1106607921 Kenmore Dryer - Instructions

All Instructions for the 1106607921
91 - 105 of 326

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Fan blade had to be removed , was broken off from motor.
2 of 3 people found this instruction helpful.
  • James from Colorado Springs, CO
  • Very Difficult
  • More than 2 hours
  • Pliers, Screw drivers
Had to completely dismantle the dryer including the motor and grind off the.bolt holding the fan blade on. I did not realize it was threaded on with a left hand thread.Then reassembled.
Was this helpful?
Thank you for voting!
Dryer door wouldn't catch and stay shut
1 person found this instruction helpful.
  • Melody from TEXARKANA, TX
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
I take the screws out of the door, I removed the catch from behind inside the dryer door, I slid the new catch in the door and snapped it in place. After getting a new catch in the door I put the door back together and put the screws in. Easy repair
Was this helpful?
Thank you for voting!
broken belt
1 person found this instruction helpful.
  • William from Newport, VT
  • Easy
  • 15 - 30 mins
  • Nutdriver, Socket set
removed two screws from lint screen raised top removed two nut screw from front disconnected lid wire lifted front up and off removed drum cleaned all dust out replaced pulley unit with new one (with a wheel) replaced tub held it up with a bungey cord put on new belt and reassembled unit tested out back in busine ss
Was this helpful?
Thank you for voting!
Noise in dryer when dryer was turned on
2 of 4 people found this instruction helpful.
  • Michael from Marion, KY
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set, Wrench (Adjustable)
Removed the drum then removed the old parts and installed the new ones. Dryer now runs very quite and heats good. You have very fast service my mother ordered the parts on the net one day and I received the parts next day and did the repair that night and dried clothes. Thanks,

Your great service is very hard to find.
Was this helpful?
Thank you for voting!
My daughter threw a heavy wet comforter into the dryer and the tri-ring sheared off.
1 person found this instruction helpful.
  • Joe from St. Louis, MO
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.
Was this helpful?
Thank you for voting!
door would stay closed
1 person found this instruction helpful.
  • william from KILLEEN, TX
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
just replaced parys
Was this helpful?
Thank you for voting!
Dryer was making a loud rattling noise and shaking
1 person found this instruction helpful.
  • Lindsey from Lancaster, PA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Wrench (Adjustable)
I watched the part select you tube video that links specific loud dryer noises to specific broken or loose parts. It allowed me to identify the part I needed, which I ordered through their website. Two days later, I had the part and installed it, with help from another online video that showed me how to take the dryer apart to install the drum support roller. Thank you, the information provided made the repair quite easy. It works perfectly now!
Was this helpful?
Thank you for voting!
Dryer making excessive noise; then continued to blow circuit
1 person found this instruction helpful.
  • Ava from BALTIMORE, MD
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set
Attributed excessive noise to age of dryer, upon closer inspection, a dish towel had become caught at rear of drum because the drum support rollers were damaged causing the drum to create a space in the rear of the drum. This was large enough for the dish towel to be caught. Originally I thought that the thermal fuse had blown the circuit -which should occur in an overheating situation-however the loose drum had worn through the electrical wire leading to the door switch because it was not properly seated on the rear drum rollers. the wire was repaired with a wire nut, rear drum rollers were installed and it is working again. thank you for the extremely fast shipping
Was this helpful?
Thank you for voting!
rollers had been new too long!
1 person found this instruction helpful.
  • Scott from EVEREST, KS
  • Very Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
Took of the btm pan and the top to be able to remove the front. Raised the drum enough to replace the right hand wheel. ( the old ones had already been removed) Replace the left hand wheel and bracket. Re assemble the machine. Worst part was trying to do all this with the can of beer in one hand!!
Was this helpful?
Thank you for voting!
Light stayed on, inside dryer. Dryer no workie
1 person found this instruction helpful.
  • Steven from New Richmond, WI
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
I diagnosed the problem, as a broken arm on the actuator for the door shut switch. I jumped the switch, and dryer worked. I went to this site, found the part I needed, ordered it/received it quickly, and proceeded to do the repair. The video that THIS particular part goes for, isn't' like MY dryer. My dryer hinges in the rear. You just remove the 2 screws on either side of the control panel, (right and left), pull forward on the panel, to ease its attachment, let it lie. Then with a small plastic pry tool, pop the 2 attaching points in the front of the dryer. Front end lifts up, like a hood on a car. My roommate held hood up, while I R&R'd the switch actuator. Went back together, in reverse of my taking apart. Worked great. Thanks a bunch.
Was this helpful?
Thank you for voting!
Drum rear seal bad
1 person found this instruction helpful.
  • Ron from COAL CITY, IL
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Took off old one clean surface up then put glue all around drum seal area wait one min. Or tacky then put seal on reassemble the drum. Works good
Was this helpful?
Thank you for voting!
Dryer was not drying clothes with-in 40 minutes. Found lint guard was not sealed properly at base, exhaust hose full of lint.
1 person found this instruction helpful.
  • Charles from Rupert, ID
  • Really Easy
  • 30 - 60 mins
This model you cannot lift the top lid without breaking it. Removed the exhaust hose and back of dryer. vacuum out the dryer and hose to remove the excess lint. Remove screws from the lint guard mounting. Loosen and remove 4 screws that hold the lint guard in place. The seal at the base of this assembly was missing the seal around the dis charges fan. Remove seal with putty knife. Use a small brass wire brush to remove as much as you can. Vacuum area. Reinstall the lint guard assembly, start at the top, gently life and push assembly up and in. You should be able to determine how far. Start the bottom 4 screws, tight them. Check fit. Then put the screw back in on the lint guard on the top of dryer. Once you have completed this connect exhaust hose. Start dryer, check the dryer exhaust vent that is outside. If the flow is good, WELL DONE!

Recommendation: Check this assembly by removing the back of the dryer approximately every 6 mos. for lint build up. Not doing this may increase the risk of fire.
Was this helpful?
Thank you for voting!
Dryer would not heat and the timer would not turn as it should
1 person found this instruction helpful.
  • Jeff from OAKLAND, TN
  • Really Easy
  • 30 - 60 mins
  • Socket set
I replaced a bad thermostat
Was this helpful?
Thank you for voting!
dryer stopped and smelled of smoke.
2 of 4 people found this instruction helpful.
  • Jon from LaGrange, IL
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
I reviewed several videos on parts sites and YouTube. There is more than enough advice online showing step-by-step instructions. The only difficulty came with the rear nut holding the motor shaft to the blower fan. I used a crescent wrench with a long pipe over it for added torque. The two spring clips holding the motor in place can be removed and installed with the help of a nutdriver pushing the clip down, . The dryer was new enough so the motor needed no switch changes. The new motor is running fine.
Was this helpful?
Thank you for voting!
Buzzing sound while start button pushed. then shut off after 30 seconds.
2 of 4 people found this instruction helpful.
  • Brad from Lake City, FL
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Wrench (Adjustable)
Removed 2 screws holding the lint trap on top, popped up the top and lifted back, removed 2 screws on the inside top of front panel, lifted front off and set aside then reached under the drum and pulled tension pully to loosen the belt, and removed the drum. popped the motor clams off and then used 2 adjustable wrenches to grasp the nuts at the front and back to remove blower fan. When you look for the area in back to loosen the blower fan you may notice the nut that you are looking for is actually part of the fan and is plastic looking rather than metal. I did have to take off the back cover to the blower fan to tighten it back up.I had seen instructions that the blower fan would have a 3/8 hole in the back of it to loosen it,but mine did not. I assembled it and it works great with my new motor and rollers. I received my part in 2 days, very happy
Was this helpful?
Thank you for voting!
All Instructions for the 1106607921
91 - 105 of 326