1106118721 Kenmore Dryer - Instructions

All Instructions for the 1106118721
61 - 75 of 197

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Stepdaughter had over the years broke the 2 cables that supported the drop down door. So she let it hang by the hinges, which eventually broke them also.
1 person found this instruction helpful.
  • Thomas from LINCOLN, NE
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
Removed what was left of the old hinges, installed the new ones. Also added a length of jack chain (same size chain that’s on a toilet flapper) to one side to support the door while open. Tried to chain up both sides but it wouldn’t let the door completely close and depress the switch. Cables are no longer supplied by any parts dealers.
Was this helpful?
Thank you for voting!
Dryer would not start, timer had no power to it.
1 person found this instruction helpful.
  • Billy from NEW BERN, NC
  • Easy
  • 30 - 60 mins
  • Screw drivers
Raise the top off of the dryer with a flat blade screwdriver in each front corner of the dryer. Disconnect power to the dryer. Remove old switch and install new switch. Test door and proper operation of dryer.
Was this helpful?
Thank you for voting!
Light stayed on, inside dryer. Dryer no workie
1 person found this instruction helpful.
  • Steven from New Richmond, WI
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
I diagnosed the problem, as a broken arm on the actuator for the door shut switch. I jumped the switch, and dryer worked. I went to this site, found the part I needed, ordered it/received it quickly, and proceeded to do the repair. The video that THIS particular part goes for, isn't' like MY dryer. My dryer hinges in the rear. You just remove the 2 screws on either side of the control panel, (right and left), pull forward on the panel, to ease its attachment, let it lie. Then with a small plastic pry tool, pop the 2 attaching points in the front of the dryer. Front end lifts up, like a hood on a car. My roommate held hood up, while I R&R'd the switch actuator. Went back together, in reverse of my taking apart. Worked great. Thanks a bunch.
Was this helpful?
Thank you for voting!
Would not drain
1 person found this instruction helpful.
  • Robert from SANDWICH, IL
  • Really Easy
  • 15 - 30 mins
  • Wrench set
Replaced lid switch, but problem still continued.
Was this helpful?
Thank you for voting!
Dryer door wouldn't catch and stay shut
1 person found this instruction helpful.
  • Melody from TEXARKANA, TX
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
I take the screws out of the door, I removed the catch from behind inside the dryer door, I slid the new catch in the door and snapped it in place. After getting a new catch in the door I put the door back together and put the screws in. Easy repair
Was this helpful?
Thank you for voting!
door would stay closed
1 person found this instruction helpful.
  • william from KILLEEN, TX
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
just replaced parys
Was this helpful?
Thank you for voting!
Seal snapped, which lead to longer dry cycles.
2 of 4 people found this instruction helpful.
  • Christian from Sunapee, NH
  • Really Easy
  • Less than 15 mins
Just slipped it on, it was very simple. My dry cylces were reduced. Worth the $15 I spent to get the part!!!!
Was this helpful?
Thank you for voting!
door latch broke
1 person found this instruction helpful.
  • Debra from Oakland, NJ
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Pop out the old latch and replaced with a new one
Was this helpful?
Thank you for voting!
catch was missing to close dryer door
2 of 4 people found this instruction helpful.
  • DONNA from SAN LORENZO, CA
  • Really Easy
  • Less than 15 mins
The only thing I had to do was hammer the catch inside the square fitting and presto it was done. It took me less than 3 mins. I thought I might of needed instructions, but it was really simple. Even a guy can do it. (smile)
Was this helpful?
Thank you for voting!
Door would not stay closed - so dryer kept shutting off
1 person found this instruction helpful.
  • Barbara from NORTH EASTON, MA
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Followed Youtube video - quick & easy
Was this helpful?
Thank you for voting!
Broken dryer door catch
1 person found this instruction helpful.
  • Kenneth from UPPR MARLBORO, MD
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Followed the video instructions which were comprehensive, easily understood, and prefaced with a listing of necessary tools. Completely satisfied with parts and supplementary information.
Was this helpful?
Thank you for voting!
Machine would not start and light stayed on with door closed.
1 person found this instruction helpful.
  • Mark from TERREBONNE, OR
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Turned off circuit breaker to machine. Removed lint trap to allow removal of two Philips screws from vent passage that hold lid on. Opened door and removed two Philips screws that hold switch to front of machine. Using flat blade #2 screw driver pushed on plastic locking tabs under front of machine top about 2" in from either side to allo w top to be lifted up from machine. While holding up at 45 degree angle reached in and grabbed switch to pull it out for easy access. Set top down gently once switch was out. While holding switch removed broken switch actuator and installed new actuator on to switch. Lifted top back to 45 degree angle and with left hand held switch assembly in place and started two screws previously removed back into actuator holes. Tightened screws snugly. Lowered top back into plastic locking tabs and gently pushed down to secure top. Installed two screws back to air passage tube for lint trap through two holes in top that were removed at beginning of repair. Install lint trap, turn on circuit breaker and verified operation. Put wet clothes in tub, turned machine on, put away two screw drivers and kissed wife apologizing for taking so long to getting around to repairing machine.
Was this helpful?
Thank you for voting!
broken door catch
1 person found this instruction helpful.
  • Frank from ENDICOTT, NY
  • Very Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Took 3 screws out used the putty knife to pry the door a part then used the pliers to remove the old door catch and then sapped the new one and put the door back together and I was was done in less than 10 min.
Was this helpful?
Thank you for voting!
latch was broke
1 person found this instruction helpful.
  • Rick from SAN DIEGO, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
just followed the video directions, worked perfectly thanks
Was this helpful?
Thank you for voting!
dryer would not run because catch did not hold tight enough to press door switch.
1 person found this instruction helpful.
  • j from TAZEWELL, TN
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
removed screws that held the door face to gain access to catch replaced catch reassembled door tried dryer works great!
Was this helpful?
Thank you for voting!
All Instructions for the 1106118721
61 - 75 of 197