110616 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
My dryer made squeaking noise when rotating.
8 of 9 people
found this instruction helpful.
-
James from KENNESAW, GA
- Easy
- 1- 2 hours
-
Nutdriver, Screw drivers
I followed directions found on several similar YouTube videos since the instructions included in the Whirlpool parts kit were not for my model dryer. I found that the original idler pulley was not rotating and the belt had worn a groove through it. I replaced all 4 roller wheels, idler pulley and the belt. Problem solved.
Was this helpful?
Thank you for voting!
Dryer Would Not Heat
8 of 10 people
found this instruction helpful.
-
John from Raleigh, NC
- Easy
- 15 - 30 mins
-
Socket set
The dryer stopped heating. Took the front lower panel off of the dryer and obtained the troubleshooting instructions stored there. Used an ohmmeter (most volt meters also have an ohmmeter) and tested all the electrical components one by one (thermostat, thermal fuse, heater coil - following the troubleshooting instructions provided with
... Read more
the dryer) and found that I didn't have any resistance across my heater element. Removed it and sure enough there was a break in the heater coil. Ordered a new heater element from PartSelect for less than $50 and replaced it myself. Saved myself a good bit of money repairing my dryer myself. It was very straight forward and easy. If you can follow easy to read instructions you can do it.
Read less
Was this helpful?
Thank you for voting!
Original lint filter too warped to be used
7 of 7 people
found this instruction helpful.
-
David from RENO, NV
- Very Easy
- Less than 15 mins
I took out the old filter, put it into the recycle bin and dropped in the new filter. I was done.
Was this helpful?
Thank you for voting!
Dryer stopped heating
7 of 8 people
found this instruction helpful.
-
Joseph from Austin, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
(Always unplug dryer before making any repairs) I opened the dryer and checked the heating element. Making sure that the connection was good and nothing was damaged, I determined the problem was overheated wires. They melted and lots connection. I replaced them with the heating element wire connection kit. Easy to install and simple t
... Read more
o get right. I cleaned the dryer again with a vaccum cleaner, removing all the lint, and checked the vents, making sure they were clear...I turned the breaker on (it was tripped when the dryer overheated)and everything worked great.
Read less
Was this helpful?
Thank you for voting!
Lens melted because paper got behind the lens and was heated by the lamp.
6 of 6 people
found this instruction helpful.
-
Chris from Valley Stream, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
1 screw to replace.
Was this helpful?
Thank you for voting!
Dryer would start and then stop after a few minutes, eventually it completely stopped.
11 of 21 people
found this instruction helpful.
-
Keith L. from San Diego, CA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Wrench (Adjustable)
After determining that the dryer motor was the issue, I wrote down the part number and logged on to partselect.com website.
I input the number into the search box and there was the exact motor I needed.
The correct part showed up in a timely manner and the pricing was very fair.
I disassembled the dryer, ... Read more removed the old motor and reinstalled the new motor within about 30 minutes.
Key point was to read the instructions first and then reconnect the wiring to the new motor. The new motor has the switch install in a different spot on the motor so be careful to follow the instructions but, the instructions were very clear and connections were very simple.
I also did some preventive maintenance while I was in the unit by cleaning out any remaining lint from the heater unit and surrounding areas, that took about 30 minutes. Reassembling was a snap and I turned on the gas, plugged it in and........SUCCESS! Total time of repair and cleaning was about an hour.
I had a load of laundry ready to go and put the new motor right to work. It has been non-stop drying and thanks to Part Select for getting everything right the first time. It has been a positive experience and I will tell others about the website if they have similar problems. Thanks again for a success story and dry clothing.
I input the number into the search box and there was the exact motor I needed.
The correct part showed up in a timely manner and the pricing was very fair.
I disassembled the dryer, ... Read more removed the old motor and reinstalled the new motor within about 30 minutes.
Key point was to read the instructions first and then reconnect the wiring to the new motor. The new motor has the switch install in a different spot on the motor so be careful to follow the instructions but, the instructions were very clear and connections were very simple.
I also did some preventive maintenance while I was in the unit by cleaning out any remaining lint from the heater unit and surrounding areas, that took about 30 minutes. Reassembling was a snap and I turned on the gas, plugged it in and........SUCCESS! Total time of repair and cleaning was about an hour.
I had a load of laundry ready to go and put the new motor right to work. It has been non-stop drying and thanks to Part Select for getting everything right the first time. It has been a positive experience and I will tell others about the website if they have similar problems. Thanks again for a success story and dry clothing.
Read less
Was this helpful?
Thank you for voting!
Annoying loud metal to metal screeching noise.
6 of 6 people
found this instruction helpful.
-
Ricardo from ARBUCKLE, CA
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Took the front part of the dryer out, released tension on the idler pulley, took the drum out, and remove the old drum seal. Make sure you remove the old adhesive with sandpaper or wire brush. Put the new adhesive on the seal, not on the drum. Adhesive is very runny. Seal may need to be stretched to fit the drum. Set the seal on the drum
... Read more
, let sit a few minutes. Put everything back together.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer does not heat but blows only cold air
6 of 6 people
found this instruction helpful.
-
kevin from RENTON, WA
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Pulled the lower front panel located thermal switch pulled 2 wires removed 2 small bolts pulled switch out set meter to ohms scale and tested between the 2 terminals it hailed the test I reversed for installation of new switch
Was this helpful?
Thank you for voting!
Broken Motor Pulley
7 of 10 people
found this instruction helpful.
-
Mark from PELHAM, MA
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Socket set
Removed back panel of the dryer-reached my hand to the back of the motor shaft, put 7/16 wrench on it to hold the shaft while I removed the broken pulley with pliers. Very easy fix-the tech on Utube took the entire dryer apart totally unnecessary. If that is what the factory tells its tech"s to do its no wonder why the labor charge woul
... Read more
d be thru the roof.
Read less
Was this helpful?
Thank you for voting!
Dryer not heating
5 of 5 people
found this instruction helpful.
-
John from CLARKSBURG, WV
- Easy
- 1- 2 hours
-
Socket set, Wrench (Adjustable)
Replaced the heating element. Took the front lower panel off, 2 screws one on each end, removed cover on left side over blower 3 screws and removed cover lower right side over heating element 2 screws. Removed 6 wires plugged into heating element cover, turned heater element cover counter clockwise and pulled out. Removed 1 screw hold
... Read more
ing heating element inside of cover, pulled out heating element. Replaced heating element back in cover putting screw back in to hold it. Put heating element and cover into hole in back of dryer turning clockwise to secure. Then put cover holding heating element over the front of it and secured with 2 screws. Put blower cover back secured with the 3 screws and put the front cover back on securing with 2 screws. dryer is heating better than ever.
Read less
Was this helpful?
Thank you for voting!
Loose electrical wiring in dryer shorted causing connection to melt.
5 of 5 people
found this instruction helpful.
-
William from NASHVILLE, TN
- Easy
- 1- 2 hours
-
Nutdriver, Pliers, Socket set
Replaced power cord, terminal block, and all melted wiring. Checked the thermal fuse for zero resistance.
Other Parts Used:
Was this helpful?
Thank you for voting!
Drum support roller making very loud noise
5 of 5 people
found this instruction helpful.
-
William from TROY, AL
- Really Easy
- 1- 2 hours
-
Screw drivers, Socket set
had to take front off of Dryer then was able to replace drum roller
Other Parts Used:
Was this helpful?
Thank you for voting!
Dryer would not heat
5 of 5 people
found this instruction helpful.
-
GARY from PARSONS, KS
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
On this model do not try to remove the back. You must remove the bottom front panel and the lint screen unit. You can then loosen the heat coil assembly and rotate it to get to the high-limit thermostat and the thermal unit. I replaced both because I bought the kit. It actually took me longer to clean out lint than it did to replace the p
... Read more
arts. A simple remove of the parts with a 1/4 inch nut driver did the trick. Now my dryer works fine.
Read less
Was this helpful?
Thank you for voting!
Dryer wasn't heating.
5 of 5 people
found this instruction helpful.
-
Bob from OMAHA, NE
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Replaced high limit thermostat and thermal cutoff. Dryer works like a champ. Reviewed couple of YouTube videos that showed clearly how to
get to the effected parts, test them and replace them. I had an old front loading dryer once before that I repaired a couple of times but these parts were accessible by removing a panel on the ... Read more rear of the unit. The procedure was more involved with this unit. After studying the videos and getting a feel for what was involved, the process, while involved, was fairly simple and putting the unit back together was also fairly easy. Replacement parts did the trick. Very happy.
get to the effected parts, test them and replace them. I had an old front loading dryer once before that I repaired a couple of times but these parts were accessible by removing a panel on the ... Read more rear of the unit. The procedure was more involved with this unit. After studying the videos and getting a feel for what was involved, the process, while involved, was fairly simple and putting the unit back together was also fairly easy. Replacement parts did the trick. Very happy.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Old lint filter was broken
8 of 14 people
found this instruction helpful.
-
Earl from Santa Ana, CA
- Really Easy
- Less than 15 mins
Just replaced the old lint filter.
Was this helpful?
Thank you for voting!