110616 Kenmore Dryer - Instructions

All Instructions for the 110616
31 - 45 of 293

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
The sensor would not slide into grill
18 of 18 people found this instruction helpful.
  • sandra*broadnax from BRISTOW, VA
  • Easy
  • Less than 15 mins
  • Screw drivers
Initially, i watched the how to do it instruction in the fix website to determine the complexity of repairs. The instruction built up my confidence. I ordered and recieved the grill amd the two new sensors. I placed the two new sensors into the new grill sensor slots. Then removed the old grill by unscrewing three screws. Connected th e two sensors positioned the grill and screwed in the three screws put the lent stray in the grill and closed the dyer door. I have been a happy camper ever since. I saved the $75 home insurance fee plus maintenence installment. Thanks
Was this helpful?
Thank you for voting!
idler pully sqwieling
19 of 24 people found this instruction helpful.
  • Jerry Duty from Fort Walton Beach, FL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
once the back is off remove belt from tentioner and remove v clip. smooth shaft with wd-40 and scotch brite , then install new idler replace v clip
and your done !!!
Was this helpful?
Thank you for voting!
The felt strip on the filter had come undone.
21 of 31 people found this instruction helpful.
  • Rebecca from Laredo, TX
  • Really Easy
  • Less than 15 mins
Took the old filter out and inserted the new one- works great!!
Was this helpful?
Thank you for voting!
parts took more than two months to get here.
17 of 19 people found this instruction helpful.
  • rodney from Mad River, CA
  • Very Difficult
  • More than 2 hours
I'm still waiting on my idler pulley. It arrived at Fed EX depot in Tracy CA on December 14th and has still not been shipped. So it is pretty fucking hard for me to install it! Maybe if you had customer service that would answer their phones or reply to my Emails would be helpful
Was this helpful?
Thank you for voting!
Dryer starts with loud squeak initially. Eventually there was a loud clank and dryer stopped.
16 of 17 people found this instruction helpful.
  • Victor from HOUSTON, TX
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Rather than remove the front panels, door, control panel and drum, I noticed 1/4" metal screws on the back panel. There were approximately 6 holding the back panel in place. I did have to remove the top panel as well before removing the back. Once removed I had complete access to the broken idler pulley assembly. I immediately saw the b roken pulley. I installed the new one with very little effort. Reset the belt according to instructions from the video. Reassembled, plugged in, hit start and enjoyed the sweet sounds of success. All told it took me about 20 minutes from start to finish.
Was this helpful?
Thank you for voting!
Flashing E1 code for a bad thermistor
19 of 28 people found this instruction helpful.
  • John from Cedar Rapids, IA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
I replaced the thermistor earlier, but the code was still flashing. I noticed the heater terminals were charred and pretty well covered in carbon. So, I replaced the heater, the thermostat and thermal fuse and replaced the 3/8" spade terminals on the heater wires. (These are hard to find - most electrical spades terminals are .250. A lso, I crimped and soldered these for a connection with the lowest resistance possible). After all that, the code still flashed! I let the explatives fly, calmed down, and ran the control board test. (This is done by pressing "more time" "less time" "more time" "less time" in succession.) The control board was passing all the tests, but the thermistor test, and the only thing is in this circuit is the thermistor, the wires, the connector to the control board, and some circuit on the control board that involves a few resistors and the "brain" chip. So, I checked the terminals at the thermistor, the wires up to the control board and the connector at the board. The control board connector was fairly dust encrusted, so I unplugged it, cleaned the control board terminals and sucked away all the lint and dust. Finally, I carefully removed earch crimp terminal from the Molex connector (the white female connector) and cleaned and bent them to yield a better connection to the terminals on the control board. I put it all back together, and thus far it is working fine.
Was this helpful?
Thank you for voting!
Dryer tumbled but would not heat
14 of 14 people found this instruction helpful.
  • LARRY from NEWNAN, GA
  • Easy
  • 15 - 30 mins
  • Pliers, Socket set
Used socket set to remove the two hex-head screws from the bottom flange of the toe panel. Manually pulled the panel out at the bottom, pulled down, and removed the panel. Looked to right and found heater shield. Removed heather shield using socket set. Removed the two wires from the terminal block (had to use a little WD40 to loosen c onnection and wiped up afterwards). Removed the holding screw holding the heating element using the socket set. Pulled HARD on old heating element using pliers and a rag (protection from accidental cut-sharp edges). Once out, the new element slid in relatively easy. Screwed the new element back into place and re-connected the element wires, then put the heater shield back into place. Put the toe panel back into place. Tested and worked great! The only thing that made this "easy" but not "really easy" is that I had to really pull HARD on the old element to get it out...with the sharp edges and tight fit in play, you'll need to pay attention to safety when removing the old element.
Was this helpful?
Thank you for voting!
seal for lint filter came off
17 of 23 people found this instruction helpful.
  • John from Midland, TX
  • Really Easy
  • Less than 15 mins
Pulled out the old and slid in the new filter
Was this helpful?
Thank you for voting!
Dryer would not turn
15 of 18 people found this instruction helpful.
  • Kim K from Hurst, TX
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
My dryer starter squeaking in December 09 and the repairman told me that it would cost between $200-$500. I did not let him fix it as this machine is only 3 years old. When the part finally broke in April 10, I was ready to junk this and just buy a used dryer. My husband went on line and quickly figured out the part he would need to do the repairs. It cost under $20.00. Now my dryer is fixed and running and there are no squeaks. Thank you
Was this helpful?
Thank you for voting!
Dryer gasket detached from screen
14 of 17 people found this instruction helpful.
  • Richard from Duarte, CA
  • Really Easy
  • Less than 15 mins
Received in two days, open box, installed part. Pretty easy, fast service. I'm a repeat customer and will use these guys in the future.
Was this helpful?
Thank you for voting!
Dryer made a terrible screeching noise when tumbling.
13 of 14 people found this instruction helpful.
  • Richard from SAUGERTIES, NY
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
I followed the repair Vedic and took the drum out and replaced the pulls and bracket. Very straightforward job. Dryer is now as quite as the first day we bought it.
Was this helpful?
Thank you for voting!
the dryer was making squealing noises when it first started.
13 of 15 people found this instruction helpful.
  • Christine from BIRCH RUN, MI
  • Really Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers
We watched the video at whirlpool.com! Made it so simple anyone could have done it!
Was this helpful?
Thank you for voting!
Lint has been bypassing the lint filter and building up in the fan (and duct)
12 of 12 people found this instruction helpful.
  • David from PINETOWN, NC
  • Really Easy
  • Less than 15 mins
I noticed that drying time was increasing. I took the covers off the dryer to reach the fan and discovered that the squirrel cage fan buckets were packed with lint, and therefore not moving the air as intended. This was because the original lint filter caught most of the lint, but some bypassed the lint filter and then built up in the fan wheel buckets. The lint bypassed the lint filter because there was no felt gasket on the original filter as far as I can tell. I replaced the lint filter...and the replacement filter includes the felt seal (and fits tightly in the slide). The original lint filter has a provision for the felt seal, but I don't recall ever seeing it (and I did not see remnants of it in the fan or duct). As a matter of fact, I was always suspicious of how loosely the lint filter fit in the slide. The felt seal is not available as a replacement part from Maytag. That said, felt material 3/16"x1/2"x10ft is available from McMaster-Carr...and it fits nicely in the original lint filter.
Was this helpful?
Thank you for voting!
Dry was making a loud squeaking noise.
12 of 13 people found this instruction helpful.
  • Michael from OREGON CITY, OR
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers
Just watch YouTube videos. They show you how step by step. Easy to install. Clean all the dust out while dryer is apart if you can with a vacuum.
Was this helpful?
Thank you for voting!
Rear dryer drum seal came out
17 of 29 people found this instruction helpful.
  • William from Pontiac, MO
  • Easy
  • More than 2 hours
  • Screw drivers, Socket set
Used my Whirlpool Dryer User Instructions Manual and followed instructions and used the Cabinet Parts page to see the diagrams.
Was this helpful?
Thank you for voting!
All Instructions for the 110616
31 - 45 of 293