
-
Frank from Avon, CT
- Easy
- 30 - 60 mins
-
Nutdriver, Socket set
unplugged power, slide unit away from wall, removed bottom front cover, rear sheetmetal cover, tilted front of unit to remove roller outboard support (sheetmetal screw from bottom of dryer). Removed shaft bolt from rear of dryer which released roller assembly. Remove speed nut from old roller assembly to remove outboard support arm, mount
... Read more
ed new roller to new shaft placed triangle clips (one each side of roller), mounted outboard support to front of new shaft and completed re-assembly (reverse order of disaasembly).
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Blower flywheel needed replacement
2 of 3 people
found this instruction helpful.
-
Gary from SAINT LOUIS, MO
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Socket set, Wrench (Adjustable)
After watching the U Tube video to replace flywheel, I had a appliance repairman come to my home to install flywheel. There was no way I would have been able to put the dryer back together without some help.
I want to say "Thank You" to the sales representative who assisted me when purchasing my items, she was very patient while run ... Read more ning around the house looking for the model number of the dryer.
I want to say "Thank You" to the sales representative who assisted me when purchasing my items, she was very patient while run ... Read more ning around the house looking for the model number of the dryer.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
metal spring in door broke the peice that allows the drum to spin
2 of 3 people
found this instruction helpful.
-
katherine from Salem, OR
- Easy
- 15 - 30 mins
-
Screw drivers
This was rather easy to fix. I had never opened the dryer before but had a serviceman come out so I knew that you can pop the top of the dryer off by putting a flat edge screwdriver in between the top and bottom and popping up. You must remove the screws from the lint dryer before so the top comes off. The piece to replace had two screw
... Read more
s and that was it. To get a repairmen from Sxxrs where we purchased it 15 years ago they charge a flat fee of $75 just to come out. That does not include the repair just a fee to come and tell you how much more it would cost to fix it. I ordered the part for less than $5 and $12 more for 2-3 day delivery! What a bargin! I was back drying clothes 15 minutes after the part arrived! Very happy that the part is still being made!
Read less
Was this helpful?
Thank you for voting!
Door switch actuator spring broke
2 of 3 people
found this instruction helpful.
-
Laszlo from Vienna, VA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Disconnect dryer.
Unscrew the two screws that hold the door actuator assemby.
replace broken spring.
Screw the the two screws back.
Unscrew the two screws that hold the door actuator assemby.
replace broken spring.
Screw the the two screws back.
Was this helpful?
Thank you for voting!
Loud noise while in use
2 of 3 people
found this instruction helpful.
-
Josh from Madill, OK
- Really Easy
- 15 - 30 mins
-
Screw drivers
Replaced roller. Very simple. Dryer is the easiest appliance to repair. Only a few parts keep a dryer working
Was this helpful?
Thank you for voting!