110616 Kenmore Dryer - Instructions

All Instructions for the 110616
76 - 90 of 293

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Noisy
5 of 5 people found this instruction helpful.
  • Robert from HAGERSTOWN, MD
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Disconnect power supply, remove power cord from dryer, remove dryer vent tube from dryer, remove 2 Philips screws from power connection on dryer, remove nuts from back of dryer, remove back of dryer. Locate idler pulley at bottom of unit at the rear of the motor, pull pulley back to loosen belt and remove from pulley, remove pulley retain er clip, remove pulley and rear washer from shaft and inspect shaft for wear or rust. replace washer and pulley (no specific direction to replace them, washer first then pulley). Reverse above procedure to reassemble. This is for a front load dryer, a top load dryer is different.
Was this helpful?
Thank you for voting!
couldn't get the wire connection anywhere after we bought the heating element.
6 of 8 people found this instruction helpful.
  • Betty from Erie, PA
  • Really Easy
  • 15 - 30 mins
  • Socket set
we received the two heating element wires in 3 days and connected the heating element with no problem works great.
Was this helpful?
Thank you for voting!
Lint filter seal worn out
5 of 5 people found this instruction helpful.
  • Dennis from PALM BCH GDNS, FL
  • Very Easy
  • Less than 15 mins
The part wasn’t for my machine. Unfortunaly I was not able to repair it. I was sent stripe of foam with an adhesive strip on the back. I needed a felt strip.
Was this helpful?
Thank you for voting!
Dryer made squeaking noise, then more of a rumbling noise.
5 of 6 people found this instruction helpful.
  • JAMES from NORTH OLMSTED, OH
  • A Bit Difficult
  • 1- 2 hours
  • Pliers, Socket set, Wrench set
Checked this site for most likely needed parts and ordered. Located full repair manual inside unit after removing lid. Followed instructions in manual to take apart and remove the drum; took pictures at each removal step and used pill organizer to keep screws in correct order and quantity. The metal cylinder in the center of the idler pul ley had ground away so the idler pulley with bracket was replaced. (There was a lot of metal dust that had to be cleaned.) One of the rollers did not turn smoothly so that was also replaced. After putting drum back in, reversed the steps to reassemble and referred to photos to make sure did in correct order and did not forget anything.
Was this helpful?
Thank you for voting!
Very loud squeaking noise
5 of 7 people found this instruction helpful.
  • Philip from CHICAGO, IL
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
I removed all the panels, removed the tub, replaced the pulley, put the tub back in and replaced the panels. Just when I screwed the Last screw in the doorbell rang with the door switch which I installed immediately.
Was this helpful?
Thank you for voting!
Idler pulley seized
4 of 4 people found this instruction helpful.
  • John from CREST HILL, IL
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
The pulley is accessible from the back of the dryer. Disconnect the gas line. Remove all the screws. Also remove the small plate that secures the line cord. Lift the back up and out. I was able to avoid disconnecting the water line. Take a picture of the pulley so that you will have a record of the belt routing. Release the spring and rem ove and replace the pulley and bracket. Vacuum out the lint. Plug in the dryer to make sure that it works properly before reassembly.
Was this helpful?
Thank you for voting!
Dryer drum turned hard because rollers were worn
4 of 4 people found this instruction helpful.
  • Paul from STONE CREEK, OH
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
Remove top, front and drum. Top is removed by sliding a putty knife under the front corners and pushing the tabs back. Front is held with screws. Disconnect two electrical connectors. Rollers are easily accessible and changed.
Was this helpful?
Thank you for voting!
Sqeeking noise fron old worn belt and rollers
4 of 4 people found this instruction helpful.
  • Randy from HUNTSVILLE, AL
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
Watched instructions, Ordered the kit and repair was fairly easy until the time to line up the cover over the fan wheel. That was difficult part. Would be best to have two people at this point to hold it and align the screw holes. Otherwise its was a fairly easy operation.
Was this helpful?
Thank you for voting!
My dryer was squeaking with an occasional thump
4 of 4 people found this instruction helpful.
  • Michael from BOILING SPGS, PA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Wrench set
Watched videos on line on how to repair. Replaced all four Drum Rollers, Belt and Idler Pulley, cleaned out inside of unit.
Was this helpful?
Thank you for voting!
Dryer was squealing
4 of 4 people found this instruction helpful.
  • Kevin from VALDOSTA, GA
  • Very Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Disconnected Power cord, removed vent pipe, removed back panel, had to slide top cover off to remove additional screw holding back on. Went down to where the Idler Pulley was, removed old piece by depressing on the spring loaded actuator and slid it off the belt and all. Replaced same as removal.
Was this helpful?
Thank you for voting!
Broken Drum Belt
4 of 4 people found this instruction helpful.
  • Garry from Garland, TX
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Socket set
Just like the video, just followed the video
Thanks,
Was this helpful?
Thank you for voting!
dryer was not heating up
9 of 20 people found this instruction helpful.
  • Michael from Rescue, CA
  • Really Easy
  • 15 - 30 mins
  • Socket set
take off front bottom panel. use ohm tester on the heater coil element, (It had broken in back) remove screw holding it in place and the two red wires leading to the element. Pull out and replace. reinstall in reverse. Done
Was this helpful?
Thank you for voting!
My idler pully was squealing
4 of 5 people found this instruction helpful.
  • Anthony from SAINT CLOUD, FL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I removed the bottom access panel, with 2 hands i reached in behind the blower, i released the belt, i used a screwdriver to pop the retainer from the pully spindle, i removed and replaced the pully, i snapped the retainer back on and replaced the belt. I made sure the belt was on track and all was good. I put the bottom panel back on, it took all of 5 minutes. The hardest part was the retainer clip faces the rear of the dryer so you have to feel it. Also , the space is tight, use a smaller flathead screwdriver to get behind the clip, it will pop right off.
Was this helpful?
Thank you for voting!
Roller Berings were worn out - replaced both
4 of 5 people found this instruction helpful.
  • Gregory from COCOA, FL
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers, Socket set
Watched Video - very helpful in repair Maytag Dryer working like new now Thanks for your guidance in my repair
Was this helpful?
Thank you for voting!
The blower wheel had fractured due to ingesting some metal objects (previous owner)
5 of 8 people found this instruction helpful.
  • virgil from BRECKENRIDGE, MI
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Followed instructions for standard blower wheel replacement and repair kit installation, which were straight forward. The only real issue I ran into was removing the blower wheel, The instructions say to turn it clockwise and remove it, however this wheel had been on there for a long time and it also has a taper shoulder so it was not coming off without a fight which is why the dremel tool is listed. I had to cut the old bower wheel out in pieces so I could remove the electric motor, which was easy. Once out and on the bench and only the metal hub left on the shaft a 7/16" wrench and large vise-grips got it to break loose. The good side of this is it allowed me to blow out any lint that had built up on the motor, like new again.
Was this helpful?
Thank you for voting!
All Instructions for the 110616
76 - 90 of 293