110616 Kenmore Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Repair video made it easy
2 of 2 people
found this instruction helpful.
-
Jack from DINUBA, CA
- Really Easy
- 1- 2 hours
-
Nutdriver, Screw drivers
Just follow the repair video, it was easy!
Was this helpful?
Thank you for voting!
Dryer was making a loud squeaking noise
2 of 2 people
found this instruction helpful.
-
James from Toccoa, GA
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Socket set
I followed the video instructions. I took my time as this was a first for me. The disassembly was fairly straightforward. The belt idler pulley was definitely the problem as it wouldn’t turn at all. I decided to replace the support rollers also even though they seemed to be ok. Everything I had read said my model only needed 4 rollers bu
... Read more
t actually needed 6. I had to place a second order for those. Putting it all back together was fairly easy. Overall I had a good experience. Only a few tools were needed for this repair. Thank you,
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Rollers making a noise.
2 of 2 people
found this instruction helpful.
-
Carl from MARION, KY
- Really Easy
- More than 2 hours
-
Nutdriver, Pliers, Socket set
Removed the top, removed lower front cover, removed the front, removed the belt, removed the drum and the back. Removed and replaced roller support shaft and drum roller’s. Completed all Front and rear support for drum. Replaced drum , replaced drum roller belt and replaced back, completed replacement of the top, front.
Was this helpful?
Thank you for voting!
Very loud squeaking!
2 of 2 people
found this instruction helpful.
-
Travis from GARRETT, IN
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Couple screws behind the electrical panel at the top and the top pushed back and was able to remove front panel, and then it was pretty easy. Take the two screws on top front, lint trap screws . The lint trap vent needs to come off. Then the belt, drum comes out to access the idler pulley. I did replace two drum wheels, I saw there was 5.
... Read more
I would recommend replacing all of them, they didn’t move well…..
Read less
Was this helpful?
Thank you for voting!
HEATING ELEMENT open circuit
2 of 2 people
found this instruction helpful.
-
Fred from ROCKINGHAM, VA
- A Bit Difficult
- 30 - 60 mins
-
Socket set
replacing the heating element was difficult due to the small area to work with and the defective element was difficult to slide out from housing.
Other Parts Used:
Was this helpful?
Thank you for voting!
Shutting off and had to wait before could turn back on
2 of 2 people
found this instruction helpful.
-
Allen from KENNETT, MO
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Followed online video very easy and dryer works like new one....
Was this helpful?
Thank you for voting!
Part broken in half
3 of 5 people
found this instruction helpful.
-
Sean from ROCK HILL, SC
- Really Easy
- 30 - 60 mins
-
Screw drivers
Remove screws, dryer sensor on screen. Put sensor back in place. Secure with screws. The way you take it off go in reverse.
Other Parts Used:
Was this helpful?
Thank you for voting!
lint screen was not catching lint and sending out the dryer vent
2 of 2 people
found this instruction helpful.
-
Scott from WOODBURY, MN
- Very Easy
- Less than 15 mins
replaced dryer lint screen with new.
Was this helpful?
Thank you for voting!
No leveling feet on dryer.
2 of 2 people
found this instruction helpful.
-
Bobbie from BEND, OR
- Very Easy
- Less than 15 mins
-
Wrench (Adjustable)
This could not have been easier. The hardest part was tipping the dryer over on its' side.
Instructions:
1. Tip dryer over onto a non-scratch surface. I used a tarp on the floor.
Insert leveling foot into the foot opening on the bottom of the dryer &
screw in with fingers until it is difficult to turn.
2. Use t ... Read more he adjustable wrench on the hexed foot (not the threads) to adjust to the desired level.
3. Tip dryer upright taking care not to exert pressure on the feet closest to floor. I used a folded-up tarp under the bottom edge of the dryer while lifting it to the upright position.
4. Use a level, back to front & side to side, to determine if feet need further adjustment.
5. Adjustments can be made with the dryer in the upright position, using the adjustable wrench on the hexed foot.
Instructions:
1. Tip dryer over onto a non-scratch surface. I used a tarp on the floor.
Insert leveling foot into the foot opening on the bottom of the dryer &
screw in with fingers until it is difficult to turn.
2. Use t ... Read more he adjustable wrench on the hexed foot (not the threads) to adjust to the desired level.
3. Tip dryer upright taking care not to exert pressure on the feet closest to floor. I used a folded-up tarp under the bottom edge of the dryer while lifting it to the upright position.
4. Use a level, back to front & side to side, to determine if feet need further adjustment.
5. Adjustments can be made with the dryer in the upright position, using the adjustable wrench on the hexed foot.
Read less
Was this helpful?
Thank you for voting!
Heating element went out.
2 of 2 people
found this instruction helpful.
-
Charles from SALLISAW, OK
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver
Followed the instructions all went good except for the sliding the shield back in it didn't want to go back in but it does fit. Dryer works like new again.
Was this helpful?
Thank you for voting!
Dryer kept throwing the E1 error indicating the thermistor needed replacement
2 of 3 people
found this instruction helpful.
-
Rory from LEESBURG, VA
- Easy
- 15 - 30 mins
-
Socket set
Unplugged the Dryer first. Removed the two screws from the bottom panel using a 1/4 socket and removed the panel by pulling down and out. Reached behind the blower and removed the connectors from the old thermistor and then the thermistor itself by removing the two 1/4 inch hex head screws. Replaced with new part and after screwing back i
... Read more
n, reconnected the wires and replaced the panel. From start to finish, it took me about 20 minutes.
Read less
Was this helpful?
Thank you for voting!
Screen ripped
2 of 3 people
found this instruction helpful.
-
Cindy from BENZONIA, MI
- Very Easy
- Less than 15 mins
Dropped new filter in.
Was this helpful?
Thank you for voting!
The lint filter needed replacement due to what is probably normal wear and tear.
2 of 3 people
found this instruction helpful.
-
Donna from CARY, NC
- Very Easy
- Less than 15 mins
I searched for a replacement by entering the model number and serial number of my Kenmore elite dryer. Ordering was extremely simple and it took less than a week to arrive. It fits perfectly.
Was this helpful?
Thank you for voting!
dryer was making a grinding noise
2 of 3 people
found this instruction helpful.
-
Scott from MUNCIE, IN
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
I researched causes of the noise, zeroed it down to the idler pulley. I then got the dryer schematic and took the dryer apart after disconnecting the power and the vent. i did not have to remove the drum, the idler pulley was easily accessible once the top and back panels were removed. I simply removed the drive belt from tension off the
... Read more
pulley, removed the old pulley and installed the new one. Once finished the dryer was running whisper quiet.
Read less
Was this helpful?
Thank you for voting!
Not heating up
2 of 3 people
found this instruction helpful.
-
braulio from FORT WAYNE, IN
- Very Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
I just took the old element replaced with the new one i order from this site, I save some money was really easy so proud of my self...
Was this helpful?
Thank you for voting!