110616 Kenmore Dryer - Instructions

All Instructions for the 110616
91 - 105 of 293

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Hard to reach the screws inside the dryer They were on the door side of the dryer and hard to reach, especially if you are a abig guy.
3 of 3 people found this instruction helpful.
  • Lucy from CHADDS FORD, PA
  • A Bit Difficult
  • More than 2 hours
  • Screw drivers
Removed the dryer door, unscrewed lint vent.
Was this helpful?
Thank you for voting!
Loud squealing when the dryer was running...especially on start up.
4 of 6 people found this instruction helpful.
  • Anthony from GROVELAND, IL
  • Really Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers
Simply followed the video that accompanied the part confirmation. Removed the top and front of the dryer. Removed the drum and belt. Unbolted (1 bolt) the Idler pulley and bracket and bolted on the new one. Reversed the sequence of disassembly and tried it out. The only minor difficulty was slipping the belt over the idler pul ley after the drum was in place. This is where a second set of hands might be helpful to hold up the drum, while the other person puts the belt in place. Other than that, this was a simple repair and probably saved a couple hundred dollars for about 1.5 hours of my time. Thanks for the video...it was right on point, and made the job much easier.
Was this helpful?
Thank you for voting!
Making a racket.
3 of 3 people found this instruction helpful.
  • Carl from MARION, KY
  • Really Easy
  • More than 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set
Took the top off and then front off and drum out . Replaced Drum roller and shaft support bolts.
Was this helpful?
Thank you for voting!
Old. Original heat seal was deteriorated and peeling off. Streaks were getting on the clothes.
3 of 3 people found this instruction helpful.
  • Lawrence from ARITON, AL
  • A Bit Difficult
  • More than 2 hours
  • Screw drivers, Socket set
Removed the front panel, removed the tub and removed the old seal. Tub seal area was scraped, sanded and wiped with acetone to ensure a clean. Bonding surface. Applied adhesive with and acid brush to get a consistent adhesive layer without getting too much in any one place. Seal was a bit smaller than the tub circumference so it had to be stretch to fit. While the adhesive was curing , I took the time to clean the contact surfaces and vacuum the lint from inside the cabinet. Reinstalled the tub, drive belt and front panel.
Was this helpful?
Thank you for voting!
Intermittent squealing sound while dryer running
4 of 6 people found this instruction helpful.
  • John from LAKE ZURICH, IL
  • Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
Take pictures along the way.
1. Remove lower front panel using screwdriver to lift up on tabs on top of panel.
2. remove door
3. unplug moisture sensor plugs
4. remove lint trap
5. on back of dryer, remove screws holding upper lid
6. slid up lid forward just a small amount, its hooked in towards the front of the upper lid. you will need to do this so you can can remove two screws under the lid holding the front panel of the dryer on
7. remove the front panel screws mentioned in step 6.
8. Remove lower front panel screws
9. remove front panel
10. reach into dryer at the bottom and release tension from belt pulley, sliding the belt off. (make a note of how the belt is routed around the drive and idler pulleys)
11. slide out tumbling drum
12. with drum removed, use socket wrench and socket to remove old idler pulley.
13. install new idler pulley
14. reinstall tumbling drum
15. slide belt back around tumbling drum, looping belt around drive pulley and around idler pulley.
16. When belt is installed, rotate drum a few revolutions to ensure belt rides correctly.
17. Reinstall front panel
18 slide top panel back into place and secure with screws from back
19. reinstall door
20. reattach moisture sensor plugs
21. reinstall lower panel
Was this helpful?
Thank you for voting!
YouTube video dated 9/28/2015
3 of 3 people found this instruction helpful.
  • Madeline from PANA, IL
  • Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set, Wrench (Adjustable), Wrench set
How to repair E1 error/fault on Whirlpool Duet dryer model GEW9200LW0 please watch that video very helpful.
Was this helpful?
Thank you for voting!
Clothes were not drying on auto sensor.
3 of 3 people found this instruction helpful.
  • Michael from Annapolis, MD
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Followed standard instructions regarding removal of top first & then the front panels. Realized after following this process that I did not have to remove top, but only one of front panels to obtain access to moisture sensor. If I have to do this again, the replacement of sensor will be much easier.
Was this helpful?
Thank you for voting!
Dryer squealing loudly during operation
3 of 3 people found this instruction helpful.
  • Joseph from WEST PALM BCH, FL
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set
Unplug dryer from 220VAC outlet

Remove bottom cover panel, slip a flat blade screwdriver into each clamp, and bottom piece becomes removable. Pull forward and lift bottom cover piece.

Pull up top section from dryer frame. Disconnect dryer door off/on contact three wire switch by pressing plastic connector together . You may need a small flat blade screwdriver to seperate connector.

Remove two Torx (T15 head) screws in the far left and right corners of the front door panel.

Remove two screws underneath dryer lint screen, be careful to not let front door and front cover fall forward. The rotating dryer drum will now be loose.

Underneath drum, there is a cover panel over the dryer motor. Likely you will find a bunch of lint all about. This dryer had likely not been cleaned in many years.

Remove screws on dryer motor cover.
Remove panel. Likely, you’ll more lint about.
After vacuuming, use a flashlight and hand mirror to locate belt tensioner, back side of motor. If your belt is not broken, press down on the tensioner spring and remove belt from tensioner and motor. Inspect belt, replace if worn. In this instance the belt was well worn.

Slowly pull dryer drum forward, walking belt along as you bring drum forward out of the dryer casing.

At this point you have plenty of room to access the one bolt holding the tensioner, in this instance it was a 13mm socket. Be careful to remove the tensioner springs before removing the bracket. Your PartsSelect is an identical match to the original one.

Install new tensioner, tighten slightly, then put springs back on.

Reverse this entire process to get your dryer back together and back running smooth and quiet as it was when new.

This dryer was quieter than its owners remembered it being back when new 15 years ago.

Well worth saving the $ doing your own work.

Good luck on your repair endeavor!
Was this helpful?
Thank you for voting!
dryer making noise. order parts
4 of 6 people found this instruction helpful.
  • Thomas from TULELAKE, CA
  • Very Difficult
  • 30 - 60 mins
YOU NEVER SENT ME THE PARTS!!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I get my refund of the $107.26 for the parts that I never received!!
Was this helpful?
Thank you for voting!
Squealing when running
3 of 3 people found this instruction helpful.
  • MICHAEL from Baden, PA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set
You tube and supplied video directions for the make and model. Follow step by step and the repair went easy. Worried when removing the dryer drum but it went smooth.
Was this helpful?
Thank you for voting!
cold air vent in dryer was broken
3 of 3 people found this instruction helpful.
  • MIKE from WESTLAND, MI
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
remove 3 screws vent comes out put new part in works grate just like new a gain
Was this helpful?
Thank you for voting!
Bad screaming noise
3 of 3 people found this instruction helpful.
  • David from HUNTINGDON VY, PA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Replaced 4 wheels and new belt
Was this helpful?
Thank you for voting!
Coin op Whirpool Dryer Broken drive belt and frozen drum wheels
3 of 3 people found this instruction helpful.
  • Kevin from LEMOORE, CA
  • Really Easy
  • 30 - 60 mins
Removed two hex screws from upper back clips. Removed 2 Phillips screws under lint trap. Used flat head screwdriver to pry up top on front right and left side clips. (FYI: top pry's up off retaining clips in front). Remove two hex screws on right and left front panel. Un-plugged wire harness front right side. Lifted up and removed fro nt panel. This hold the drum in place. Simply removed drum, installed new belt, replaced the two drum wheels and put everything back together the same way I took it apart. 30 Minute project :)
Was this helpful?
Thank you for voting!
rollers on the tub had worn and the tub was no longer balanced.
3 of 3 people found this instruction helpful.
  • connie from NEWARK, OH
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
sounded like a pair of shoes was in the tub every time i started it no matter what size the load was. Replaced the back two rollers first and decided to start it to see how it sounded. We were glad. Only the back rollers were bad and the dryer was quietly running again. We would suggest replacing the back rollers first to everyone because the front rollers are more complicated to replace and they may not have to be at all.
Was this helpful?
Thank you for voting!
dryer did not run
3 of 3 people found this instruction helpful.
  • Gerald from STATE COLLEGE, PA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
remove top, front, drum, fan fan housing, replace motor
Was this helpful?
Thank you for voting!
All Instructions for the 110616
91 - 105 of 293